loading
ASTM E3474-25 - Standard Test Method for Measuring the Air Leakage Rate of the Building Envelope of an Individual Test Zone within a Multizone Building
August 1, 2025 - ASTM International

1.1 This test method provides a quantitative ?eld test procedure and calculation method for assessing an air leakage rate using fan-induced pressure differentials across the test envelope and the surrounding building, generated by multiple blower doors or equivalent equipment. 1.2 Building...

ASTM E1998-25 - Standard Guide for Assessing Depressurization-Induced Backdrafting and Spillage from Vented Combustion Appliances
February 1, 2025 - ASTM International

1.1 This guide describes and compares different methods for assessing the potential for, or existence of, depressurization-induced backdrafting and spillage from vented residential combustion appliances. 1.2 Assessment of depressurization-induced backdrafting and spillage is conducted under either...

UL 907 - Fireplace Accessories
September 4, 2024 - ULSE

Fireplace Accessories UL 907 1.1 These requirements apply to fireplace accessories that are intended only for field installation into or attachment to existing masonry fireplaces. Fireplace accessories include items such as heat exchangers, glass door assemblies, and the like. For the purpose of...

ASTM E3158-24 - Standard Test Method for Measuring the Air Leakage Rate of a Large or Multizone Building
July 1, 2024 - ASTM International

1.1 This standard test method covers a quantitative field-test procedure and calculation method for assessing an air leakage rate using a fan-induced pressure differential(s) across the building envelope, generated by blower doors or equivalent equipment. 1.2 Building setup conditions in...

UL 62841-4-6 - Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden Machinery - Safety - Part 4-6: Particular Requirements for Garden Blowers, Garden Vacuums and Garden Blower/Vacuums
September 29, 2023 - ULSE

IEC 62841-1:2014, Clause 1 is applicable, except as follows: Addition: This document applies to hand-held and backpack - garden blowers ; - garden vacuums ; and - garden blower/vacuums . This document does not apply to - walk-behind garden blowers , walk-behind garden vacuums...

ASTM F2361-18(2024) - Standard Guide for Ordering Low Voltage (1000 VAC or Less) Alternating Current Electric Motors for Shipboard Service—Up to and Including Motors of 500 Horsepower
May 1, 2024 - ASTM International

This guide provides the required basic ordering information for low voltage (1000 VAC or less, and up to and including motors of 500 hp) general-purpose (GP), commercial, universal, small and medium sized alternating current electric motors intended to drive common shipboard mechanical machinery...

UL 3300 - Service, Communication, Information, Education and Entertainment Robots - SCIEE Robots
May 14, 2024 - ULSE

These requirements cover the safety of the robotic function of Service, Communication, Information, Education and Entertainment (SCIEE) robots. These requirements supplement the safety requirements for the intended, non-robotic product function as described in the relevant identified standard(s)...

ASTM F2374-24 - Standard Practice for Design, Manufacture, Operation, and Maintenance of Inflatable Amusement Devices
May 15, 2024 - ASTM International

1.1 This practice establishes criteria for the Design, Manufacture, Installation, Operation, Maintenance, Inspection, Training, Auditing and Major Modification of commercial use Inflatable Amusement Devices. These devices are made of flexible fabric, inflated by one or more blowers, and rely...

J3109_202306 - PWM HVAC Blower Controller and BLDC Motor Controller Efficiency Assessment
June 13, 2023 - SAE International

The intention of this standard is to establish a framework to measure the efficiency of PWM HVAC Blower Controllers and Brushless DC Motor Controllers and define a usage based overall efficiency. This result can then be used by vehicle OEMs to demonstrate compliance towards requirements or...

ASTM E1554/E1554M-13(2023) - Standard Test Methods for Determining Air Leakage of Air Distribution Systems by Fan Pressurization
October 1, 2023 - ASTM International

5.1 Air leakage between an air distribution system and unconditioned spaces affects the energy losses from the distribution system, the ventilation rate of the building, and the entry rate of air pollutants. 5.2 The determination of infiltration energy loads and ventilation rates of residences and...

