1.1 These test methods cover the ability of window assemblies of various types to restrain, delay, or frustrate forced entry. 1.2 For purposes of these test methods, window assemblies are defined as described in 1.2.1 - 1.2.5 and as shown in Fig. 1. Window...
1.1 This test method covers a standard laboratory procedure for determining the air leakage rates of exterior windows, skylights, curtain walls, and doors under specified differential pressure conditions across the specimen. The test method described is for tests with...
This specification covers exterior windows, glazed curtain walls, doors and impact protective systems used in buildings located in geographic regions that are prone to hurricanes. The test specimens shall be Fenestration assemblies, and impact protective systems; which shall be...
1.1 This test method covers the evaluation of the static load resistance of an insect screen in its functional position in a window under load conditions prescribed by appropriate specifying authorities or when used as a design tool for manufacturers. 1.2 This test method is...
1.1 This specification describes the physical requirements for primary and secondary terrestrial nonconcentrator photovoltaic reference cells. A reference cell is defined as a device that meets the requirements of this specification and is calibrated in accordance with Test Method E1125 or...
1.1 This test method covers the determination of total oil and grease (TOG) that can be extracted from water or wastewater samples by cyclohexane and measured by non-dispersive IR spectroscopy from 1370?cm-1 to 1380?cm-1. Treating the extract with Florisil to remove polar substances prior to...
This specification establishes the installation, safety, performance, and labeling requirements for devices intended to address the risk of injury and death associated with accidental falls from windows by children five years old and younger. It applies to window fall prevention...
1.1 This specification covers performance requirements and methods of test for the resistance to forced entry of window and door assemblies. This specification addresses the capability of window and door assemblies to frustrate and potentially delay or deter opportunistic entry...
1.1 This classification covers rigid Poly(Vinyl Chloride)(PVC), Chlorinated Poly(Vinyl Chloride)(CPVC), copolymers, blends and alloys, and composite materials derived from recyclate from extruded, molded or calendared forms or operations and composed of polyvinyl chloride, chlorinated polyvinyl...
This document specifies a test method and corresponding performance requirements for saw chain shot protective windows on forestry machines equipped with a chain saw for cutting, harvesting or processing as defined in ISO 6814. It also applies to machines that have been modified to...
1.1 This specification establishes requirements for the material properties, including dimensional stability and extrusion quality, of rigid, poly(vinyl chloride) (PVC) interior-profile extrusions. Methods for identifying interior-profile extrusions that comply with the requirements of this...
3.1 Adjustment methods provide a means for combining the results of neutron transport calculations with neutron dosimetry measurements (see Test Method E1005 and NUREG/CR-5049) in order to obtain optimal estimates for neutron damage exposure parameters with assigned uncertainties. The...
1.1 This specification establishes requirements for composition, performance, and labeling of artists' pastels. 1.2 This specification includes requirements for identification and lightfastness. 1.3 Pastel specimens are exposed to both natural daylight through window glass and window...
1.1 This test method measures the performance of the perimeter fire barrier and its ability to maintain a seal to prevent fire spread during the deflection and deformation of the exterior wall assembly and floor assembly during the fire test, while resisting fire exposure from an...
1.1 This standard describes procedures for the determination of the relative lightfastness and weatherability of printed matter under the following conditions, which involve exposure to natural daylight or accelerated procedures in the laboratory: 1.1.1 Method 1-Daylight behind window glass,...
1.1 This test method is a general test procedure for load tests of glass subjected to uniform static loads. It is applicable for test protocols involving specified loads, load durations, and loading rates. 1.2 This test method is applicable to architectural flat...
1.1 This test method measures the performance of the perimeter fire barrier and its ability to maintain a seal to prevent fire spread during the deflection and deformation of the exterior wall assembly and floor assembly during the fire test, while resisting fire exposure from an...
1.1 These test methods, including a fire test response method, cover the apparatus, procedures, and acceptance conditions for evaluating the normal operational performance and the performance characteristics under assault conditions of detention glazing used in window and door...
Narrow Your Results