1.1 This test method provides a quantitative ?eld test procedure and calculation method for assessing an air leakage rate using fan-induced pressure differentials across the test envelope and the surrounding building, generated by multiple blower doors or equivalent equipment. 1.2 Building...
1.1 This guide describes and compares different methods for assessing the potential for, or existence of, depressurization-ind
Fireplace Accessories UL 907 1.1 These requirements apply to fireplace accessories that are intended only for field installation into or attachment to existing masonry fireplaces. Fireplace accessories include items such as heat exchangers, glass door assemblies, and the like. For the purpose of...
1.1 This standard test method covers a quantitative field-test procedure and calculation method for assessing an air leakage rate using a fan-induced pressure differential(s) across the building envelope, generated by blower doors or equivalent equipment. 1.2 Building setup conditions in...
IEC 62841-1:2014, Clause 1 is applicable, except as follows: Addition: This document applies to hand-held and backpack - garden blowers ; - garden vacuums ; and - garden blower/vacuums . This document does not apply to - walk-behind garden blowers , walk-behind garden vacuums...
This guide provides the required basic ordering information for low voltage (1000 VAC or less, and up to and including motors of 500 hp) general-purpose (GP), commercial, universal, small and medium sized alternating current electric motors intended to drive common shipboard mechanical machinery...
These requirements cover the safety of the robotic function of Service, Communication, Information, Education and Entertainment (SCIEE) robots. These requirements supplement the safety requirements for the intended, non-robotic product function as described in the relevant identified standard(s)...
1.1 This practice establishes criteria for the Design, Manufacture, Installation, Operation, Maintenance, Inspection, Training, Auditing and Major Modification of commercial use Inflatable Amusement Devices. These devices are made of flexible fabric, inflated by one or more blowers, and rely...
The intention of this standard is to establish a framework to measure the efficiency of PWM HVAC Blower Controllers and Brushless DC Motor Controllers and define a usage based overall efficiency. This result can then be used by vehicle OEMs to demonstrate compliance towards requirements or...
5.1 Air leakage between an air distribution system and unconditioned spaces affects the energy losses from the distribution system, the ventilation rate of the building, and the entry rate of air pollutants. 5.2 The determination of infiltration energy loads and ventilation rates of residences and...
1.1 These test methods describe two techniques for measuring air leakage rates through a building envelope in buildings that may be configured to a single zone. Both techniques use an orifice blower door to induce pressure differences across the building envelope and to measure those...
The purpose of this document is to establish air-conditioning design guidelines that will apply to most systems rather than the specific design of any particular system. Operating conditions and characteristics of the equipment will determine the design of any successful system; since these...
1.1 These requirements cover solid state speed controls rated 300 volts or less, single phase, intended to be connected to 15 - 20 ampere branch circuits and intended to be installed in accordance with the National Electrical Code, ANSI/NFPA 70 and used with: a) Fans and blowers that...
1.1 This practice establishes criteria for the Design, Manufacture, Installation, Operation, Maintenance, Inspection, Training, Auditing and Major Modification of commercial use Inflatable Amusement Devices. These devices are made of flexible fabric, inflated by one or more blowers, and rely...
This clause of Part 1 is replaced by the following. This part of IEC 60335 deals with the safety of electrical motor-operated vacuum cleaners, including back-pack vacuum cleaners , and dust extractors , for wet suction, dry suction, or wet and dry suction, intended for commercial indoor or outdoor...
This specification covers the minimum requirements for construction of fiber-reinforced thermoset plastic fans (both centrifugal and axial) and blowers, and provides for a common basis for determining safe operating speeds. The fan housing shall be of laminate construction consisting of a...
1.1 This specification covers annular ball bearings intended primarily for use in instrument and precision rotating components. Instrument and precision ball bearings should meet tolerances specified in ABMA Standard 12.2, Instrument Ball Bearings Inch Design for Classes ABEC 5P and 7P. 1.2...
This document specifies a noise test code for determining, efficiently and under standardized conditions, the common noise emission characteristics of portable, hand-held, combustion engine powered forest and garden machines, and specific requirements for chain-saws, brush-cutters, grass-trimmers,...
This document specifies a noise test code for determining, efficiently and under standardized conditions, the common noise emission characteristics of portable, hand-held, combustion engine powered forest and garden machines, and specific requirements for chain-saws, brush-cutters, grass-trimmers,...
1.1 This practice establishes criteria for the Design, Manufacture, Installation, Operation, Maintenance, Inspection, Training, Auditing and Major Modification of commercial use Inflatable Amusement Devices. These devices are made of flexible fabric, inflated by one or more blowers, and rely...
Narrow Your Results