ASTM E1827-22 - Standard Test Methods for Determining Airtightness of Buildings Using an Orifice Blower Door
October 1, 2022 - ASTM International

1.1 These test methods describe two techniques for measuring air leakage rates through a building envelope in buildings that may be configured to a single zone. Both techniques use an orifice blower door to induce pressure differences across the building envelope and to measure those...

J169_202307 - Design Guidelines for Air-Conditioning Systems for Off-Road Operator Enclosures
July 10, 2023 - SAE International

The purpose of this document is to establish air-conditioning design guidelines that will apply to most systems rather than the specific design of any particular system. Operating conditions and characteristics of the equipment will determine the design of any successful system; since these...

UL 1917 - Solid-State Fan Speed Controls
June 17, 2022 - ULSE

1.1 These requirements cover solid state speed controls rated 300 volts or less, single phase, intended to be connected to 15 - 20 ampere branch circuits and intended to be installed in accordance with the National Electrical Code, ANSI/NFPA 70 and used with: a) Fans and blowers that...

ASTM F2374-22 - Standard Practice for Design, Manufacture, Operation, and Maintenance of Inflatable Amusement Devices
September 1, 2022 - ASTM International

1.1 This practice establishes criteria for the Design, Manufacture, Installation, Operation, Maintenance, Inspection, Training, Auditing and Major Modification of commercial use Inflatable Amusement Devices. These devices are made of flexible fabric, inflated by one or more blowers, and rely...

UL 60335-2-69 - Household and Similar Electrical Appliances - Safety - Part 2-69: Particular Requirements for Wet and Dry Vacuum Cleaners, including Power Brush, for Commercial Use
March 25, 2022 - ULSE

This clause of Part 1 is replaced by the following. This part of IEC 60335 deals with the safety of electrical motor-operated vacuum cleaners, including back-pack vacuum cleaners , and dust extractors , for wet suction, dry suction, or wet and dry suction, intended for commercial indoor or outdoor...

ASTM D4167-21 - Standard Specification for Fiber-Reinforced Plastic Fans and Blowers
September 1, 2021 - ASTM International

This specification covers the minimum requirements for construction of fiber-reinforced thermoset plastic fans (both centrifugal and axial) and blowers, and provides for a common basis for determining safe operating speeds. The fan housing shall be of laminate construction consisting of a...

ASTM F2332-06(2022) - Standard Specification for Annular Ball Bearings for Instruments and Precision Rotating Components
January 1, 2022 - ASTM International

1.1 This specification covers annular ball bearings intended primarily for use in instrument and precision rotating components. Instrument and precision ball bearings should meet tolerances specified in ABMA Standard 12.2, Instrument Ball Bearings Inch Design for Classes ABEC 5P and 7P. 1.2...

DS/ISO 22868 - Forestry and gardening machinery – Noise test code for portable hand-held machines with internal combustion engine – Engineering method (Grade 2 accuracy)
January 28, 2021 - DS

This document specifies a noise test code for determining, efficiently and under standardized conditions, the common noise emission characteristics of portable, hand-held, combustion engine powered forest and garden machines, and specific requirements for chain-saws, brush-cutters, grass-trimmers,...

ISO 22868 - Forestry and gardening machinery — Noise test code for portable handheld machines with internal combustion engine — Engineering method (Grade 2 accuracy)
January 1, 2021 - ISO

This document specifies a noise test code for determining, efficiently and under standardized conditions, the common noise emission characteristics of portable, hand-held, combustion engine powered forest and garden machines, and specific requirements for chain-saws, brush-cutters, grass-trimmers,...

ASTM F2374-21a - Standard Practice for Design, Manufacture, Operation, and Maintenance of Inflatable Amusement Devices
June 15, 2021 - ASTM International

1.1 This practice establishes criteria for the Design, Manufacture, Installation, Operation, Maintenance, Inspection, Training, Auditing and Major Modification of commercial use Inflatable Amusement Devices. These devices are made of flexible fabric, inflated by one or more blowers, and rely...

Advertisement