1.1 This specification covers wrought heat-resisting alloy UNS N08330 in the form of billets and bars only for reforging. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for...
1.1 This test method covers a laboratory procedure for conducting a single froth flotation test on fine coal (that is, nominal top size of 600 μm (No. 30 U.S.A. Standard Sieve Series) or finer) using a defined set of starting point conditions for the operating variables. 1.2 This test method does...
1.1 This specification covers rolled nickel-chromium-moly
1.1 This specification establishes minimum characteristics for those factors that determine particle size, consistency, purity, and ability to drain. 1.2 Engineered wood fiber that meets the requirements of this specification must comply with Specification F1292, if the surface is in the use zone...
1.1 This specification covers nickel-copper alloy UNS N04400 in the form of cold-worked seamless pipe and tube in the conditions shown in Table 1 and Table X1.1. 1.1.1 Hot worked material is available. Properties and permissible tolerances are to be agreed upon between the manufacturer and...
4.1 When choosing a thermal insulation product or combination of products, physical, chemical and mechanical properties and the significance of those properties should be considered. ASTM test methods are usually performed under laboratory conditions and may not accurately represent field...
1.1 This specification covers electrical contact components made from silver-molybdenum by powder metallurgical procedures. 1.2 This specification covers compositions within the silver-molybdenum system for electrical contact applications. 1.3 The values stated in either SI units or inch-pound...
1.1 This test method covers the effects of repeated insertion and withdrawal of separable electrical connectors which are harmful to the electrical performance of the connector. 1.2 This test method is limited to electrical connectors designed for use in applications where the current through any...
1.1 This test method covers a resistance probing test for detecting the presence of foreign matter on Printed Wiring Board (PWB) contacts or fingers that adversely affects electrical performance. This test method is defined specifically for such fingers coated with gold. Application of this test...
4.1 Management of asbestos-containing materials in buildings and facilities requires knowledge of the location, type, quantity, and condition of the material. The more complete and accurate the information available, the more appropriate and cost-effective are the control measures used to reduce...
1.1 This test method covers the determination of the distillation range of liquids boiling between 30?°C and 350?°C, that are chemically stable during the distillation process, by manual or automatic distillation procedures. 1.2 This test method is applicable to organic liquids such as...
1.1 These test methods cover the determination of the effect on physical properties of nonmetallic gasketing materials after immersion in test fluids. The types of materials covered are Type 1, Type 2, Type 3, and Type 7 as described in Classification F104. These test methods are not applicable to...
1.1 This specification2 covers rolled nickel-copper alloy (UNS N04400)3 plate, sheet, and strip. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not...
1.1 This test method covers the determination of the effects of heat and air on a film of semisolid asphaltic materials. The effects of this treatment are determined from measurements of selected asphalt properties before and after the test. 1.2 The values stated in either SI units or inch-pound...
1.1 This test method covers the determination of the effects of heat and air on a film of semisolid asphaltic materials. The effects of this treatment are determined from measurements of selected asphalt properties before and after the test. 1.2 The values stated in either SI units or inch-pound...
1.1 This test method covers the determination of flash points by the Tag open-cup apparatus of cutback asphalts having flash points of less than 93?°C [200?°F]. Note 1: Specifications commonly designate the Cleveland open cup (Test Method D92, IP?36) method for asphalt cements and cutback asphalts...
1.1 This specification2 covers welded, cold-worked, and annealed nickel-chromium-iron
1.1 This specification2 covers alloys UNS N08330 and UNS N08332 in the form of welded pipe intended for heat-resisting applications and general-corrosive service. 1.2 The pipe covered is nominal pipe sizes up to and including size 12, with the nominal wall thicknesses given as Schedules 5S, 10S,...
1.1 This specification covers nickel-copper-alumin
4.1 Ergonomics is the field concerned with designing physical spaces or workstations, equipment, tools, processes, procedures, and systems to accommodate the capabilities and limitations of human users. Pain, fatigue, or injuries may arise if there is a mismatch between the person's abilities and...
Narrow Your Results