1.1 This practice covers guidance for fire extinguishing agent concentration testing used in determining the distribution and concentration of fire extinguishing agents when discharged in an aircraft powerplant compartment. This practice is limited to vaporizing liquid fire extinguishing agents or...
1.1 These test methods provide various testing procedures commonly used for evaluating characteristics of concrete masonry units and related concrete units. Methods are provided for sampling, measurement of dimensions, compressive strength, absorption, unit weight (density), moisture content,...
1.1 This specification covers airworthiness requirements for establishing general limitations and information to be contained in the aeroplane flight manual. This specification specifies what information shall be provided and does not state how such information shall be presented unless this is...
1.1 This specification addresses airworthiness requirements for the design and installation of electric propulsion systems for aeroplanes. Hybrid-electric propulsion systems are addressed implicitly unless explicitly stated otherwise. This specification was written with the focus on electric...
5.1 Tensile properties determined by this test method are of value for the identification and characterization of materials for control and specification purposes. Tensile properties can vary with specimen thickness, method of preparation, speed of testing, type of grips used, and manner of...
1.1 This specification covers requirements for complying with the 14 CFR Part 23-64,or later/CS-23 Amendment 5, or later, regulations for ICA. This specification replaces the Instructions for Continued Airworthiness and Maintenance that was included in Specification F3117/F3117M. 1.2 An applicant...
This test method covers the procedures for the standard practice of performing magnetic particle examination of continuous grain flow crankshaft forgings intended for medium speed diesel engines. Crankshafts shall be divided into four zones of decreasing operational stress, each of which have been...
1.1 In harmony with the Joint Committee for Guides in Metrology (JCGM) and detection concepts of the International Union of Pure and Applied Chemistry (IUPAC) (1, 2), this test method uses a series of replicated measurements of an analyte at dosage levels giving instrumental responses that bracket...
1.1 This specification provides requirements for complying with the 14 CFR Part 23-64/CS-23 Amendment 5 or later regulations for Airplane Flight Manual (AFM). This Specification replaces the AFM requirements originally found in Specification F3117/F3117M. 1.2 An applicant intending to propose this...
1.1 This specification covers the material requirements for preformed polychloroprene elastomeric joint seals for concrete pavements. The seal consists of a multiple web design and functions only by compression of the seal between the faces of the joint with the seal folding inward at the...
1.1 This specification covers the material requirements for preformed polychloroprene elastomeric joint seals for bridges. The seal consists of a multiple-web design composed of polychloroprene and functions only by compression of the seal between the faces of the joint with the seal folding...
1.1 These test methods provide various testing procedures commonly used for evaluating characteristics of concrete masonry units and related concrete units. Methods are provided for sampling, measurement of dimensions, compressive strength, absorption, unit weight (density), moisture content,...
1.1 This specification covers international standards for the crew interface aspects of airworthiness and design for aircraft. "Crew" includes flight crew and maintenance crew. The material was developed through open consensus of international experts in general aviation. This information was...
1.1 This specification covers minimum requirements for the design of inflatable restraint systems for aircraft. The material was developed through open consensus of international experts in general aviation. This information was created by focusing on Level 1, 2, 3, and 4 Normal Category aeroplanes...
1.1 This specification covers international standards for the crew interface aspects of airworthiness and design for aircraft. "Crew" includes flight crew and maintenance crew. The material was developed through open consensus of international experts in general aviation. This information was...
1.1 This practice provides guidance for how an applicant can show compliance to the requirements for Warnings, Cautions, and Advisory Indications to the responsible crewmember. 1.2 An applicant intending to propose this information as Means of Compliance for a design approval must seek guidance...
1.1 This practice provides methods for how Enhanced Indications are provided to the responsible crewmember when an applicant uses these indications in support of compliance with the requirements for Stall Characteristics, Stall Warning, and Spins applicable to Normal Category Aeroplanes, using...
1.1 This specification covers the systems and equipment aspects of airworthiness and design for aircraft. The material was developed through open consensus of international experts in general aviation. This information was created by focusing on Level 1, 2, 3, and 4 Normal Category aeroplanes. The...
1.1 These test methods cover procedures for the sampling and testing of brick and structural clay tile. Although not necessarily applicable to all types of units, tests include modulus of rupture, compressive strength, absorption, saturation coefficient, effect of freezing and thawing,...
Narrow Your Results