1.1 This fire-test-response standard provides for measuring the response of materials exposed to controlled levels of radiant heating with or without an external ignitor. 1.2 This test method is used to determine the ignitability, heat release rates, mass loss rates, effective heat of combustion,...
1.1 This test method covers the determination of pile thickness of finished multilevel pile yarn floor covering using a thickness measuring instrument having a stationary surface (platen), a circular pressure foot under specified force, and capable of being moved vertically above the platen....
5.1 This test method is intended for the determination of the radiant heat resistance value of a material, a combination of materials, or a comparison of different materials used in flame-resistant clothing for workers exposed to radiant thermal hazards. 5.2 This test method evaluates a material's...
1.1 This fire-test-response standard covers a small-scale laboratory procedure for determining comparative burning characteristics of solid-plastic material, using a 20-mm (50W) premixed flame applied to the base of specimens held in a vertical position. Note 1: This test method and the 20...
1.1 This practice details the procedure for determining the low-contrast visual acuity of a radiographic interpreter by evaluating the ability of the individual to detect linear images of varying radiographic noise, contrast, and sharpness. No statement is made regarding the applicability of these...
5.1 This test method provides a means for evaluation of the flammable performance of surface finish materials. 5.2 A specimen of the surface finish of concern is mounted on the support material contemplated for use and subjected to a controlled significant radiant-flux exposure. 5.3 All specimens...
1.1 This test method covers procedures for evaluating the relative mar resistance of high gloss coatings. Two test methods are included. Test Method A uses a device that rotates the test specimen on a vertical axis, against the sliding rotation of two abrading wheels. Test Method B uses a...
5.1 This test method provides a means for evaluation of the flammable performance of surface finish materials. 5.2 A specimen of the surface finish of concern is mounted on the support material contemplated for use and subjected to a controlled significant radiant-flux exposure. 5.3 All specimens...
1.1 This specification covers dry-cast concrete masonry lintels (beams) that are solid in cross-section, are reinforced for flexure, and are machine-made from hydraulic cement, water, and suitable mineral aggregates with or without the inclusion of other materials. These lintels are suitable for...
This specification applies to eye protective devices, designed for use by players of the sport of paintball that minimize or significantly reduce injury to the eye and adnexa due to impact and penetration of paintballs. Field of view, refractive tolerances, astigmatism, power imbalance, prism...
This specification covers the manufacture and purchase requirements of products used for the assembly and construction of circular vertical precast reinforced concrete manholes and structures used in sewer and water works. Reinforced concrete shall consist of cementitious materials, mineral...
1.1 This practice covers the procedure for the post installation verification and acceptance of buried pipe deformation using a visible rotating laser light diode(s), a pipeline and conduit inspection analog or digital CCTV camera system and image processing software. The combination CCTV pipe...
1.1 This practice is intended to provide accepted installation procedures for thin brick units in adhered veneer systems in residential and commercial construction. This information is meant to complement the specific installation instructions provided by manufacturers of clay and shale thin brick...
1.1 This guide describes procedures for electronically measuring the following performance-related characteristics of some sections of ultrasonic instruments: 1.1.1 Power Supply Section: ??????line regulation, ???????battery discharge time, and ???????battery charge time. 1.1.2 Pulser...
4.1 The procedures outlined in these test methods serve to evaluate the performance of the wall segments for deflection, permanent set, and maximum load-carrying capacity under transverse loading. Performance criteria based on data collected using these procedures fall outside the scope of these...
5.1 Corrosion inhibitors continue to play a key role in controlling internal corrosion associated with oil and gas production and transportation. This results primarily from the industry's extensive use of carbon and low alloy steels, which, for many applications, are economic materials of...
1.1 This test method covers the ability of steam-turbine oils to prevent the rusting of horizontal and vertical ferrous surfaces when water becomes mixed with the oil. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only....
This specification covers cylindrical corrosion-resistant tanks made of commercial-grade glass-fiber-reinforc
1.1 This specification covers zinc-coated fence fabric intended for enclosure of poultry, or to prevent entry into special areas. It is available in three styles as: 1.1.1 Poultry Netting, consisting of a mesh of woven wire with openings hexagonal in shape, 1.1.2 Poultry-and-Garden Fence Fabric,...
Narrow Your Results