1.1 This fire-test-response standard assesses the ability of non-mechanical fire dampers used in vented construction in its open state to limit passage of hot gases, radiation, and flames during a prescribed fire test exposure. The fire exposure condition in this test method is sudden direct...
1.1 This test method covers the laboratory testing of some of the acoustical properties of sound attenuating devices including duct liner materials, integral ducts, and in-duct absorptive straight and elbow silencers used in the ventilation systems of buildings. Procedures are described for the...
4.1 The objective of this near-miss recording and reporting guide is to support companies, organizations, workforce, and safety professionals in the collection, recording, reporting, analysis, and benchmarking of near-miss safety related events that can be leveraged for identifying and reducing...
1.1 This practice covers the identification requirements for installed firestop systems (FS), fire-resistive joint systems (FRJS), perimeter fire containment systems (PFCS), and continuity head-of-wall joint systems (CHWJS). These systems are installed on, in, or between fire resistance rated wall...
1.1 These test methods cover the testing of rubber intended for use in applications in which the rubber will be subjected to compressive stresses in air or liquid media. They are applicable particularly to the rubber used in machinery mountings, vibration dampers, and seals. Three test...
5.1 This guide is intended to describe various methods for determining the dynamic properties of vulcanized rubber materials, and by extension, products utilizing such materials in applications such as springs, dampers, and flexible load-carrying devices, flexible power transmission...
Note 1: Use of the standard designation ISO 6944 refers to both ISO 6944:1985 and ISO 6944-1:2008. 1.1 These test methods evaluate the fire-resistive metallic HVAC duct system's fire resistance and fire-engulfment with horizontal and vertical through-penetration firestops. Note 2: The intent of...
1.1 These requirements cover Type I commercial kitchen exhaust hoods intended for placement over commercial cooking equipment. Exhaust hoods with and without exhaust dampers are covered by these requirements. 1.2 Exhaust hoods with and without exhaust fire actuated fire dampers are...
1.1 Weigh-In-Motion-This
1.1 This Standard covers requirements as related to the following: a) Discrete electrical control units and accessories for fire alarm systems including smoke control, releasing, Building System Information Unit (BSIU), and emergency communication systems; b) Electrically- and...
1.1 This Standard sets forth requirements for smoke detectors and accessories, including mechanical guards to be employed in ordinary indoor locations in accordance with the following: a) In Canada only: 1) Standard for the Installation of Fire Alarm Systems, ULC-S524; 2) National Building Code of...
5.1 Air infiltration into the conditioned space of a building accounts for a significant portion of the thermal space condition load. Air infiltration can affect occupant comfort by producing drafts, cause indoor air quality problems by carrying outdoor pollutants into occupied building space and,...
5.1 Airtightness-Buildin
This specification establishes the general requirements for two types, two classes, and seven grades of rubber seals used in solar energy systems employing air-heat transport, such as duct and damper seals. Particular applications may necessitate other requirements that would take precedence...
This specification details the requirements of waterborne, sprayable sound damper (Liquid Applied Sound Damper (LASD)). The purpose of this material is to reduce vehicle metal noise vibrations excited by engine, tires, transmission and stone impingement. The material is applied in the...
This specification details the requirements of a waterborne, low bake, sprayable sound damper material with high acoustic performance. The material is applied in the paint shop after Electrocoat (E-Coat) bake, before primer surfacer. This material is intended to improve the acoustic sound...
This specification details the requirements of a waterborne, high bake, sprayable sound damper material with high acoustic performance. The material is applied in the paint shop after Electrocoat (E-Coat) bake, before primer surfacer. This material is intended to improve the acoustic sound...
1.1 These requirements cover heat responsive links used for fire-protection service. These links consist of devices intended for installation under load conditions such as for use with automatic fire suppression systems; or automatic closure devices for doors, windows, dampers or smoke...
1.1 These requirements cover heat responsive links used for fire-protection service. These links consist of devices intended for installation under load conditions such as for use with automatic fire suppression systems; or automatic closure devices for doors, windows, dampers or smoke...
Narrow Your Results