1.1 This test method covers a laboratory procedure for the determination of aging effects of artificial weathering on latex sealants. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not...
3.1 Titanium dioxide is used in rubber compounding as a colorant to impart whiteness to any desired end product. It is used in sidewalls of automobile tires. 3.2 It is chemically inert and slightly basic with a pH of 7.0 to 8.0. The free-chalking, weathering properties of anatase...
1.1 This specification covers dry-cast hollow and solid nonloadbearing concrete masonry units machine-made from hydraulic cement, water, and suitable mineral aggregates with or without the inclusion of other materials. These units are intended for use in nonloadbearing partitions, but under certain...
5.1 The solar reflectance of a building envelope surface affects surface temperature and near-surface ambient air temperature. Surfaces with low solar reflectance absorb a high fraction of the incoming solar energy. Sunlight absorbed by a roof or by other building envelope surfaces can be conducted...
4.1 This test method is to be used in determining the absorption value of cast stone. Absorption is one measure of porosity of cast stone and, hence, its resistance to weathering and in-service durability.
1.1 This test method covers procedures for testing the durability of preassembled, permanently sealed vacuum insulating glass (VIG) units. 1.2 This test method is applicable only to VIG units that are constructed with flat glass lites (glass panes). 1.3 This test method is applicable to units made...
5.1 Photovoltaic modules and components must be resistant to prolonged exposure to solar radiation, moisture, and heat. Degradation of polymeric components, delamination at the encapsulant and other interfaces, and moisture ingress are among the degradation modes known to decrease the output of...
This specification covers brick intended for use in masonry and supplying structural or facing components, or both, to the structure. Bricks shall be classified according to their resistance to damage by freezing when saturated at a moisture content: Grade SW and Grade MW. The facing bricks shall...
4.1 Defacement of paint and coating films by fungal growth (mold, mildew) is a common phenomenon, and defacement by algal growth as referenced in Test Method D5589 can also occur under certain conditions. It is generally known that differences in the environment, lighting, temperature, humidity,...
3.1 These test methods are used to evaluate the properties of self-adhesive modified bituminous membranes. The results determine compliance with the applicable specifications, or they can be used for comparative analysis. 3.2 The test methods apply to "as manufactured" material and may not apply to...
This specification covers thin veneer brick units made from clay, shale, fire clay, sand, or mixtures thereof, and fired to incipient fusion for use in adhered or fastened veneer applications. The brick units shall be available in both Grades Interior and Exterior of the following types: Type TBS...
4.1 This guide is intended to provide information and guidance for designers, specifiers, manufacturers, contractors and users that are considering the use of prefabricated masonry elements. This guide identifies situations when prefabrication could be considered where other prefabricated systems...
6.1 The primary goal of this practice is to extract representative samples from PV modules for TCLP toxicity testing purposes in order to receive unbiased, comparable, and repeatable toxicity test results from independent TCLP testing laboratories. 6.2 Solar photovoltaic (PV) modules in the United...
4.1 This practice is intended to be used as a guide by those involved in the design of asphalt surface treatments. It covers typical application rates for the various types of surface treatments and covers aggregate sizes and recommended grades of asphaltic material for both hot and cool...
4.1 This test method describes the procedure to evaluate or compare, or both, the durability of sealants when subjected to accelerated weathering and cyclic movement in a joint. 4.2 Sealant installation procedures, design considerations and movement during cure affect the aging processes and...
This specification covers flexible sheet made from thermoplastic polyolefin (TPO) as the principal polymer, intended for use in single-ply roofing membranes exposed to the weather. The sheet shall contain reinforcing fabrics or scrims. The sheet shall be formulated from ethylene and higher...
5.1 During preconstruction and construction evaluations, use of these test methods establishes specific and overall performance characteristics for the mortar system. 5.2 Preconstruction testing of mortars prebatched by weight provides information for the selection of the individual mortar system...
3.1 Certain agencies who desire to use, store, or transport emulsified asphalt under less than ideal weather conditions may require that the product remain homogeneous (unbroken) after being subjected to a temperature of -18?°C. Note 1: The quality of the results produced by this standard...
5.1 These test methods are part of an overall suite of related test methods that provide repeatable measures of human-system interaction capability including robotic system mobility, dexterity, inspection, remote operator proficiency, and situational awareness. In particular, the operator control...
5.1 There is a need to monitor the content of metals and metalloids to determine the presence of potential hazards. Hence, effective and efficient methods are required for the preparation of soil samples for determination of metals and metalloids present therein. 5.2 This practice may be used for...
Narrow Your Results