1.1 These test methods describe the determination of the water vapor content of electrical insulating gases by directly or indirectly measuring the dew point and calculating the water vapor content. 1.2 The following three test methods are provided: 1.2.1 Method A describes the automatic chilled...
4.1 Geomembranes are used as barriers to prevent liquids from leaking from landfills, ponds, and other containments. For this purpose, it is desirable that the geomembrane have as little leakage as practical. 4.2 The liquids may contain contaminants which, if released, can cause damage to the...
5.1 Need for Heat Flux Measurements: 5.1.1 Independent measurements of temperature and heat flux support the development and validation of engineering models of fires and other high environments, such as furnaces. For tests of fire protection materials and structural assemblies, temperature and...
This specification covers the electrical, visual, and physical properties of natural blocks and films made from mica that are suitable for use in fixed mica-dielectric capacitors. The materials under this specification are of three forms and four classes. Samples should be taken and tested...
1.1 This test method covers the determination of the thickness of plastic film, ranging in thickness from 2.5 to 250 μm, with a non-contact thickness gauge that uses capacitance-based technology. It includes a method to generate a series of thickness data points that can be used to...
1.1 These test methods cover two bridge techniques for measuring the energy and integrated charge of pulse and pseudoglow partial discharges: 1.2 Test Method A makes use of capacitance and loss characteristics such as measured by the transformer ratio-arm bridge or the high-voltage Schering...
1.1 This test method covers the classifying and counting of faults in spun yarns using capacitance testers. 1.1.1 Protruding fibers or yarn hairiness, or both, are not determined as part of this method. Note 1: For measuring protruding fibers or hairiness, or both, refer to Guide D5647. 1.2...
4.1 This testing is performed to determine the electrical contact reliability under switching conditions and the physical changes caused by mechanical actuation of the switch assembly in the environments in which the assemblies operate. Evidence of deterioration, that is, cracking of substrate,...
1.1 This test method covers determination of the coefficient of linear thermal expansion for plastic materials having coefficients of expansion greater than 1?μm/(m.°C) by use of a vitreous silica dilatometer. At the test temperatures and under the stresses imposed, the plastic materials shall have...
This specification covers the requirements for electrical liquid level indicating equipment for shipboard low pressure and high pressure tanks containing freshwater, feed water, potable water, seawater, wastewater, diesel fuel, lubricating oil, contaminated oil, refrigerants, JP fuels, and various...
4.1 Dissipation Factor (or Power Factor)-This is a measure of the dielectric losses in an electrical insulating liquid when used in an alternating electric field and of the energy dissipated as heat. A low dissipation factor or power factor indicates low ac dielectric losses. Dissipation factor or...
3.1 This test method can be utilized to verify the performance of polarization resistance measurement equipment including reference electrodes, electrochemical cells, potentiost- ats, scan generators, and measuring and recording devices. The test method is also useful for training operators in...
5.1 Design calculations for radio frequency (RF), microwave, and millimetre-wave components require the knowledge of values of complex permittivity and permeability at operating frequencies. This test method is useful for evaluating small experimental batch or continuous production materials used...
5.1 Design calculations for radio frequency (RF), microwave, and millimetre-wave components require the knowledge of values of complex permittivity and permeability at operating frequencies. This test method is useful for evaluating small experimental batch or continuous production materials used...
5.1 Permittivity-Insulat
1.1 This practice applies to techniques that use nondestructive electrical impedance (EI) scanners to locate moisture and evaluate the comparative moisture content within insulated low-slope roofing and waterproofing systems. 1.2 This practice is applicable to roofing and waterproofing systems...
1.1 This practice applies to techniques that use nondestructive electrical impedance (EI) scanners to locate moisture and evaluate the comparative moisture content within insulated low-slope roofing and waterproofing systems. 1.2 This practice is applicable to roofing and waterproofing systems...
1.1 This part of IEC 60079 standard gives requirements for the design, construction, assessment, verification and marking of rooms used to protect internal equipment: - a located in a Zone 1 or Zone 2 or Zone 21 or Zone 22 explosive atmosphere (an area normally requiring an equipment protection...
This document describes a method, using capacitance measuring equipment, for determining the unevenness of linear density along the length of textile strands. The method is applicable to tops, slivers, rovings, spun yarns and continuous filament yarns, made from either natural or man-made...
1.1 These test methods cover two bridge techniques for measuring the energy and integrated charge of pulse and pseudoglow partial discharges: 1.2 Test Method A makes use of capacitance and loss characteristics such as measured by the transformer ratio-arm bridge or the high-voltage Schering...
Narrow Your Results