loading
ASCE MUNICIPAL WASTEWATER - DESIGN OF MUNICIPAL WASTEWATER TREATMENT PLANTS
ASCE
A description is not available for this item.
ASTM D7237-18(2026) - Standard Test Method for Free Cyanide and Aquatic Free Cyanide with Flow Injection Analysis (FIA) Utilizing Gas Diffusion Separation and Amperometric Detection
July 15, 2026 - ASTM International

1.1 This test method is used to establish the concentration of free cyanide in an aqueous wastewater, effluent and in-stream free cyanide concentrations after mixing treated water with receiving water. The test conditions of this test method are used to measure free cyanide (HCN and CN-) and...

ASTM D8193-26 - Standard Test Method for Total Oil and Grease (TOG) and Total Petroleum Hydrocarbon (TPH) in Water and Wastewater with Solvent Extraction Using Non-Dispersive Mid-IR Transmission Spectroscopy
May 15, 2026 - ASTM International

1.1 This test method covers the determination of total oil and grease (TOG) that can be extracted from water or wastewater samples by cyclohexane and measured by non-dispersive IR spectroscopy from 1370?cm-1 to 1380?cm-1. Treating the extract with Florisil to remove polar substances prior to...

ASTM D8456-26 - Standard Test Method for Determination of Nitrosamines in Water by Liquid Chromatography Tandem Mass Spectrometry (LC-MS/MS)
July 1, 2026 - ASTM International

1.1 This test method covers the liquid chromatography tandem mass spectrometry (LC-MS/MS) detection and quantitation of N-nitrosamines after direct injection. It has been validated for groundwater, surface water, wastewater influents, and wastewater effluents. This test method is not...

ASTM D5790-18(2026) - Standard Test Method for Measurement of Purgeable Organic Compounds in Water by Capillary Column Gas Chromatography/Mass Spectrometry
July 1, 2026 - ASTM International

5.1 Purgeable organic compounds have been identified as contaminants in treated drinking water, wastewater, ground water, and Toxicity Characteristic Leaching Procedure (TCLP) leachate. These contaminants may be harmful to the environment and to people. Purge and trap sampling is a generally...

ASTM D8607-26 - Standard Test Method for Determination of Selected Elements in Aqueous Solutions by Single Quadrupole Inductively Coupled Plasma-Mass Spectrometry (ICP-MS)
July 1, 2026 - ASTM International

5.1 This test method is useful for the determination of element concentrations in many natural waters, metallurgical process solutions, mine impacted waters, wastewaters, biological materials, soil, and geochemical samples. It has the capability for the determination of up to 72 elements....

ASTM D8430-26 - Standard Test Method for Determination of Ammonia Nitrogen by Semi-Automated Gas Diffusion Colorimetry
July 1, 2026 - ASTM International

1.1 This test method covers the determination of ammonia nitrogen in surface water, ground water, drinking water, municipal and industrial wastewater, seawater, and potassium chloride soil extracts. A gas diffusion step eliminates the need for preliminary distillation. 1.2 The applicable...

ASTM D4127-18a(2026) - Standard Terminology Used with Ion-Selective Electrodes
May 1, 2026 - ASTM International

1.1 This terminology covers those terms recommended by the International Union of Pure and Applied Chemistry (IUPAC), and is intended to provide guidance in the use of ion-selective electrodes for analytical measurement of species in water, wastewater, and brines. 1.2 This international...

ASTM D5463-18(2026) - Standard Guide for Use of Test Kits to Measure Inorganic Constituents in Water
May 1, 2026 - ASTM International

5.1 Inorganic constituents in water and wastewater must be identified and measured to support effective water quality monitoring and control programs. Currently, one of the simplest, most practical and cost effective means of accomplishing this is through the use of chemical test kits and...

ASTM D3920-18(2026) - Standard Test Method for Strontium in Water
May 1, 2026 - ASTM International

1.1 This test method covers the determination of dissolved and total recoverable strontium in water and wastewater by atomic absorption spectroscopy. 1.2 The test method is applicable in the range from 0.1?mg/L to 1?mg/L of strontium. The range may be extended by dilution of the original...

