loading
HI WATER TREATMENT PLANT - Water Treatment Plant Pumps: Guidelines For Selection, Application, And Operation
January 1, 2017 - HI/HYDRAUL
A description is not available for this item.
SWRI WATER REPELLANT - CLEAR WATER REPELLENT FOR MASONRY
January 1, 1994 - SWRI

This comprehensive manual includes information on clear water repellent materials for both vertical and horizontal surfaces. Also included are a glossary, product comparisons, specifications, monograph and performance test criteria.

WATER TREATMENT PLANT - WATER TREATMENT PLANT DESIGN
AWWA
A description is not available for this item.
NSF WATER ADDITIVE SET - DRINKING WATER ADDITIVE SET - STANDARDS 60 AND 61
NSF
A description is not available for this item.
ASTM F645-25 - Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems
March 1, 2025 - ASTM International

4.1 The requirements of this specification are intended to provide information to select, design and install thermoplastic, water-pressure piping systems. Materials covered in this specification are Poly(Vinyl Chloride) (PVC), Chlorinated Poly(Vinyl Chloride) (CPVC) and Polyethylene...

ASTM E2140-01(2023) - Standard Test Method for Water Penetration of Metal Roof Panel Systems by Static Water Pressure Head
July 1, 2023 - ASTM International

1.1 This laboratory test method covers the determination of the resistance to water penetration of exterior metal roof panel system sideseams, endlaps, and roof plane penetrations when a specified static water pressure head is applied to the outside face of the roof panel. Note...

ASTM D4188-17(2025) - Standard Practice for Performing Pressure In-Line Coagulation-Flocculation-Filtration Test in Water
December 1, 2025 - ASTM International

1.1 This practice covers the procedure used to perform pressure in-line coagulation-flocculation-filtration of water and waste water. It is applicable to water and waste water with relatively low suspended solids (<30 mg/L). The practice is applicable for any size...

ASTM D5367-26 - Standard Practice for Evaluating Coatings Applied Over Surfaces Treated With Additives Used to Prevent Flash Rusting of Steel When Vapor, Water, or Water/Abrasive Blasted
June 1, 2026 - ASTM International

1.1 This practice covers procedures to evaluate the compatibility of coatings with additives used to prevent flash rusting of steel before application of coatings. 1.2 The additives are used with vapor blast, wet abrasive blast (WAB), low or high pressure water cleaning (LPWC, HPWC),...

ASTM E2006-22(2026) - Standard Guide for Benchmark Testing of Light Water Reactor Calculations
June 1, 2026 - ASTM International

1.1 This guide covers general approaches for benchmarking neutron transport calculations for pressure vessel surveillance programs in light water reactor systems. A companion guide (Guide E2005) covers use of benchmark fields for testing neutron transport calculations and cross...

ASTM F877-26 - Standard Specification for Crosslinked Polyethylene (PEX) Hot- and Cold-Water Distribution Systems
August 1, 2026 - ASTM International

This specification covers requirements, test methods, and methods of marking for crosslinked polyethylene plastic hot- and cold-water distribution systems components made in one standard dimension ratio. Components are comprised of tubing and fittings intended for use in residential and...

ASTM F2324-13(2026) - Standard Test Method for Prerinse Spray Valves
March 1, 2026 - ASTM International

5.1 The flow rate test is used to confirm that the prerinse spray valve is operating at the manufacturer's rated flow rate at the specified water pressure. The result from this test would also assist the operator in controlling the water and sewer consumption and reduce...

ASTM F1370-92(2024) - Standard Specification for Pressure-Reducing Valves for Water Systems, Shipboard
November 15, 2024 - ASTM International

1.1 This specification covers self-contained, globe style, pressure-reducing valves for use in water systems of shipboard installations. These valves are limited to discharge pressure settings of 200 psig (1379 kPa) and below. 1.2 The values stated in inch-pound units are to be...

ASTM D5482-26 - Standard Test Method for Vapor Pressure of Petroleum Products and Liquid Fuels (Mini Method—Atmospheric)
May 1, 2026 - ASTM International

5.1 Vapor pressure is an important physical property of volatile liquids. 5.2 Vapor pressure is critically important for both automotive and aviation gasolines, affecting starting, warm-up, and tendency to vapor lock with high operating temperatures or high altitudes. Maximum vapor...

ASTM D323-26 - Standard Test Method for Vapor Pressure of Petroleum Products (Reid Method)
May 1, 2026 - ASTM International

5.1 Vapor pressure is an important physical property of volatile liquids. This test method is used to determine the vapor pressure at 37.8?°C (100?°F) of petroleum products and crude oils with initial boiling point above 0?°C (32?°F). 5.2 Vapor pressure is critically important...

ASTM A965/A965M-26 - Standard Specification for Steel Forgings, Austenitic, for Pressure and High Temperature Parts
June 1, 2026 - ASTM International

This specification covers austenitic stainless steel forgings for pressure and high temperature parts such as boilers, pressure vessels, and associated equipment. The grades covered here are F304, F304H, F304L, F304N, F304LN, F309H, F310, F310H, F316, F316H, F316L, F316N, F316LN,...

ASTM C430-26 - Standard Test Method for Fineness of Hydraulic Cement by the 45-μm (No. 325) Sieve
June 1, 2026 - ASTM International

This test method covers hydraulic cement fineness tests performed using a sieve. The sieve frame should be made of a circular metal matching the specified dimensions, fitted with either a stainless steel woven-wire sieve cloth or an electroformed forced nickel sieve sheet. Both the nozzle and sieve...

ASTM D8236-26 - Standard Practice for Preparing an Equilibrium Liquid/Vapor Sample of Live Crude Oil, Condensates, or Liquid Petroleum Products Using a Manual Piston Cylinder for Subsequent Liquid Analysis or Gas Analysis
May 1, 2026 - ASTM International

5.1 This practice allows for compositional analysis of the gases in equilibrium with crude oil, condensate, and liquid petroleum products at a 4:1 vapor/liquid ratio at ambient temperature for analysis using typical instrumentation (RGA) already available in typical refinery laboratories. These...

Advertisement