loading
ASTM D2029-26 - Standard Test Methods for Water Vapor Content of Electrical Insulating Gases by Measurement of Dew Point
January 1, 2026 - ASTM International

1.1 These test methods describe the determination of the water vapor content of electrical insulating gases by directly or indirectly measuring the dew point and calculating the water vapor content. 1.2 The following three test methods are provided: 1.2.1 Method A describes the automatic chilled...

ASTM D7240-25 - Standard Practice for Electrical Leak Location Using Geomembranes with an Insulating Layer in Intimate Contact with a Conductive Layer via Electrical Capacitance Technique (Conductive-Backed Geomembrane Spark Test)
December 1, 2025 - ASTM International

4.1 Geomembranes are used as barriers to prevent liquids from leaking from landfills, ponds, and other containments. For this purpose, it is desirable that the geomembrane have as little leakage as practical. 4.2 The liquids may contain contaminants which, if released, can cause damage to the...

ASTM E3057-26 - Standard Test Method for Measuring Heat Flux Using Directional Flame Thermometers with Advanced Data Analysis Techniques
January 1, 2026 - ASTM International

5.1 Need for Heat Flux Measurements: 5.1.1 Independent measurements of temperature and heat flux support the development and validation of engineering models of fires and other high environments, such as furnaces. For tests of fire protection materials and structural assemblies, temperature and...

ASTM D748-18(2025) - Standard Specification for Natural Block Mica and Mica Films Suitable for Use in Fixed Mica-Dielectric Capacitors
September 1, 2025 - ASTM International

This specification covers the electrical, visual, and physical properties of natural blocks and films made from mica that are suitable for use in fixed mica-dielectric capacitors. The materials under this specification are of three forms and four classes. Samples should be taken and tested...

ASTM D8136-24 - Standard Test Method for Determining Plastic Film Thickness and Thickness Variability Using a Non-Contact Capacitance Thickness Gauge
December 1, 2024 - ASTM International

1.1 This test method covers the determination of the thickness of plastic film, ranging in thickness from 2.5 to 250 μm, with a non-contact thickness gauge that uses capacitance-based technology. It includes a method to generate a series of thickness data points that can be used to...

ASTM D3382-24 - Standard Test Methods for Measurement of Energy and Integrated Charge Transfer Due to Partial Discharges (Corona) Using Bridge Techniques
December 1, 2024 - ASTM International

1.1 These test methods cover two bridge techniques for measuring the energy and integrated charge of pulse and pseudoglow partial discharges: 1.2 Test Method A makes use of capacitance and loss characteristics such as measured by the transformer ratio-arm bridge or the high-voltage Schering...

ASTM D6197-99(2024) - Standard Test Method for Classifying and Counting Faults in Spun Yarns in Electronic Tests
November 1, 2024 - ASTM International

1.1 This test method covers the classifying and counting of faults in spun yarns using capacitance testers. 1.1.1 Protruding fibers or yarn hairiness, or both, are not determined as part of this method. Note 1: For measuring protruding fibers or hairiness, or both, refer to Guide D5647. 1.2...

ASTM F1578-24 - Standard Test Method for Contact Closure Cycling of a Membrane Switch
May 15, 2024 - ASTM International

4.1 This testing is performed to determine the electrical contact reliability under switching conditions and the physical changes caused by mechanical actuation of the switch assembly in the environments in which the assemblies operate. Evidence of deterioration, that is, cracking of substrate,...

ASTM D696-24 - Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between -30°C and +30°C with a Vitreous Silica Dilatometer
August 1, 2024 - ASTM International

1.1 This test method covers determination of the coefficient of linear thermal expansion for plastic materials having coefficients of expansion greater than 1?μm/(m.°C) by use of a vitreous silica dilatometer. At the test temperatures and under the stresses imposed, the plastic materials shall have...

ASTM F2044-09(2024) - Standard Specification for Liquid Level Indicating Equipment, Electrical
May 1, 2024 - ASTM International

This specification covers the requirements for electrical liquid level indicating equipment for shipboard low pressure and high pressure tanks containing freshwater, feed water, potable water, seawater, wastewater, diesel fuel, lubricating oil, contaminated oil, refrigerants, JP fuels, and various...

