1.1 This specification covers the requirements for seamless copper tube (DWV) produced from copper UNS No. C12200 and intended for sanitary drainage, waste, and vent piping. Note 1: Fittings used for soldered or brazed connections in drainage, waste, or vent systems are described in...
1.1 This guide covers guidelines for the acceptance testing frequency requirements for geonet and geonet drainage geocomposite materials describing types of tests, test methods, and recommended verifications. 1.2 This guide is intended to aid purchasers, installers, contractors, owners,...
1.1 This test method is used to determine the potential for, and relative degree of, biological growth which can accumulate on geotextile, drainage geocomposites, or geotextile/soil filters. 1.2 This test method uses the measurement of flow rates over an extended period of time to determine...
This specification covers coextruded composite pipe, produced by a coextrusion die system, in which the concentric layers are formed and combined before exiting the die. Coextruded composite pipe conforming to the requirements prescribed are used for different applications: IPS Schedule 40...
4.1 The results obtained from this method can be used to determine the unit weight of compacted asphalt mixtures, and in conjunction with Test Method D3203, to obtain percent air voids. These values in turn may be used in determining the relative degree of compaction. 4.2 Since specific gravity has...
1.1 This test method covers procedures for determining the effect of freezing and thawing on exterior insulation and finish systems (EIFS), EIFS with drainage, or water-resistive barrier coating. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as...
1.1 This guide covers methods for determining and evaluating causes of water leakage of exterior walls. For this purpose, water penetration is considered leakage, and therefore problematic, if it exceeds the planned resistance or temporary retention and drainage capacity of the wall, is...
1.1 This practice covers a procedure for using life-cycle cost (LCC) analysis techniques to evaluate alternative drainage system designs using corrugated metal pipe that satisfies the same functional requirements. 1.2 The LCC technique measures the present value of all relevant costs of...
1.1 This specification covers the manufacture and purchase requirements of products used for the assembly and construction of circular vertical precast reinforced concrete manholes and structures used in sewer, drainage, and water works. 1.2 Part I, Sections 1 - 11, of this specification...
This specification covers requirements and test methods for materials, workmanship, dimensions, perforations, pipe stiffness, elongation, joint separation resistance, quality of extruded polyethylene, brittleness, bond, and marking of corrugated polyethylene (PE) pipe and fittings. This...
1.1 This specification covers cast iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. It establishes standards covering material, manufacture, mechanical and chemical properties, coating, test methods, inspection,...
1.1 This practice describes a procedure for field measurement of the infiltration rate of liquid (typically water) into soils using the modified Philip Dunne (MPD) infiltrometer. The data from the field measurement is then used to calculate the field hydraulic conductivity. Soils should be regarded...
This specification covers coextruded composite pipe, produced by a coextrusion die system, in which the concentric layers are formed and combined before exiting the die. Coextruded composite pipe conforming to the requirements prescribed are used for different applications: IPS Schedule 40...
5.1 In this test method, the compressive strength of a soil is determined in terms of the total stress, therefore, the resulting strength depends on the pressure developed in the pore fluid during loading. In this test method, fluid flow is not permitted from or into the soil specimen as the load...
1.1 These test methods cover laboratory measurement of the hydraulic conductivity (also referred to as coefficient of permeability) of water-saturated coarse-grained soils (for example, sands and gravels) with k > 10-7 m/s for various civil engineering applications including use as drain material...
5.1 The procedure described in this test method for determination of the shear resistance of the soil and geosynthetic or geosynthetic and geosynthetic interface is intended as a performance test to provide the user with a set of design values for the test conditions examined. The test specimens...
1.1 This specification covers PB Exterior Insulation and Finish Systems (EIFS) defined as an exterior, non-bearing wall covering providing a weather-resistant exterior wall envelope on walls required to be combustible or noncombustible, fire-resistance-rate
1.1 This specification covers requirements and test methods for annular, corrugated profile wall polyethylene pipe and fittings with an interior liner. The nominal inside diameters covered are 300?mm to 1500 mm [12?in. to 60 in.]. 1.2 The requirements of this specification are intended to provide...
This specification covers coextruded composite pipe, produced by a coextrusion die system, in which the concentric layers are formed and combined before exiting the die. Coextruded composite pipe conforming to the requirements prescribed are used for different applications: IPS Schedule 40...
This specification covers requirements, test methods, materials, and marking for polyethylene (PE), open bottom, buried arch-shaped chambers of corrugated wall construction used for collection, detention, and retention of stormwater runoff. These collection chambers can be used as commercial,...
Narrow Your Results