This Technical Report has been declared "CANCELLED" as of November 2017. By this action, this document will remain listed in the respective index, if applicable. Cancelled Technical Reports are available from SAE.
This specification establishes the requirements for four classes of machinable, high-density tungsten base metal produced by consolidating metal powder mixtures, the composition of which is mainly tungsten. This material specification may be used for bare parts or for parts that may be coated with...
This document specifies those requirements and procedures for periodic tests to insure maintenance of balance machine capabilities for balancing jet engine components. It will specify: (a) Requirements for tests (b) Calibration tests (c) Residual unbalance and accurate angle and...
This document specifies those requirements and procedures for periodic tests to insure maintenance of balance machine capabilities for balancing jet engine components. It will specify: (a) Requirements for tests (b) Calibration tests (c) Residual unbalance and accurate angle and...
1.1 The purpose of these practices is to specify procedures for the calibration of force-measuring instruments. Procedures are included for the following types of instruments: 1.1.1 Elastic force-measuring instruments, and 1.1.2 Force-multiplying systems, such as balances and small platform...
1.1 This test method covers the determination of slow crack growth (SCG) parameters of advanced ceramics by using constant stress rate rectangular beam flexural testing, ring-on-ring biaxial disk flexural testing, or direct tensile strength, in which strength is determined as a function of applied...
4.1 For many structural ceramic components in service, their use is often limited by lifetimes that are controlled by a process of slow crack growth. This test method provides the empirical parameters for appraising the relative slow crack growth susceptibility of ceramic materials under specified...
5.1 The seismic downhole method provides a designer with information pertinent to the seismic wave velocities of the materials in question (1). The P-wave and S-wave velocities are directly related to the important geotechnical elastic constants of Poisson's ratio, shear modulus, bulk modulus, and...
This ARP specifies both the nominal dimensions and the tolerances for a series of ball bearings with semifinished inside diameters which are suitable for supporting gas turbine rotating components in dynamic balancing machines.
1.1 This test method provides data for determining undrained strength properties and stress-strain relations for cohesive soils. This test method provides for the measurement of the total stresses applied to the specimen, that is, the stresses are not corrected for pore-water pressure. 1.2 This...
This ARP specifies both the nominal dimensions and the tolerances for a series of ball bearings with semifinished inside diameters which are suitable for supporting gas turbine rotating components in dynamic balancing machines.
5.1 Need for Heat Flux Measurements: 5.1.1 Independent measurements of temperature and heat flux support the development and validation of engineering models of fires and other high environments, such as furnaces. For tests of fire protection materials and structural assemblies, temperature and...
1.1 This standard covers two laboratory test methods for measuring the magnitude of one-dimensional wetting-induced swell or collapse of unsaturated soils and one method for measuring load-induced compression subsequent to wetting-induced deformation. 1.1.1 Method A is a procedure for measuring...
1.1 This test method covers collection and comparison of logs of thermalized-neutron counts and back-scattered gamma counts along horizontal or vertical air-filled access tubes. 1.2 Access tubes are installed either by drilling access holes or digging a trench into the media being measured. 1.3 The...
1.1 Soils consist of particles with various shapes and sizes. This test method is used to separate particles into size ranges and to determine quantitatively the mass of particles in each range. These data are combined to determine the particle-size distribution (gradation). This test method uses a...
1.1 These test methods cover the determination of the maximum dry unit weight of granular soils. A vibrating hammer is used to impart a surcharge and compactive effort to the soil specimen. Further, an optional calculation is presented to determine the approximate water content range for effective...
4.1 This practice provides organizations with a structured, systematic, and integrated approach to identifying, assessing, mitigating, monitoring, and reporting risks across all organizational functions. This practice is essential for ensuring that risk management contributes meaningfully to value...
Narrow Your Results