loading
ASTM CARBON - ASTM STANDARDS ON ACTIVATED CARBON 2ND EDITION
ASTM
A description is not available for this item.
SPI FIBERGLASS PANELS - FIBERGLASS REINFORCED PANELS, REC INSTALL PRACTICE
SPI
A description is not available for this item.
AWWA FIBERGLASS SET - AWWA FIBERGLASS SET
AWWA
A description is not available for this item.
ASTM B1012/B1012M-26 - Standard Specification for Shaped Wire Compact Concentric-Lay-Stranded Aluminum Conductors, Carbon Fiber Composite Supported (ACCFCS/TW)
May 1, 2026 - ASTM International

1.1 This specification covers shaped wire compact concentric-lay-stranded aluminum conductors, Carbon Fiber Composite (CFC) supported (ACCFCS/TW) for use as overhead electrical conductors. (See X1.1). 1.2 The values stated in either SI units or inch-pound units are to be regarded...

ASTM B987/B987M-25 - Standard Specification for Carbon Fiber Thermoset Polymer Matrix Composite Core (CFC) for use in Overhead Electrical Conductors
September 1, 2025 - ASTM International

1.1 This specification covers carbon fiber reinforced thermoset matrix composite core strength members for use in reinforcing or supporting overhead electrical conductors. 1.2 This specification covers carbon fiber core diameters from 0.180?in. to 0.835 in. [4.57?mm to...

ASTM D4102/D4102M-22 - Standard Test Method for Thermal Oxidative Resistance of Carbon Fibers
May 1, 2022 - ASTM International

5.1 The test is used to determine the oxidative resistances of carbon fibers as a means of selecting the most stable fibers for incorporation in high-temperature fiber-reinforced composite systems. It can be used for quality control, material specification, and for...

ASTM D3531/D3531M-24 - Standard Test Method for Resin Flow of Carbon Fiber-Epoxy Prepreg
May 1, 2024 - ASTM International

5.1 This test method is used to obtain the resin flow of carbon fiber-epoxy prepreg tape, fabric or sheet material. It is suitable for comparing batches of material of supposedly the same characteristics and also for comparative evaluation of materials produced by different vendors...

GMW17180 - Polyamide 6 - Carbon Fiber Reinforced, Heat Stabilized, Weatherable, Compression Moldable
November 1, 2019 - GMW

Material Description. This specification describes Carbon Fiber (CF) reinforced, heat stabilized, weatherable Polyamide 6 (PA6), i.e., Nylon 6, which is used in compression moldable components. Symbols. The material abbreviations according to ISO 11469 are shown in Table 1....

FORD FLTM BO 134-01 - BURN-OFF METHOD FOR CARBON FIBER DETERMINATION
September 22, 2016 - FORD

Application This procedure is used to determine the percent carbon fiber by burning off the polymer matrix and calculating the remaining ash percent. This procedure assumes only carbon fiber is present in the material.

Carbon Fibers: Formation, Structure, and Properties
November 29, 2017 - CRC

Carbon Fibers presents an up-to-date review of the progress pertaining to the formation of carbon fibers from rayon, acrylic, and pitch precursors. The book emphasizes the preparation, characterization, and properties of commercial materials. It also considers the...

AMS2980/5A - Carbon Fiber Fabric and Epoxy Resin Wet Lay-Up Repair Material Part 5 - Carbon Fiber Fabrics, Plain Weave, 193 g/m2, and Epoxy Resin
September 24, 2021 - SAE International

This Material Specification defines the requirements of carbon fiber fabric and epoxy resin systems used for wet lay-up repair of carbon fiber reinforced epoxy structures, qualified according to AMS2980/1 and AMS2980/2. Unless otherwise specified by the drawing, the...

AMS2980/2B - Carbon Fiber Fabric and Epoxy Resin Wet Lay-up Repair Material Part 2 - Qualification Program
September 24, 2021 - SAE International

AMS2980/2 gives specific information about the qualification program for carbon fiber fabric, epoxy systems and the material combination used for wet lay-up repair of carbon fiber reinforced epoxy structures.

AMS2980/1B - Carbon Fiber Fabric and Epoxy Resin Wet Lay-Up Repair Material Part 1 - General Requirements
September 23, 2021 - SAE International

AMS2980/1 gives information about the technical requirements and qualification procedure for carbon fiber fabric and epoxy resin systems used for wet lay-up repair of carbon fiber reinforced epoxy structures.

GMW16519 - Procedure for the Manufacture of Carbon Fiber Sediment
January 1, 2018 - GMW

Introduction Note: Nothing in this standard supercedes applicable laws and regulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence. Purpose. Produce representative friction material debris for transmission controls testing....

AMS6885/2 - Unidirectional Carbon Fiber Tape Epoxy Repair Prepreg, Vacuum Curing Part 2 - Qualification Program for Fiber, Carbon Fiber Tape Prepreg, and Film Adhesive
February 23, 2021 - SAE International

AMS6885/2 gives specific information about the qualification program for unidirectional carbon fiber tape epoxy repair prepreg capable of curing under vacuum for repair of carbon fiber reinforced epoxy structures. The prepreg system shall include an epoxy film adhesive...

AMS2980/3B - Carbon Fiber Fabric and Epoxy Resin Wet Lay-Up Repair Material Part 3 - Purchasing Specification - Fabric
September 24, 2021 - SAE International

This PS, AMS2980/3, specifies the batch release and delivery requirements for carbon fiber and carbon fabric used for wet lay-up repair purposes.

ARP1674A - Automated Manufacture of Continuous Multi-Ply Carbon Fiber/Epoxy Resin Impregnated Broadgoods
June 5, 2022 - SAE International

This document describes a manufacturing method for processing unidirectional carbon fiber/epoxy resin impregnated sheet and tape into multi-ply broadgoods and tape produced on an automated cross-plying machine. Broadgoods or tape of two or more ply configurations may be processed,...

GMW18033 - Exposed Weave Carbon Fiber Composite Parts Appearance Requirements
October 1, 2018 - GMW

Material Description. This standard describes the surface appearance and quality requirements for all exterior parts made of exposed weave carbon fiber composite parts in a vehicle including GM assembly plant painted parts, supplier painted parts, and exterior add-on parts. The...

Advertisement