ASTM D924-23 - Standard Test Method for Dissipation Factor (or Power Factor) and Relative Permittivity (Dielectric Constant) of Electrical Insulating Liquids
December 1, 2023 - ASTM International

4.1 Dissipation Factor (or Power Factor)-This is a measure of the dielectric losses in an electrical insulating liquid when used in an alternating electric field and of the energy dissipated as heat. A low dissipation factor or power factor indicates low ac dielectric losses. Dissipation factor or...

ASTM G59-23 - Standard Test Method for Conducting Potentiodynamic Polarization Resistance Measurements
June 1, 2023 - ASTM International

3.1 This test method can be utilized to verify the performance of polarization resistance measurement equipment including reference electrodes, electrochemical cells, potentiost- ats, scan generators, and measuring and recording devices. The test method is also useful for training operators in...

ASTM D7449/D7449M-22a - Standard Test Method for Measuring Relative Complex Permittivity and Relative Magnetic Permeability of Solid Materials at Microwave Frequencies Using Coaxial Air Line
September 1, 2022 - ASTM International

5.1 Design calculations for radio frequency (RF), microwave, and millimetre-wave components require the knowledge of values of complex permittivity and permeability at operating frequencies. This test method is useful for evaluating small experimental batch or continuous production materials used...

ASTM D5568-22a - Standard Test Method for Measuring Relative Complex Permittivity and Relative Magnetic Permeability of Solid Materials at Microwave Frequencies Using Waveguide
September 1, 2022 - ASTM International

5.1 Design calculations for radio frequency (RF), microwave, and millimetre-wave components require the knowledge of values of complex permittivity and permeability at operating frequencies. This test method is useful for evaluating small experimental batch or continuous production materials used...

ASTM D150-22 - Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation
September 1, 2022 - ASTM International

5.1 Permittivity-Insulating materials are used in general in two distinct ways, (1) to support and insulate components of an electrical network from each other and from ground, and (2) to function as the dielectric of a capacitor. For the first use, it is generally desirable to have the...

ASTM D7954/D7954M-22a - Standard Practice for Moisture Surveying of Roofing and Waterproofing Systems Using Nondestructive Electrical Impedance Scanners
May 1, 2022 - ASTM International

1.1 This practice applies to techniques that use nondestructive electrical impedance (EI) scanners to locate moisture and evaluate the comparative moisture content within insulated low-slope roofing and waterproofing systems. 1.2 This practice is applicable to roofing and waterproofing systems...

ASTM D7954/D7954M-22 - Standard Practice for Moisture Surveying of Roofing and Waterproofing Systems Using Nondestructive Electrical Impedance Scanners
April 15, 2022 - ASTM International

1.1 This practice applies to techniques that use nondestructive electrical impedance (EI) scanners to locate moisture and evaluate the comparative moisture content within insulated low-slope roofing and waterproofing systems. 1.2 This practice is applicable to roofing and waterproofing systems...

UL 60079-13 - Explosive Atmospheres - Part 13: Equipment Protection by Pressurized Room
June 27, 2022 - ULSE

1.1 This part of IEC 60079 standard gives requirements for the design, construction, assessment, verification and marking of rooms used to protect internal equipment: - a located in a Zone 1 or Zone 2 or Zone 21 or Zone 22 explosive atmosphere (an area normally requiring an equipment protection...

ISO 16549 - Textiles — Unevenness of textile strands — Capacitance method
January 1, 2021 - ISO

This document describes a method, using capacitance measuring equipment, for determining the unevenness of linear density along the length of textile strands. The method is applicable to tops, slivers, rovings, spun yarns and continuous filament yarns, made from either natural or man-made...

ASTM D3382-22 - Standard Test Methods for Measurement of Energy and Integrated Charge Transfer Due to Partial Discharges (Corona) Using Bridge Techniques
January 1, 2022 - ASTM International

1.1 These test methods cover two bridge techniques for measuring the energy and integrated charge of pulse and pseudoglow partial discharges: 1.2 Test Method A makes use of capacitance and loss characteristics such as measured by the transformer ratio-arm bridge or the high-voltage Schering...

Advertisement