UNLIMITED FREE
ACCESS TO THE WORLD'S BEST IDEAS

SUBMIT
Already a GlobalSpec user? Log in.

This is embarrasing...

An error occurred while processing the form. Please try again in a few minutes.

Customize Your GlobalSpec Experience

Select Your Free Newsletters

Industry Newsletters

Select Your Free Product Alerts

Finish!
Privacy Policy

This is embarrasing...

An error occurred while processing the form. Please try again in a few minutes.

SAE International - AS6194

FITTING ASSEMBLY, TEE, AXIALLY SWAGED, FEMALE FLARELESS ON THE RUN, AXIALLY SWAGED ON THE SIDE, HYDRAULIC, UP TO 1500 PSI

active
Buy Now
Organization: SAE International
Publication Date: 3 August 2011
Status: active

Document History

AS6194
August 3, 2011
FITTING ASSEMBLY, TEE, AXIALLY SWAGED, FEMALE FLARELESS ON THE RUN, AXIALLY SWAGED ON THE SIDE, HYDRAULIC, UP TO 1500 PSI
A description is not available for this item.

References

This document references:
AMS2700 - Passivation of Corrosion Resistant Steels
Published by SAE International on March 1, 2000
This specification defines the engineering requirements for a process to assure removal of free iron or other less noble contaminants from the surfaces of corrosion resistant steel parts.
This document references:
AMSQQA225/6 - ALUMINUM ALLOY, 2024, BAR, ROD, AND WIRE; ROLLED, DRAWN, OR COLD FINISHED
Published by SAE International on July 1, 1997
This specification covers the specific requirements for 2024 aluminum alloy bar, rod and wire produced by rolling, drawing or cold finishing.
This document references:
AMSQQA225/8 - ALUMINUM ALLOY 6061, BAR, ROD, WIRE, AND SPECIAL SHAPES; ROLLED, DRAWN, OR COLD FINISHED
Published by SAE International on July 1, 1997
This specification covers the specific requirements for 6061 aluminum alloy bar, rod, wire, and special shapes produced by rolling, drawing, or cold finishing.
This document references:
AMSQQA225/9 - Aluminum Alloy 7075, Bar, Rod, Wire, and Special Shapes; Rolled, Drawn, or Cold Finished
Published by SAE International on May 19, 2010
This specification covers the specific requirements for 7075 aluminum alloy bar, rod, wire, and special shapes produced by rolling, drawing, or cold finishing.
This document references:
AS4370 - NUT - SWIVEL, WIRED ON
Published by SAE International on June 7, 1991
A description is not available for this item.
This document references:
AS5272 - Lubricant, Solid Film, Heat Cured, Corrosion Inhibiting Procurement Specification
Published by SAE International on October 1, 2001
This SAE Aerospace specification establishes the requirements for heat cured solid film lubricants for aerospace fastener/threaded applications only. For other general or high temperature...
This document references:
AS5863 - FITTING END, 24° CONE, FLARELESS, FLUID CONNECTION, DESIGN STANDARD
Published by SAE International on January 9, 2013
A description is not available for this item.
This document references:
AS5864 - FITTING END, BULKHEAD, 24° CONE, FLARELESS, FLUID CONNECTION, DESIGN STANDARD
Published by SAE International on January 9, 2013
A description is not available for this item.
This document references:
AS6116 - Aluminum Fittings, Axially Swaged Tube with Flareless Separable, Fluid System Up to 1500 psi (10 340 kPa) Maximum, Specification for
Published by SAE International on November 9, 2011
This SAE Aerospace Standard (AS) establishes the requirements for externally swaged aluminum tube fittings on aluminum tubing with flareless separable fitting ends for use in hydraulic supply and...
This document references:
AS6124 - Aluminum Axially Swaged Fittings, Installation and Inspection Procedure
Published by SAE International on December 20, 2011
This procedure establishes the instructions to prepare tube ends, install and inspect axially swaged permanent tube fittings qualified to AS6116. This procedure is applicable when specified on the...
View Less
View All
Advertisement