UNLIMITED FREE
ACCESS TO THE WORLD'S BEST IDEAS

SUBMIT
Already a GlobalSpec user? Log in.

This is embarrasing...

An error occurred while processing the form. Please try again in a few minutes.

Customize Your GlobalSpec Experience

Select Your Free Newsletters

Industry Newsletters

Select Your Free Product Alerts

Finish!
Privacy Policy

This is embarrasing...

An error occurred while processing the form. Please try again in a few minutes.

GMW15423

Performance Testing of Fuel Hoses

active, Most Current
Buy Now
Organization: GMW
Publication Date: 1 September 2019
Status: active
Page Count: 12
scope:

Purpose.

This test procedure describes performance tests for fuel and fuel filler hoses.

Document History

GMW15423
September 1, 2019
Performance Testing of Fuel Hoses
Purpose. This test procedure describes performance tests for fuel and fuel filler hoses.
GMW15423
August 1, 2016
Performance Testing of Fuel Hoses
Introduction Note: Nothing in this standard supercedes applicable laws and regulations. Note: In the event of conflict between the English and domestic language, the English language shall take...
GMW15423
October 1, 2011
Performance Testing of Fuel Hoses
Note: Nothing in this standard supersedes applicable laws and regulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence....
GMW15423
February 1, 2009
Performance Testing of Fuel Hoses
Note: Nothing in this standard supersedes applicable laws and regulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence....

References

This document references:
ASTM D3703 - Standard Test Method for Hydroperoxide Number of Aviation Turbine Fuels, Gasoline and Diesel Fuels
Published by ASTM on April 1, 2018
This test method covers the determination of the hydroperoxide content expressed as hydroperoxide number of aviation turbine, gasoline and diesel fuels. The range of hydroperoxide number included in...
This document references:
D4678 REV A - Standard Practice for Rubber—Preparation, Testing, Acceptance, Documentation, and Use of Reference Materials
July 1, 2015
This practice covers materials used on an industry-wide basis as reference materials, which are vitally important to conduct product, specification, and development testing in the rubber industry....
This document references:
D471 REV A - Standard Test Method for Rubber Property—Effect of Liquids
July 1, 2016
This test method covers the required procedures to evaluate the comparative ability of rubber and rubber-like compositions to withstand the effect of liquids. It is designed for testing: (1)...
This document references:
1817 - Rubber, vulcanized or thermoplastic — Determination of the effect of liquids
Published by ISO on June 1, 2022
This document describes methods of evaluating the resistance of vulcanized and thermoplastic rubbers to the action of liquids by measurement of properties of the rubbers before and after immersion in...
This document references:
ISO 188 - Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
Published by ISO on October 1, 2011
This International Standard specifies accelerated ageing or heat resistance tests on vulcanized or thermoplastic rubbers. Two methods are given: Method A: air-oven method using a cell-type oven or...
This document is referenced by:
GMW15349 - Low Permeability Fuel Filler Hose
Published by GMW on September 1, 2019
Purpose. This standard covers the material requirements of fuel filler and fuel filler vent hoses (coupled or uncoupled), for use with gasoline fuel in automotive fuel systems. Note: Fuel filler...
This document is referenced by:
GMW15605 - Fuel Filler Hose for Diesel and Biodiesel Fuels
Published by GMW on October 1, 2019
Material Description. This standard covers the material requirements of fuel filler and fuel filler vent hoses (coupled or uncoupled), for use with diesel fuel in automotive fuel systems. Note: Hoses...
This document is referenced by:
GMW16997 - Unreinforced, Non-Conductive Fuel Filler Hose
Published by GMW on December 1, 2019
Purpose. This specification covers construction of one (1) hose, 12.7 mm diameter and larger, coupled and uncoupled, for use with gasoline, oil or diesel fuel in automotive fuel systems. This hose is...
This document is referenced by:
GMW17862 - Material Specification for Transmission Venting Hoses Single and Double Layered
Published by GMW on April 1, 2020
Note: Nothing in this standard supercedes applicable laws and regulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence. This...
View Less
View All
Advertisement