loading
PCMCIA SYSTEM - PCMCIA SYSTEM ARCHITECTURE
PCMCIA
A description is not available for this item.
IEEE INFORMATION - INFORMATION GRAPHICS: A COMPRHENSIVE ILLUSTRATED REFERENCE
IEEE
A description is not available for this item.
ASHRAE SYSTEMS & EQUIP SI - 2020 ASHRAE Handbook HVAC Systems and Equipment SI Edition
January 1, 2020 - ASHRAE
A description is not available for this item.
ASHRAE SYSTEMS & EQUIP IP - 2020 ASHRAE Handbook HVAC Systems and Equipment I-P Edition
January 1, 2020 - ASHRAE
A description is not available for this item.
IEEE INFORMATION THEORY: - INFORMATION THEROY: 50 YEARS OF DISCOVERY
IEEE
A description is not available for this item.
ASTM C143/C143M-26b - Standard Test Method for Slump of Concrete
June 1, 2026 - ASTM International

1.1 This test method covers determination of slump of concrete, both in the laboratory and in the field. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore,...

ASTM D1092-26 - Standard Test Method for Measuring Apparent Viscosity of Lubricating Greases
June 1, 2026 - ASTM International

5.1 Apparent viscosity versus shear rate information can be useful in predicting pressure drops in grease distribution systems under steady-state flow conditions at constant temperature.

ASTM C1935-26 - Standard Practice for Installation Methods for Adhered Veneer Systems Using Thin Brick Units Made from Clay or Shale
June 1, 2026 - ASTM International

4.1 This practice provides information that, if implemented, will facilitate good installation practices for thin brick in an adhered veneer system. However, this practice cannot address every situation encountered. Applicable building codes and industry design standards may provide...

ASTM F3825-26 - Standard Specification for Operating Limitations, Markings, Placards, and Warnings for Light Sport Aircraft
May 1, 2026 - ASTM International

1.1 This specification covers the requirement for operating limitations, markings, placards, and warnings for light sport aircraft. This includes those items necessary for safe operation and occupant warnings. It also defines the minimum requirements for legibility and consistency of...

ASTM F3832-26 - Standard Specification for Rotors and Rotor Systems for Light Sport Helicopters
May 1, 2026 - ASTM International

1.1 This specification covers the performance, safety, and marking requirements for main lift rotors and anti-torque systems, including rotor speed limits, drive system design, warning systems, operational limitations, and documentation requirements. 1.2 Units-The values...

ASTM D3289-17(2026) - Standard Test Method for Density of Semi-Solid and Solid Asphalt Materials (Nickel Crucible Method)
June 1, 2026 - ASTM International

1.1 This test method covers the determination of the density of semi-solid and solid asphalt materials by weighing in air and in water. Note 1: An alternate method for determining the density of semi-solid and solid asphalt materials is Test Method D70/D70M. For materials which are too fluid for...

ASTM D6897-26 - Standard Test Method for Vapor Pressure of Liquefied Petroleum Gases (LPG) (Expansion Method)
June 1, 2026 - ASTM International

5.1 Information on the vapor pressures of liquefied petroleum gas is pertinent to selection of properly designed storage vessels, shipping containers, and customer utilization equipment to ensure safe handling of these products. 5.2 Determination of the vapor pressure of liquefied petroleum...

ASTM F2075-26 - Standard Specification for Engineered Wood Fiber for Use as a Playground Safety Surface Under and Around Playground Equipment
June 1, 2026 - ASTM International

1.1 This specification establishes minimum characteristics for those factors that determine particle size, consistency, purity, and ability to drain. 1.2 Engineered wood fiber that meets the requirements of this specification must comply with Specification F1292, if the surface is in the use zone...

ASTM F1821-26 - Standard Consumer Safety Specification for Toddler Beds
February 1, 2026 - ASTM International

1.1 This consumer safety specification covers requirements for the design and performance of toddler beds. It also contains requirements for labeling and instructional material. 1.2 This consumer safety specification is intended to minimize incidents to children resulting from normal use and...

ASTM G96-90(2026) - Standard Guide for Online Monitoring of Corrosion in Plant Equipment (Electrical and Electrochemical Methods)
February 1, 2026 - ASTM International

5.1 General corrosion is characterized by areas of greater or lesser attack, throughout the plant, at a particular location, or even on a particular probe. Therefore, the estimation of corrosion rate as with mass loss coupons involves an averaging across the surface of the probe. Allowance must be...

ASTM F1235-25 - Standard Consumer Safety Specification for Portable Hook-On Chairs
November 15, 2025 - ASTM International

This consumer safety specification covers the performance requirements and test methods designed to ensure the satisfactory performance, and hence, minimize injuries to children resulting from normal use and reasonably foreseeable misuse or abuse of portable hook-on chairs. Chairs that conform to...

Advertisement