1.1 This specification covers the aesthetic quality requirements for decorative enamels applied to flat glass for use in building glazing. 1.2 This specification covers the requirements for flat glass, with either organic or ceramic enamels applied. 1.2.1 Glass may be annealed, heat-strengthened,..
1.1 This practice is intended for use with swept sine resonant ultrasound spectrometers capable of exciting, measuring, recording, and analyzing multiple whole body mechanical vibration resonant frequencies within parts exhibiting acoustical ringing in the acoustic or ultrasonic, or both, resonant...
This specification covers the dimensions and tolerances for both driving and driven elements in square drive interconnections on stainless steel surgical instruments used for drilling, tapping, driving, or placing of medical devices during surgery. The specification is intended to lessen the...
1.1 This guide covers how direct (straight) air-rotary drilling procedures may be used for geoenvironmental exploration and installation of subsurface water-quality monitoring devices. Note 1: The term direct with respect to the air-rotary drilling method of this guide indicates that...
5.1 The indirect tensile cracking test is used to determine asphalt mixture cracking resistance at an intermediate temperature which could range from 5?°C to 35?°C, depending on local climate. The specimens are readily obtained from Superpave gyratory compactor compacted cylinders with a diameter...
This specification covers cast gray iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. These pipe and fittings are not intended for pressure applications. The cast iron shall be produced by an established commercial method...
This specification covers the standard requirements for commercial zinc casting alloys in ingot form for use in the manufacture of sheet metal forming dies, sand cast or plaster cast forming dies, and plastic injection molds. Kirksite A alloy (UNS Z35543) is intended for use in the fabrication of...
1.1 This test method describes the use of the pocket penetrometer and allows for a simple and portable method to evaluate the consistency of cohesive soils. The pocket penetrometer is considered an index test and not an engineering test. 1.2 The test method can be used in the field or laboratory...
1.1 The test methods described in this standard measure axial displacements of a single, deep foundation element when loaded in bi-directional static axial compression using a non-retractable embedded jack assembly. These methods apply to all deep foundation elements, referred to herein as...
1.1 The test methods described in this standard measure the axial deflection of an individual vertical or inclined deep foundation element or group of elements when loaded in static axial compression. These methods apply to all types of deep foundations, or deep foundation systems as they are...
1.1 This test method covers determination of compressive strength of cylindrical concrete specimens such as molded cylinders and drilled cores. It is limited to concrete having a density in excess of 800 kg/m3?[50 lb/ft3]. 1.2 The values stated in either SI units or inch-pound units are to...
1.1 These test methods address compression (P) and shear (S) waves propagating in the downward direction in a nearly vertical plane. The seismic waves can be denoted as PV or PZ for a downward propagating compression wave and as SVH or SZX for downward propagating and horizontally polarized shear...
4.1 Environmental site characterization projects almost always require information regarding subsurface soil stratigraphy and hydraulic parameters related to groundwater flow rate and direction. Soil stratigraphy often is determined by various drilling procedures and interpreting the data...
This specification covers standard test method for tensile strength of concrete surfaces and the bond strength or tensile strength of concrete repair and overlay materials by direct tension (pull-off method). This test method is suitable for both field and laboratory use to determine one or more of...
This specification covers aluminum-alloy permanent mold castings. The responsibility of furnishing castings that can be laid out and machined to the finished dimensions within the permissible variations specified shall rest with the producer, except where mold equipment is furnished by the...
1.1 This guide describes the selection of materials, installation methods, and inspection required for sealing leaks at cracks in concrete building walls and slabs using chemical grout. The process discussed in this guide is a waterproofing repair in which voids in a concrete element are sealed...
5.1 Analysis of deflection data from asphalt pavements almost always requires that the raw deflections or the analysis results from the load-deflection data be adjusted for the effects of pavement surface course temperature. Measuring the temperature at depth normally requires that a hole be...
1.1 The test methods described in this standard measure the axial deflection of an individual vertical or inclined deep foundation element or group of elements when loaded in static axial tension. These methods apply to all types of deep foundations, or deep foundation systems, as they are...
1.1 The test methods described in this standard measure the lateral deflection of an individual vertical or inclined deep foundation element or group of elements when subjected to static lateral loading. These methods apply to all deep foundations, or deep foundation systems as they are practical...
This specification covers wire and rod in the alloys and the tempers suitable for manufacturing rivets and other similar items by cold-heading operations. The products covered by this specification shall be produced by extruding, rolling, or drawing, or a combination thereof, at the option of the...
Narrow Your Results