loading
ASTM B512-20(2026) - Standard Specification for Nickel-Chromium-Silicon Alloy Billets and Bars
July 1, 2026 - ASTM International

1.1 This specification covers wrought heat-resisting alloy UNS N08330 in the form of billets and bars only for reforging. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for...

ASTM D5114/D5114M-90(2026) - Standard Test Method for Laboratory Froth Flotation of Coal in a Mechanical Cell
July 15, 2026 - ASTM International

1.1 This test method covers a laboratory procedure for conducting a single froth flotation test on fine coal (that is, nominal top size of 600 μm (No. 30 U.S.A. Standard Sieve Series) or finer) using a defined set of starting point conditions for the operating variables. 1.2 This test method does...

ASTM B443-26 - Standard Specification for Nickel-Chromium-Molybdenum-Columbium Alloy and Nickel-Chromium-Molybdenum-Silicon Alloy Plate, Sheet, and Strip
July 1, 2026 - ASTM International

1.1 This specification covers rolled nickel-chromium-molybdenum-columbium alloy (UNS N06625) and nickel-chromium-molybdenum-silicon alloy (UNS N06219) plate, sheet, and strip. 1.1.1 Alloy UNS N06625 products are furnished in two grades of different heat-treated conditions: 1.1.1.1 Grade 1...

ASTM F2075-26 - Standard Specification for Engineered Wood Fiber for Use as a Playground Safety Surface Under and Around Playground Equipment
June 1, 2026 - ASTM International

1.1 This specification establishes minimum characteristics for those factors that determine particle size, consistency, purity, and ability to drain. 1.2 Engineered wood fiber that meets the requirements of this specification must comply with Specification F1292, if the surface is in the use zone...

ASTM B165-26 - Standard Specification for Nickel-Copper Alloy Seamless Pipe and Tube
April 1, 2026 - ASTM International

1.1 This specification covers nickel-copper alloy UNS N04400 in the form of cold-worked seamless pipe and tube in the conditions shown in Table 1 and Table X1.1. 1.1.1 Hot worked material is available. Properties and permissible tolerances are to be agreed upon between the manufacturer and...

ASTM C1696-26 - Standard Guide for Industrial Thermal Insulation Systems
March 1, 2026 - ASTM International

4.1 When choosing a thermal insulation product or combination of products, physical, chemical and mechanical properties and the significance of those properties should be considered. ASTM test methods are usually performed under laboratory conditions and may not accurately represent field...

ASTM B662/B662M-26 - Standard Specification for Silver-Molybdenum Electrical Contact Material
February 1, 2026 - ASTM International

1.1 This specification covers electrical contact components made from silver-molybdenum by powder metallurgical procedures. 1.2 This specification covers compositions within the silver-molybdenum system for electrical contact applications. 1.3 The values stated in either SI units or inch-pound...

ASTM B794-97(2026) - Standard Test Method for Durability Wear Testing of Separable Electrical Connector Systems Using Electrical Resistance Measurements
February 1, 2026 - ASTM International

1.1 This test method covers the effects of repeated insertion and withdrawal of separable electrical connectors which are harmful to the electrical performance of the connector. 1.2 This test method is limited to electrical connectors designed for use in applications where the current through any...

ASTM B885-09(2026) - Standard Test Method for Presence of Foreign Matter on Printed Wiring Board Contacts
February 1, 2026 - ASTM International

1.1 This test method covers a resistance probing test for detecting the presence of foreign matter on Printed Wiring Board (PWB) contacts or fingers that adversely affects electrical performance. This test method is defined specifically for such fingers coated with gold. Application of this test...

ASTM E2356-26 - Standard Practice for Comprehensive Building Asbestos Surveys
February 1, 2026 - ASTM International

4.1 Management of asbestos-containing materials in buildings and facilities requires knowledge of the location, type, quantity, and condition of the material. The more complete and accurate the information available, the more appropriate and cost-effective are the control measures used to reduce...

