This specification covers cast gray iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. These pipe and fittings are not intended for pressure applications. The cast iron shall be produced by an established commercial method...
5.1 Field tests provide the most reliable relationship between the axial load applied to a deep foundation and the resulting axial movement. Test results may also provide information used to assess the distribution of side shear resistance along the element, the amount of end bearing developed at...
4.1 The bi-directional axial compressive load test provides separate, direct measurements of the axial capacity mobilized above an embedded jack assembly and element end bearing plus any axial capacity mobilized below the jack assembly. The maximum mobilized axial capacity equals two times the...
4.1 Cable-tool rigs (also referred to as churn rigs, water-well drilling rigs, spudders, or percussion rigs) are used in the oil fields and in the water-well industry. The Chinese developed the percussion method some 4,000 years ago. 4.2 Cable-tool drilling and sampling methods may be...
5.1 Field tests provide the most reliable relationship between the static lateral load applied to a deep foundation and the resulting lateral movement. Test results may also provide information used to assess the distribution of lateral resistance along the element and the long-term load-deflection...
This specification covers wire and rod in the alloys and the tempers suitable for manufacturing rivets and other similar items by cold-heading operations. The products covered by this specification shall be produced by extruding, rolling, or drawing, or a combination thereof, at the option of the...
5.1 Field tests provide the most reliable relationship between the axial load applied to a deep foundation and the resulting axial movement. Test results may also provide information used to assess the distribution of side shear resistance along the element and the long-term load-deflection...
4.1 Hollow-stem augers are frequently used for geotechnical exploration. One reason they are used is that the method is considered a "dry" drilling method where drill fluids are not needed to advance the borehole in unstable formations. Often, hollow-stem augers are used with other...
1.1 This test method covers collection and comparison of logs of thermalized-neutron counts and back-scattered gamma counts along horizontal or vertical air-filled access tubes. 1.2 Access tubes are installed either by drilling access holes or digging a trench into the media being measured....
4.1 Measurements of length change permit assessment of the potential for volumetric expansion or contraction of cast, drilled, or sawed specimens of hydraulic-cement mortar, and concrete due to various causes other than externally applied forces and temperature changes. This practice...
This specification covers cast gray iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. These pipe and fittings are not intended for pressure applications. The cast iron shall be produced by an established commercial method...
5.1 Temperature measurements taken from a thermal probe lowered into access ducts in the deep foundation element, or from embedded thermal sensors distributed along the length, or from embedded fiber optic cables can indicate the homogeneity and integrity of concrete both inside and outside...
5.1 The purpose of this practice is to outline a procedure for the detection and location of discontinuities such as pits, voids, inclusions, cracks, or abrupt dimensional variations in ferromagnetic tubing using the electromagnetic (eddy current) method. Furthermore, the relative severity of a...
5.1 Eddy-current testing is a nondestructive method of locating discontinuities in metallic materials. Signals can be produced by discontinuities originating on either the external or internal surfaces of the tube or by discontinuities totally contained within the wall. Since the density of eddy...
5.1 Soil-gas sampling results can be dependent on numerous factors both within and outside the control of the sampling personnel. Key variables are identified and briefly discussed below. Please see the documents listed in the Bibliography for more detailed information on the effect of various...
4.1 Cast-in-place cylinder strength relates to the strength of concrete in the structure due to the similarity of curing conditions because the cylinder is cured within the slab. However, due to differences in moisture condition, degree of consolidation, specimen size, and length-diameter...
6.1 This practice is used to determine the LR of specified glass types and constructions exposed to uniform lateral loads. 6.2 Use of this practice assumes: 6.2.1 The glass is free of edge damage and is properly glazed. 6.2.2 The glass has not been subjected to abuse. 6.2.3 The surface condition of...
1.1 This practice covers the determination of the thickness of glass installed in airport traffic control towers (ATCT) to resist a specified design loading with a selected probability of breakage less than or equal to either 1 lite per 1000 or 4 lites per 1000 at the first occurrence of the design...
1.1 This practice covers a procedure for preparing test specimens from magnesia-carbon and impregnated burned basic brick. This practice generally concerns preparation of test specimens from brick greater than 13 in. (33 cm) in length. These brick are mainly manufactured for use in electric...
This test method covers determination of the thickness of a concrete pavement, slab, or structural element by measuring the length of a core drilled from a concrete structure. The values stated in SI units are to be regarded as the standard. This standard does not purport to address...
Narrow Your Results