loading
ASTM C732-17(2026) - Standard Test Method for Aging Effects of Artificial Weathering on Latex Sealants
July 1, 2026 - ASTM International

1.1 This test method covers a laboratory procedure for the determination of aging effects of artificial weathering on latex sealants. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not...

ASTM D4677-87(2026) - Standard Classification for Rubber Compounding Materials—Titanium Dioxide
July 1, 2026 - ASTM International

3.1 Titanium dioxide is used in rubber compounding as a colorant to impart whiteness to any desired end product. It is used in sidewalls of automobile tires. 3.2 It is chemically inert and slightly basic with a pH of 7.0 to 8.0. The free-chalking, weathering properties of anatase...

ASTM C129-26 - Standard Specification for Dry-Cast Nonloadbearing Concrete Masonry Units
July 15, 2026 - ASTM International

1.1 This specification covers dry-cast hollow and solid nonloadbearing concrete masonry units machine-made from hydraulic cement, water, and suitable mineral aggregates with or without the inclusion of other materials. These units are intended for use in nonloadbearing partitions, but under certain...

ASTM D7897-26 - Standard Practice for Laboratory Soiling and Weathering of Roofing Materials to Simulate Effects of Natural Exposure on Solar Reflectance and Thermal Emittance
July 1, 2026 - ASTM International

5.1 The solar reflectance of a building envelope surface affects surface temperature and near-surface ambient air temperature. Surfaces with low solar reflectance absorb a high fraction of the incoming solar energy. Sunlight absorbed by a roof or by other building envelope surfaces can be conducted...

ASTM C1195-21(2026) - Standard Test Method for Absorption of Architectural Cast Stone
June 1, 2026 - ASTM International

4.1 This test method is to be used in determining the absorption value of cast stone. Absorption is one measure of porosity of cast stone and, hence, its resistance to weathering and in-service durability.

ASTM E3534-26 - Standard Test Method for Vacuum Insulating Glass Durability
July 1, 2026 - ASTM International

1.1 This test method covers procedures for testing the durability of preassembled, permanently sealed vacuum insulating glass (VIG) units. 1.2 This test method is applicable only to VIG units that are constructed with flat glass lites (glass panes). 1.3 This test method is applicable to units made...

ASTM E3006-20(2026) - Standard Practice for Ultraviolet Conditioning of Photovoltaic Modules or Mini-Modules Using a Fluorescent Ultraviolet (UV) Lamp Apparatus
June 1, 2026 - ASTM International

5.1 Photovoltaic modules and components must be resistant to prolonged exposure to solar radiation, moisture, and heat. Degradation of polymeric components, delamination at the encapsulant and other interfaces, and moisture ingress are among the degradation modes known to decrease the output of...

ASTM C216-26a - Standard Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)
June 1, 2026 - ASTM International

This specification covers brick intended for use in masonry and supplying structural or facing components, or both, to the structure. Bricks shall be classified according to their resistance to damage by freezing when saturated at a moisture content: Grade SW and Grade MW. The facing bricks shall...

ASTM D5590-26 - Standard Test Method for Determining the Resistance of Paint Films and Related Coatings to Fungal Defacement by Accelerated Four-Week Agar Plate Assay
June 1, 2026 - ASTM International

4.1 Defacement of paint and coating films by fungal growth (mold, mildew) is a common phenomenon, and defacement by algal growth as referenced in Test Method D5589 can also occur under certain conditions. It is generally known that differences in the environment, lighting, temperature, humidity,...

ASTM D7694/D7694M-18(2026) - Standard Test Methods for Self-Adhesive Modified Bituminous Sheet Material
May 1, 2026 - ASTM International

3.1 These test methods are used to evaluate the properties of self-adhesive modified bituminous membranes. The results determine compliance with the applicable specifications, or they can be used for comparative analysis. 3.2 The test methods apply to "as manufactured" material and may not apply to...