ASTM D4382-18(2026) - Standard Test Method for Barium in Water, Atomic Absorption Spectrophotometry, Graphite Furnace
May 1, 2026 - ASTM International

1.1 This test method covers the determination of dissolved and total recoverable barium in most waters and wastewaters. 1.2 This test method was evaluated in the range from 33.5?μg/L to 132?μg/L of barium. The range can be increased or decreased by varying the volume of sample injected or...

ASTM D4309-18(2026) - Standard Practice for Sample Digestion Using Closed Vessel Microwave Heating Technique for the Determination of Total Metals in Water
May 1, 2026 - ASTM International

1.1 This practice covers the general considerations for quantitative sample digestion for total metals in water using closed vessel microwave heating technique. This practice is applicable to surface, saline, domestic, and industrial wastewater. 1.2 Because of the differences among various...

ASTM D8272-19(2026) - Standard Guide for Development and Optimization of D19 Chemical Analysis Methods Intended for EPA Compliance Reporting
May 1, 2026 - ASTM International

1.1 This guide identifies procedures for use in developing and optimizing new or modified Subcommittees D19.05 and D19.06 test methods intended for regulatory compliance reporting in EPA drinking water and wastewater programs. This guide may also be useful for developing test methods for...

ASTM C890/C890M-26 - Standard Practice for Minimum Structural Design Loading for Monolithic or Sectional Precast Concrete Water and Wastewater Structures
February 1, 2026 - ASTM International

1.1 This practice describes the minimum loads to be applied when designing monolithic or sectional precast concrete water and wastewater structures with the exception of concrete pipe, box culverts, utility structures, and material covered in Specification C478/C478M. 1.2 The values stated...

ASTM D5925-26 - Standard Practice for Preliminary Sizing and Delineation of Soil Absorption Field Areas for On-Site Septic Systems
February 15, 2026 - ASTM International

1.1 This practice covers procedures for estimating the dimensions and marking the boundaries of a soil absorption area for an on-site septic system involving residential-strength wastewater. It can also be used to estimate the dimensions of commercial on-site septic systems where...

ASTM C1957/C1957M-25 - Standard Practice for Onsite Exfiltration Acceptance Testing of Precast Concrete Water and Wastewater Structures
December 1, 2025 - ASTM International

1.1 This practice covers procedures for onsite testing precast concrete water and wastewater structures using exfiltration acceptance limits to demonstrate the integrity of the installed materials, including structural integrity, and construction processes, with the exception of items...

ASTM D8084-26 - Standard Test Method for Photoelectrochemical Oxygen Demand of Freshwater Sources for Drinking Water Treatment Plants and Treated Drinking Water
January 1, 2026 - ASTM International

5.1 This test method describes a rapid method to determine the maximum quantity of oxygen that may be consumed by impurities in water. As outlined in Test Methods D1252, chemical oxygen demand is typically used to monitor and control oxygen-consuming pollutants, both organic and inorganic, in...

ASTM E2717-18(2025) - Standard Practice for Estimating the Environmental Load of Residential Wastewater
June 1, 2025 - ASTM International

5.1 There is increasing concern regarding water quality. The first national-scale U.S. examination of these organic wastewater contaminants in streams, conducted by the Toxic Substances Hydrology Program of the U.S. Geological Survey (USGS), indicated that a broad range of chemicals found in...

ASTM D6956-17(2026) - Standard Guide for Demonstrating and Assessing Whether a Chemical Analytical Measurement System Provides Analytical Results Consistent with Their Intended Use
January 1, 2026 - ASTM International

4.1 This guide is intended for use by both generators and users of analytical results. It is intended to promote consistent demonstration and documentation of the quality of the measurement results and facilitate determination of the validity of measurements for their intended use. 4.2 This guide...

ASTM E3511-26 - Standard Guide for Per- and Polyfluoroalkyl Substances (PFAS) Sampling of Environmental Media
January 1, 2026 - ASTM International

1.1 In this guide, practitioners are informed on the considerations relevant to the environmental field sampling component of data acquisition programs for per- and polyfluoroalkyl substances (PFAS). 1.2 In this guide, the collection of environmental media, including potable water (such as drinking...

Advertisement