ASTM D1078-11(2026) - Standard Test Method for Distillation Range of Volatile Organic Liquids
January 1, 2026 - ASTM International

1.1 This test method covers the determination of the distillation range of liquids boiling between 30?°C and 350?°C, that are chemically stable during the distillation process, by manual or automatic distillation procedures. 1.2 This test method is applicable to organic liquids such as...

ASTM F146-12(2025) - Standard Test Methods for Fluid Resistance of Gasket Materials
December 1, 2025 - ASTM International

1.1 These test methods cover the determination of the effect on physical properties of nonmetallic gasketing materials after immersion in test fluids. The types of materials covered are Type 1, Type 2, Type 3, and Type 7 as described in Classification F104. These test methods are not applicable to...

ASTM B127-25 - Standard Specification for Nickel-Copper Alloy Plate, Sheet, and Strip
November 1, 2025 - ASTM International

1.1 This specification2 covers rolled nickel-copper alloy (UNS N04400)3 plate, sheet, and strip. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not...

ASTM D1754/D1754M-20(2025) - Standard Test Method for Effects of Heat and Air on Asphaltic Materials (Thin-Film Oven Test)
November 1, 2025 - ASTM International

1.1 This test method covers the determination of the effects of heat and air on a film of semisolid asphaltic materials. The effects of this treatment are determined from measurements of selected asphalt properties before and after the test. 1.2 The values stated in either SI units or inch-pound...

ASTM D1754/D1754M-20(2025)e1 - Standard Test Method for Effects of Heat and Air on Asphaltic Materials (Thin-Film Oven Test)
November 1, 2025 - ASTM International

1.1 This test method covers the determination of the effects of heat and air on a film of semisolid asphaltic materials. The effects of this treatment are determined from measurements of selected asphalt properties before and after the test. 1.2 The values stated in either SI units or inch-pound...

ASTM D3143/D3143M-19(2025) - Standard Test Method for Flash Point of Cutback Asphalt with Tag Open-Cup Apparatus
November 1, 2025 - ASTM International

1.1 This test method covers the determination of flash points by the Tag open-cup apparatus of cutback asphalts having flash points of less than 93?°C [200?°F]. Note 1: Specifications commonly designate the Cleveland open cup (Test Method D92, IP?36) method for asphalt cements and cutback asphalts...

ASTM B517-25 - Standard Specification for Welded Nickel-Chromium-Iron-Alloy Pipe
July 1, 2025 - ASTM International

1.1 This specification2 covers welded, cold-worked, and annealed nickel-chromium-iron alloy (UNS N06600,3 N06603, N06025, and N06045) pipe for general corrosive service and heat-resisting applications. 1.2 This specification covers outside diameter and nominal wall pipe shown in ANSI B36.19. Pipe...

ASTM B710-20a(2025) - Standard Specification for Nickel-Iron-Chromium-Silicon Alloy Welded Pipe
July 1, 2025 - ASTM International

1.1 This specification2 covers alloys UNS N08330 and UNS N08332 in the form of welded pipe intended for heat-resisting applications and general-corrosive service. 1.2 The pipe covered is nominal pipe sizes up to and including size 12, with the nominal wall thicknesses given as Schedules 5S, 10S,...

ASTM B865-25 - Standard Specification for Precipitation Hardening Nickel-Copper-Aluminum Alloy Bar, Rod, Wire, Forgings, and Forging Stock
July 1, 2025 - ASTM International

1.1 This specification covers nickel-copper-aluminum alloy (UNS N05500) in the form of rounds, squares, hexagons, or rectangles, and forgings and forging stock, manufactured either by hot working or cold working, and cold-worked wire. 1.2 The values stated in inch-pound units are to be regarded as...

ASTM F3688-25 - Standard Guide for Evaluating Potential Ergonomic Risks From Exoskeleton Use
February 1, 2025 - ASTM International

4.1 Ergonomics is the field concerned with designing physical spaces or workstations, equipment, tools, processes, procedures, and systems to accommodate the capabilities and limitations of human users. Pain, fatigue, or injuries may arise if there is a mismatch between the person's abilities and...

Advertisement