loading
NOISE-VIBRATION PROBLEM - NOISE-VIBRATION PROBLEM-SOLUTION WORKBOOK
AIHA
A description is not available for this item.
ASTM C1259-21(2026) - Standard Test Method for Dynamic Young's Modulus, Shear Modulus, and Poisson's Ratio for Advanced Ceramics by Impulse Excitation of Vibration
June 1, 2026 - ASTM International

1.1 This test method covers determination of the dynamic elastic properties of advanced ceramics at ambient temperatures. Specimens of these materials possess specific mechanical resonant frequencies that are determined by the elastic modulus, mass, and geometry of the test specimen. The dynamic...

ASTM D6110-26 - Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics
July 1, 2026 - ASTM International

5.1 Before proceeding with this test method, refer to the material specification for the material being tested. Any test specimen preparation, conditioning, dimensions and testing parameters required by the materials specification shall take precedence over those required by this test method. Table...

ASTM D7387-26 - Standard Test Method for Vibration Testing of Intermediate Bulk Containers (IBCs) Used for Shipping Liquid Hazardous Materials (Dangerous Goods)
April 1, 2026 - ASTM International

4.1 Shipping containers are exposed to complex dynamic stresses when subjected to vibration present in transportation vehicles. Approximating the actual damage, or lack of damage, experienced in shipping may require subjecting the container(s) and contents to vibration inputs. 4.2...

ASTM B777-15(2026) - Standard Specification for Tungsten Base, High-Density Metal
July 1, 2026 - ASTM International

This specification establishes the requirements for four classes of machinable, high-density tungsten base metal produced by consolidating metal powder mixtures, the composition of which is mainly tungsten. This material specification may be used for bare parts or for parts that may be coated with...

ASTM C1198-20(2026) - Standard Test Method for Dynamic Young's Modulus, Shear Modulus, and Poisson's Ratio for Advanced Ceramics by Sonic Resonance
June 1, 2026 - ASTM International

1.1 This test method covers the determination of the dynamic elastic properties of advanced ceramics. Specimens of these materials possess specific mechanical resonant frequencies that are determined by the elastic modulus, mass, and geometry of the test specimen. Therefore, the dynamic elastic...

ASTM E2985/E2985M-26 - Standard Practice for Determination of Metal Purity Based on Elastic Constant Measurements Derived from Resonant Ultrasound Spectroscopy
June 15, 2026 - ASTM International

1.1 This practice is intended for use with swept sine resonant ultrasound spectrometers capable of exciting, measuring, recording, and analyzing multiple whole body mechanical vibration resonant frequencies within parts exhibiting acoustical ringing in the acoustic or ultrasonic, or both,...

ASTM C1201/C1201M-26 - Standard Test Method for Structural Performance of Exterior Dimension Stone Cladding Systems by Uniform Static Air Pressure Difference
May 1, 2026 - ASTM International

5.1 This test method gives a standard procedure for determining structural performance under uniform static air pressure difference. This typically is intended to represent the effects of wind loads on exterior building surface elements. The actual loading on building surfaces is quite complex,...

ASTM F2317/F2317M-26 - Standard Specification for Design of Weight-Shift-Control Aircraft
May 1, 2026 - ASTM International

This specification covers the minimum requirement for designing, testing, and labeling of weight-shift-control aircraft. This specification covers only weight-shift-control aircraft in which flight control systems do not use hinged surfaces controlled by the pilot. Flight requirements are specified...

ASTM C1959/C1959M-26 - Standard Test Method for Non-Contact Measurement of Resonant Frequencies of Concrete Cylinders
March 1, 2026 - ASTM International

5.1 While this test method serves a similar purpose as Test Method C215, attachment of a vibration sensor to the cylinder is not required, and requirements for preparing and supporting the specimen for testing are different. Smartphones or tablet computers can perform the required data...

ASTM D256-26 - Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
April 1, 2026 - ASTM International

5.1 Before proceeding with these test methods, refer to the specification of the material being tested. Any test specimen preparation, conditioning, dimensions, and testing parameters covered in the materials specification shall take precedence over those mentioned in these test methods. If there...

ASTM E328-26 - Standard Test Methods for Stress Relaxation for Materials and Structures
April 1, 2026 - ASTM International

5.1 Stress-relaxation test data are necessary when designing most mechanically fastened joints to ensure the permanent tightness of bolted or riveted assemblies, press or shrink-fit components, rolled-in tubes, etc. Other applications include predicting the decrease in the tightness of gaskets, in...

ASTM C232/C232M-26 - Standard Test Method for Bleeding of Concrete
January 1, 2026 - ASTM International

4.1 This test method provides procedures to be used for determining the effect of variables of composition, treatment, environment, or other factors in the bleeding of concrete. This test method is also permitted to be used to determine the conformance of a product or treatment with a requirement...

ASTM C192/C192M-26 - Standard Practice for Making and Curing Concrete Test Specimens in the Laboratory
February 1, 2026 - ASTM International

1.1 This practice covers procedures for making and curing test specimens of concrete in the laboratory under accurate control of materials and test conditions using concrete that can be consolidated by rodding or vibration as described herein. 1.2 The values stated in either SI units or...

ASTM A962/A962M-26 - Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range
February 1, 2026 - ASTM International

1.1 This specification covers a group of common requirements that shall apply to carbon, alloy, stainless steel, and nickel alloy bolting under any of the following ASTM Specifications (or under any other ASTM Specifications that invoke this specification or portions thereof): Title of...

ASTM D1932-19(2025) - Standard Test Method for Thermal Endurance of Flexible Electrical Insulating Varnishes
December 1, 2025 - ASTM International

5.1 A major factor affecting the long term performance of insulating materials is thermal degradation. It is possible that factors, such as moisture and vibration, will cause failures after the material has been weakened by thermal degradation. 5.2 An electrical insulating varnish is...

ASTM E664/E664M-25 - Standard Practice for the Measurement of the Apparent Attenuation of Longitudinal Ultrasonic Waves by Immersion Method
December 1, 2025 - ASTM International

5.1 The measurement of apparent attenuation in materials is useful in applications such as the comparison of heat treatments of different lots of material or the assessment of the degradation of materials due to environment. 5.2 Several different modes of wave vibration can be propagated in...

ASTM D7894/D7894M-19(2025) - Standard Test Method for Thermal Endurance of Coating Powders Used for Integral Bus Bar Insulation Systems
December 1, 2025 - ASTM International

5.1 A major factor affecting the life of insulating materials is thermal degradation. It is possible that other factors, such as moisture and vibration, will cause failures after the material has been weakened by thermal degradation. 5.2 Electrical insulation is effective in electrical...

ASTM D7895/D7895M-19(2025) - Standard Test Method for Thermal Endurance of Coating Powders Used for Powder Coating Insulation Systems
December 1, 2025 - ASTM International

5.1 A major factor affecting the life of insulating materials is thermal degradation. It is possible that other factors, such as moisture and vibration, will cause failures after the material has been weakened by thermal degradation. 5.2 Electrical insulation is effective in electrical...

Advertisement