1.1 This test method is used to establish the concentration of free cyanide in an aqueous wastewater, effluent and in-stream free cyanide concentrations after mixing treated water with receiving water. The test conditions of this test method are used to measure free cyanide (HCN and CN-) and...
1.1 This test method covers the determination of total oil and grease (TOG) that can be extracted from water or wastewater samples by cyclohexane and measured by non-dispersive IR spectroscopy from 1370?cm-1 to 1380?cm-1. Treating the extract with Florisil to remove polar substances prior to...
1.1 This test method covers the liquid chromatography tandem mass spectrometry (LC-MS/MS) detection and quantitation of N-nitrosamines after direct injection. It has been validated for groundwater, surface water, wastewater influents, and wastewater effluents. This test method is not...
5.1 Purgeable organic compounds have been identified as contaminants in treated drinking water, wastewater, ground water, and Toxicity Characteristic Leaching Procedure (TCLP) leachate. These contaminants may be harmful to the environment and to people. Purge and trap sampling is a generally...
5.1 This test method is useful for the determination of element concentrations in many natural waters, metallurgical process solutions, mine impacted waters, wastewaters, biological materials, soil, and geochemical samples. It has the capability for the determination of up to 72 elements....
1.1 This test method covers the determination of ammonia nitrogen in surface water, ground water, drinking water, municipal and industrial wastewater, seawater, and potassium chloride soil extracts. A gas diffusion step eliminates the need for preliminary distillation. 1.2 The applicable...
1.1 This terminology covers those terms recommended by the International Union of Pure and Applied Chemistry (IUPAC), and is intended to provide guidance in the use of ion-selective electrodes for analytical measurement of species in water, wastewater, and brines. 1.2 This international...
5.1 Inorganic constituents in water and wastewater must be identified and measured to support effective water quality monitoring and control programs. Currently, one of the simplest, most practical and cost effective means of accomplishing this is through the use of chemical test kits and...
1.1 This test method covers the determination of dissolved and total recoverable strontium in water and wastewater by atomic absorption spectroscopy. 1.2 The test method is applicable in the range from 0.1?mg/L to 1?mg/L of strontium. The range may be extended by dilution of the original...
1.1 This test method covers the determination of dissolved and total recoverable barium in most waters and wastewaters. 1.2 This test method was evaluated in the range from 33.5?μg/L to 132?μg/L of barium. The range can be increased or decreased by varying the volume of sample injected or...
1.1 This practice covers the general considerations for quantitative sample digestion for total metals in water using closed vessel microwave heating technique. This practice is applicable to surface, saline, domestic, and industrial wastewater. 1.2 Because of the differences among various...
1.1 This guide identifies procedures for use in developing and optimizing new or modified Subcommittees D19.05 and D19.06 test methods intended for regulatory compliance reporting in EPA drinking water and wastewater programs. This guide may also be useful for developing test methods for...
1.1 This practice describes the minimum loads to be applied when designing monolithic or sectional precast concrete water and wastewater structures with the exception of concrete pipe, box culverts, utility structures, and material covered in Specification C478/C478M. 1.2 The values stated...
1.1 This practice covers procedures for estimating the dimensions and marking the boundaries of a soil absorption area for an on-site septic system involving residential-strength
1.1 This practice covers procedures for onsite testing precast concrete water and wastewater structures using exfiltration acceptance limits to demonstrate the integrity of the installed materials, including structural integrity, and construction processes, with the exception of items...
5.1 This test method describes a rapid method to determine the maximum quantity of oxygen that may be consumed by impurities in water. As outlined in Test Methods D1252, chemical oxygen demand is typically used to monitor and control oxygen-consuming pollutants, both organic and inorganic, in...
5.1 There is increasing concern regarding water quality. The first national-scale U.S. examination of these organic wastewater contaminants in streams, conducted by the Toxic Substances Hydrology Program of the U.S. Geological Survey (USGS), indicated that a broad range of chemicals found in...
4.1 This guide is intended for use by both generators and users of analytical results. It is intended to promote consistent demonstration and documentation of the quality of the measurement results and facilitate determination of the validity of measurements for their intended use. 4.2 This guide...
1.1 In this guide, practitioners are informed on the considerations relevant to the environmental field sampling component of data acquisition programs for per- and polyfluoroalkyl substances (PFAS). 1.2 In this guide, the collection of environmental media, including potable water (such as drinking...
Narrow Your Results