1.1 This test method addresses the uniaxial compression of a double-notched test specimen to determine interlaminar shear strength of continuous fiber-reinforced ceramic composites (CFCCs) at elevated temperatures. Failure of the test specimen occurs by interlaminar shear between two centrally...
5.1 Significance of this Guide: 5.1.1 Continuous improvement (CI) is a fundamental element of an operation's quality management efforts. When CI is practiced daily from the top down through the organization, the other elements of quality management fall into place. 5.1.2 CI principles are not only...
5.1 According to statistics provided by the NFPA, one of the most common initiating events in a fatal fire is the dropping of a smoking material, such as a pre-roll, onto a bed or a piece of upholstered furniture. Test Methods E1352 and E1353 and NFPA 261 and NFPA 260 have been developed to...
5.1 Specimens tested using this standard, for example, duct silencers, are used to control sound propagation through ventilation ducts. The results gathered from testing specimens to this standard can be used to estimate the reduction in fan sound levels in ducted airflow systems caused by...
5.1 Phased array ultrasonic testing (PAUT) is an advanced examination technique used for enhanced flaw detection, sizing, and imaging as compared to conventional UT employing single-element transducers. PAUT utilizes multi-element (array) probes in which groups of elements are pulsed with...
5.1 Risk factors for work-related musculoskeletal disorders include lifting and carrying heavy loads, forced posture such as overhead work and repetitive tasks (2). The lower back, spine, and shoulder are frequently affected structures (3, 4). 5.2 This practice gives a standardized method for...
5.1 Risk factors for work-related musculoskeletal disorders include lifting and carrying heavy loads, forced posture such as overhead work, and repetitive tasks (2). The lower back, spine, and shoulder are frequently affected structures (3, 4). 5.2 This practice gives a standardized method for...
1.1 The purpose of this guide is to provide standard methods for the safe use of lithium ion (Li-ion) batteries onboard vessels. The guidelines in this document were developed primarily for larger Li-ion marine battery installations, such as for propulsion or ships service electrical power. The...
5.1 The most common initiating event in a fatal fire is the dropping of a cigarette onto a bed or piece of upholstered furniture, according to statistics provided by the National Fire Protection Association (4). Test Methods E1352 and E1353 and tests NFPA 261 and NFPA 260 have been developed to...
1.1 This practice covers two procedures for ultrasonic testing (UT) of flat panel (parallel surfaces) composites and flat sandwich core panels. Typical as-fabricated lay-ups include uniaxial, cross ply, and angle ply laminates, as well as honeycomb sandwich core materials. These procedures...
1.1 This test method describes the experimental methods and procedures for the determination of the critical mode I interlaminar strain energy release rate of continuous fiber- reinforced ceramic matrix composite (CMC) materials in terms of GIc. This property is also sometimes described as the mode...
1.1 This test method describes the experimental methods and procedures for the determination of the critical mode I interlaminar strain energy release rate of continuous fiber- reinforced ceramic matrix composite (CMC) materials in terms of GIc. This property is also sometimes described as the mode...
1.1 This test method covers the on-line and in-line determination of high-level turbidity in water that is greater than 1.0 turbidity units (TU) in municipal, industrial and environmental usage. 1.2 In principle, there are three basic applications for on-line measurement set ups. This first...
1.1 This guide covers the best practices for use of various turbidimeter designs for measurement of turbidity in waters including: drinking water, wastewater, industrial waters, and for regulatory and environmental monitoring. This guide covers both continuous and static measurements. 1.1.1 In...
5.1 This test practice is designed to produce tensile property data for material specifications, research and development, quality assurance, and structural design and analysis. Factors that influence the tensile response and should therefore be reported include the following: materials (laminates...
1.1 These requirements cover an energy storage system (ESS) that is intended to receive and store energy in some form so that the ESS can provide electrical energy to loads or to the local/area electric power system (EPS) when needed. Electrochemical, chemical, mechanical, and thermal ESS are...
1.1 This practice establishes procedures for matrix array ultrasonic testing (MAUT) of monolithic composites, composite sandwich constructions, and metallic test articles. These procedures can be used throughout the life cycle of a part during product and process design optimization, on line...
This Practice and the purchaser's PIP ELSAP04-D Data Sheet describe the minimum requirements for design, fabrication, inspection, testing, shipment, and documentation for a complete on-line, UPS system of either a pulse width modulated (PWM) or ferroresonant type. A PWM-type UPS...
1.1 These requirements cover battery systems as defined by this standard for use as energy storage for stationary applications such as for PV, wind turbine storage or for UPS, etc. applications. These systems shall be installed in accordance with NFPA 70, C22.1, or other applicable...
NOTE: This guide specification covers the requirements for static UPS to provide continuous ac power to critical loads and/or to improve the quality of ac power to critical loads. The specification is intended to cover three-phase systems starting with the smallest unit at 20 kVA. The upper...
Narrow Your Results