UNLIMITED FREE
ACCESS TO THE WORLD'S BEST IDEAS

SUBMIT
Already a GlobalSpec user? Log in.

This is embarrasing...

An error occurred while processing the form. Please try again in a few minutes.

Customize Your GlobalSpec Experience

Select Your Free Newsletters

Industry Newsletters

Select Your Free Product Alerts

Finish!
Privacy Policy

This is embarrasing...

An error occurred while processing the form. Please try again in a few minutes.

NPFC - A-A-59305

TERMINAL, STUD THREADED DOUBLE TURRET

active, Most Current
Buy Now
Organization: NPFC
Publication Date: 1 August 2019
Status: active
Page Count: 7
scope:

This commercial item description covers a double turret, threaded terminal stud for use on terminal boards.

Document History

A-A-59305
August 1, 2019
TERMINAL, STUD THREADED DOUBLE TURRET
This commercial item description covers a double turret, threaded terminal stud for use on terminal boards.
A-A-59305
December 2, 2014
Terminal, Stud Threaded Double Turret
A description is not available for this item.
A-A-59305
February 24, 2010
Terminal, Stud Threaded Double Turret
A description is not available for this item.
A-A-59305
May 11, 2005
TERMINAL, STUD THREADED DOUBLE TURRET
A description is not available for this item.
A-A-59305
April 15, 1999
TERMINAL, STUD THREADED DOUBLE TURRET
This commercial item description covers a double turret, threaded terminal stud for use on terminal boards.

References

This document references:
ASME B1.1 - Unified Inch Screw Threads (UN and UNR Thread Form)
Published by ASME on January 1, 2019
This Standard specifies the thread form, series, class, allowance, tolerance, and designation for unified screw threads. (In order to emphasize that unified screw threads are based on inch modules,...
This document references:
ASME Y14.5 - Dimensioning and Tolerancing
Published by ASME on January 1, 2018
INTRODUCTION This Standard establishes symbols, rules, definitions, requirements, defaults, and recommended practices for stating and interpreting dimensioning, tolerancing, and related requirements...
This document references:
ASTM B121/B121M - Standard Specification for Leaded Brass Plate, Sheet, Strip, and Rolled Bar
Published by ASTM on April 1, 2016
This specification establishes the requirements for leaded brass plate, sheet, strip, and rolled bar. Units—Values stated in either inch-pound units or SI units are to be regarded separately as...
This document references:
B140/B140M - Standard Specification for Copper-Zinc-Lead (Red Brass or Hardware Bronze) Rod, Bar, and Shapes
October 1, 2022
This specification establishes the requirements for copper-zinc-lead (leaded red brass or hardware bronze) rod, bar, and shapes of UNS Copper Alloy Nos. C31400, C31600, and C32000 available for...
This document references:
ASTM B16/B16M - Standard Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines
Published by ASTM on October 1, 2019
This specification establishes the requirements for freecutting brass rod, bar, wire, and shapes of any specified cross section produced from Copper Alloy UNS Nos. C36000 or C36010 suitable for...
This document references:
ASTM B545 - Standard Specification for Electrodeposited Coatings of Tin
Published by ASTM on May 1, 2013
This specification covers the requirements for electrodeposited (electroplated) coatings of tin applied to metallic articles. Tin coatings are used to provide a low contactresistance surface, to...
This document references:
ASTM B339 - Standard Specification for Pig Tin
Published by ASTM on November 1, 2019
This specification covers refined tin in pig form recovered and cast from primary and secondary tin-bearing materials. One grade of tin metal is specified and is designated by the grade letter shown...
View Less
View All
Advertisement