ASTM C1088-26 - Standard Specification for Thin Veneer Brick Units Made From Clay or Shale
June 1, 2026 - ASTM International

This specification covers thin veneer brick units made from clay, shale, fire clay, sand, or mixtures thereof, and fired to incipient fusion for use in adhered or fastened veneer applications. The brick units shall be available in both Grades Interior and Exterior of the following types: Type TBS...

ASTM C901-26 - Standard Guide for Design and Installation of Prefabricated Masonry Elements
June 1, 2026 - ASTM International

4.1 This guide is intended to provide information and guidance for designers, specifiers, manufacturers, contractors and users that are considering the use of prefabricated masonry elements. This guide identifies situations when prefabrication could be considered where other prefabricated systems...

ASTM E3325-21(2026) - Standard Practice for Sampling of Solar Photovoltaic Modules for Toxicity Testing
June 1, 2026 - ASTM International

6.1 The primary goal of this practice is to extract representative samples from PV modules for TCLP toxicity testing purposes in order to receive unbiased, comparable, and repeatable toxicity test results from independent TCLP testing laboratories. 6.2 Solar photovoltaic (PV) modules in the United...

ASTM D1369-19(2026) - Standard Practice for Quantities of Materials for Asphalt-Aggregate Surface Treatments
May 1, 2026 - ASTM International

4.1 This practice is intended to be used as a guide by those involved in the design of asphalt surface treatments. It covers typical application rates for the various types of surface treatments and covers aggregate sizes and recommended grades of asphaltic material for both hot and cool...

ASTM C1519-10(2026) - Standard Test Method for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures
April 1, 2026 - ASTM International

4.1 This test method describes the procedure to evaluate or compare, or both, the durability of sealants when subjected to accelerated weathering and cyclic movement in a joint. 4.2 Sealant installation procedures, design considerations and movement during cure affect the aging processes and...

ASTM D6878/D6878M-26 - Standard Specification for Thermoplastic Polyolefin-Based Sheet Roofing
May 1, 2026 - ASTM International

This specification covers flexible sheet made from thermoplastic polyolefin (TPO) as the principal polymer, intended for use in single-ply roofing membranes exposed to the weather. The sheet shall contain reinforcing fabrics or scrims. The sheet shall be formulated from ethylene and higher...

ASTM C780-26 - Standard Test Methods for Preconstruction and Construction Evaluation of Mortars for Plain and Reinforced Unit Masonry
June 1, 2026 - ASTM International

5.1 During preconstruction and construction evaluations, use of these test methods establishes specific and overall performance characteristics for the mortar system. 5.2 Preconstruction testing of mortars prebatched by weight provides information for the selection of the individual mortar system...

ASTM D6929-21(2026) - Standard Practice for Evaluating the Effect of Freezing on Emulsified Asphalts
May 1, 2026 - ASTM International

3.1 Certain agencies who desire to use, store, or transport emulsified asphalt under less than ideal weather conditions may require that the product remain homogeneous (unbroken) after being subjected to a temperature of -18?°C. Note 1: The quality of the results produced by this standard...

ASTM E3524/E3524M-26 - Standard Test Methods for Evaluating Ground Response Robot Capabilities: Dexterity: Rotate
April 15, 2026 - ASTM International

5.1 These test methods are part of an overall suite of related test methods that provide repeatable measures of human-system interaction capability including robotic system mobility, dexterity, inspection, remote operator proficiency, and situational awareness. In particular, the operator control...

ASTM D8404-26a - Standard Practice for Preparation of Soil Samples by Ammonium Bifluoride-Nitric Acid Digestion for Subsequent Analysis for Metals and Metalloids
April 1, 2026 - ASTM International

5.1 There is a need to monitor the content of metals and metalloids to determine the presence of potential hazards. Hence, effective and efficient methods are required for the preparation of soil samples for determination of metals and metalloids present therein. 5.2 This practice may be used for...

Advertisement