loading
IIAR CO2 HANDBOOK - THE CO2 HANDBOOK
IIAR
A description is not available for this item.
ASTM D6846-02(2026) - Standard Practice for Preparing Prints of Paste Printing Inks with a Printing Gage
June 1, 2026 - ASTM International

4.1 Laboratory proofing of inks is necessary to establish a reproducible prediction of print appearance and performance properties, most of which are highly sensitive to ink film thickness. The apparatus described in this practice has found wide use for routine control proofing because it provides...

ASTM F433-02(2026) - Standard Practice for Evaluating Thermal Conductivity of Gasket Materials
June 1, 2026 - ASTM International

5.1 This practice is designed to compare related materials under controlled conditions and their ability to maintain a minimum amount of thermal conductance. Test results should be correlated with field results in order to predict heat transfer properties in particular applications. 5.2 This...

ASTM E1361-02(2026) - Standard Guide for Correction of Interelement Effects in X-Ray Spectrometric Analysis
April 1, 2026 - ASTM International

4.1 Accuracy in quantitative X-ray spectrometric analysis depends upon adequate accounting for interelement effects either through sample preparation or through mathematical correction procedures, or both. This guide is intended to serve as an introduction to users of X-ray fluorescence correction...

ASTM D3612-02(2026) - Standard Test Method for Analysis of Gases Dissolved in Electrical Insulating Oil by Gas Chromatography
January 1, 2026 - ASTM International

1.1 This test method covers three procedures for extraction and measurement of gases dissolved in electrical insulating oil having a viscosity of 20 cSt (100 SUS) or less at 40?°C (104?°F), and the identification and determination of the individual component gases extracted. Other methods have been...

ASTM B2-13(2026) - Standard Specification for Medium-Hard-Drawn Copper Wire
February 1, 2026 - ASTM International

1.1 This specification covers medium-hard-drawn round copper wire for electrical purposes (see Explanatory Note 1). 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information...

ASTM D6497/D6497M-02(2025) - Standard Guide for Mechanical Attachment of Geomembrane to Penetrations or Structures
December 1, 2025 - ASTM International

4.1 This guide attempts to detail specific areas of concern regarding the attachment of geomembranes to structures. Components of the geomembrane attachment are addressed as to the type and use of each component. 4.2 Although this guide does not address all aspects of geomembrane attachments, the...

ASTM D4620-02(2025) - Standard Test Method for Evaluating the Effective Surface Area of Zinc Oxide in Rubber
November 15, 2025 - ASTM International

4.1 The surface area of zinc-oxide in rubber can significantly affect cure activation and vulcanizate properties. 4.2 The specific surface area of zinc-oxide is usually measured by nitrogen absorption which requires the use of equipment not normally found in rubber laboratories. This test method...

ASTM D4570-02(2025) - Standard Test Method for Rubber Chemicals—Determination of Particle Size of Sulfur by Sieving (Dry)
November 1, 2025 - ASTM International

3.1 This test method is used to evaluate sulfur for suitability as a rubber vulcanizing agent. Sulfur particles must be small enough to dissolve in rubber during cure to produce a uniform network of cross-links. This test method is used as a quality control method to ensure that large particles are...

ASTM D4934-02(2025) - Standard Test Method for Rubber Compounding Materials: 2-Benzothiazyl Sulfenamide Accelerators—Insolubles
November 1, 2025 - ASTM International

4.1 Sulfenamides can degrade in chemical purity and functional performance, usually characterized by a drop in assay, a release of free amine, and an increase in insolubles. This test method may be used as an indication of such degradation. 4.2 Since MBTS (mercaptobenzothiazole disulfide) is a...

ASTM D5460-02(2025) - Standard Test Method for Rubber Compounding Materials—Water in Rubber Additives
November 1, 2025 - ASTM International

4.1 This test method is designed to determine the water content of various rubber accelerators. Since 2-mercaptobenzothiazole sulfenamide is hydrolytically unstable, the residual water content is an important characteristic.

ASTM D6798-02(2025) - Standard Terminology Relating to Flax and Linen
November 1, 2025 - ASTM International

1.1 This terminology covers definitions of technical terms related to flax and linen. 1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards,...

ASTM D6840-02(2025) - Standard Test Method for Effect of Drycleaning on Buttons
November 1, 2025 - ASTM International

5.1 This test method is useful for determining the change to the listed properties (see 1.1.1 and 1.1.2) and if the changes are acceptable for the intended use. This test may be used for acceptance testing of commercial shipments of buttons. 5.2 If there are differences of practical significance...

ASTM F1104-02(2025) - Standard Test Method for Preparing Aircraft Cleaning Compounds, Liquid Type, Water Base, for Storage Stability Testing
November 1, 2025 - ASTM International

4.1 This test method determines the procedure to be used to ensure the long term storage stability of aircraft cleaning and maintenance products, in order to ensure their ability to meet the shelf-life requirements called up in specifications or contract documents. The subsequent testing...

ASTM ISO/ASTM52911-2-19(2025) - Additive manufacturing — Design — Part 2: Laser-based powder bed fusion of polymers
October 1, 2025 - ASTM International

?This document specifies the features of laser-based powder bed fusion of polymers (LB-PBF-P) and provides detailed design recommendations. ?Some of the fundamental principles are also applicable to other additive manufacturing (AM) processes, provided that due consideration is given to...

ISUZU ISD-CO2-501 - HEXAGON HEAD BOLT AND WASHER ASSEMBLIES, PILOT POINT
ISUZU
A description is not available for this item.
ASTM D3314-02(2025) - Standard Test Method for Rubber—Chemical Analysis for Polystyrene Blocks In SBR (Styrene-Butadiene Rubber) and Styrene-Reinforced Latices
September 1, 2025 - ASTM International

4.1 This test method is suitable for manufacturing control, development, and research studies.

ASTM C1548-02(2025) - Standard Test Method for Dynamic Young's Modulus, Shear Modulus, and Poisson's Ratio of Refractory Materials by Impulse Excitation of Vibration
August 1, 2025 - ASTM International

4.1 This test method is nondestructive and is commonly used for material characterization and development, design data generation, and quality control purposes. The test assumes that the properties of the specimen are perfectly isotropic, which may not be true for some refractory materials. The...

ASTM D4288-02(2025) - Standard Specification for Calcium Borosilicate Pigments
July 1, 2025 - ASTM International

1.1 This specification covers three grades of pigment commercially known as calcium borosilicate composite pigment. The two types differ in chemical composition while the two classes of Type I differ in oil absorption. 1.2 This international standard was developed in accordance with internationally...

Advertisement