loading
GMW17844 - Tire and Wheel Assembly Dynamic Balancer Test
August 1, 2017 - GMW
A description is not available for this item.
ARP1340B - Periodic Surveillance Procedures for Horizontal Dynamic Balancing Machines
July 2, 2018 - SAE International

This Technical Report has been declared "CANCELLED" as of November 2017. By this action, this document will remain listed in the respective index, if applicable. Cancelled Technical Reports are available from SAE.

ASTM B777-15(2026) - Standard Specification for Tungsten Base, High-Density Metal
July 1, 2026 - ASTM International

This specification establishes the requirements for four classes of machinable, high-density tungsten base metal produced by consolidating metal powder mixtures, the composition of which is mainly tungsten. This material specification may be used for bare parts or for parts that may be coated with...

ARP1340A - Periodic Surveillance Procedures for Horizontal Dynamic Balancing Machines
December 17, 2012 - SAE International

This document specifies those requirements and procedures for periodic tests to insure maintenance of balance machine capabilities for balancing jet engine components. It will specify: (a) Requirements for tests (b) Calibration tests (c) Residual unbalance and accurate angle and...

MTW235 - Micro-Poise MTW-235 Dynamic Balancer Procedure Manual
August 1, 2010 - GMNA
A description is not available for this item.
ARP1340 - PERIODIC SURVEILLANCE PROCEDURES for HORIZONTAL DYNAMIC BALANCING MACHINES
December 16, 2002 - SAE International

This document specifies those requirements and procedures for periodic tests to insure maintenance of balance machine capabilities for balancing jet engine components. It will specify: (a) Requirements for tests (b) Calibration tests (c) Residual unbalance and accurate angle and...

ASTM E74-18(2026) - Standard Practices for Calibration and Verification for Force-Measuring Instruments
April 1, 2026 - ASTM International

1.1 The purpose of these practices is to specify procedures for the calibration of force-measuring instruments. Procedures are included for the following types of instruments: 1.1.1 Elastic force-measuring instruments, and 1.1.2 Force-multiplying systems, such as balances and small platform...

ASTM C1368-18(2026) - Standard Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress Rate Strength Testing at Ambient Temperature
June 1, 2026 - ASTM International

1.1 This test method covers the determination of slow crack growth (SCG) parameters of advanced ceramics by using constant stress rate rectangular beam flexural testing, ring-on-ring biaxial disk flexural testing, or direct tensile strength, in which strength is determined as a function of applied...

ASTM C1465-26 - Standard Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress-Rate Flexural Testing at Elevated Temperatures
June 1, 2026 - ASTM International

4.1 For many structural ceramic components in service, their use is often limited by lifetimes that are controlled by a process of slow crack growth. This test method provides the empirical parameters for appraising the relative slow crack growth susceptibility of ceramic materials under specified...

ASTM D7400/D7400M-26 - Standard Test Methods for Downhole Seismic Testing
February 15, 2026 - ASTM International

5.1 The seismic downhole method provides a designer with information pertinent to the seismic wave velocities of the materials in question (1). The P-wave and S-wave velocities are directly related to the important geotechnical elastic constants of Poisson's ratio, shear modulus, bulk modulus, and...

ARP1202 - BALL TYPE SLAVE BEARINGS FOR ROTOR SUPPORT IN DYNAMIC BALANCING MACHINES
July 1, 1973 - SAE International

This ARP specifies both the nominal dimensions and the tolerances for a series of ball bearings with semifinished inside diameters which are suitable for supporting gas turbine rotating components in dynamic balancing machines.

ASTM D2850-26 - Standard Test Method for Unconsolidated-Undrained Triaxial Compression Test on Cohesive Soils
January 1, 2026 - ASTM International

1.1 This test method provides data for determining undrained strength properties and stress-strain relations for cohesive soils. This test method provides for the measurement of the total stresses applied to the specimen, that is, the stresses are not corrected for pore-water pressure. 1.2 This...

ARP1202B - Balancing Machines, Dynamic, Ball Type Slave Bearings for Rotor Support
April 25, 2019 - SAE International

This ARP specifies both the nominal dimensions and the tolerances for a series of ball bearings with semifinished inside diameters which are suitable for supporting gas turbine rotating components in dynamic balancing machines.

ASTM E3057-26 - Standard Test Method for Measuring Heat Flux Using Directional Flame Thermometers with Advanced Data Analysis Techniques
January 1, 2026 - ASTM International

5.1 Need for Heat Flux Measurements: 5.1.1 Independent measurements of temperature and heat flux support the development and validation of engineering models of fires and other high environments, such as furnaces. For tests of fire protection materials and structural assemblies, temperature and...

ASTM D4546-25 - Standard Test Methods for One-Dimensional Swell or Collapse of Soils
December 1, 2025 - ASTM International

1.1 This standard covers two laboratory test methods for measuring the magnitude of one-dimensional wetting-induced swell or collapse of unsaturated soils and one method for measuring load-induced compression subsequent to wetting-induced deformation. 1.1.1 Method A is a procedure for measuring...

ASTM D6031/D6031M-25 - Standard Test Method for Nuclear Gauge Logging In Situ Water Content and Density of Soil and Rock in Drilled Access Holes or Trenches Using Horizontal, Slanted, and Vertical Access Tubes
October 15, 2025 - ASTM International

1.1 This test method covers collection and comparison of logs of thermalized-neutron counts and back-scattered gamma counts along horizontal or vertical air-filled access tubes. 1.2 Access tubes are installed either by drilling access holes or digging a trench into the media being measured. 1.3 The...

ASTM D6913/D6913M-17(2025) - Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis
October 1, 2025 - ASTM International

1.1 Soils consist of particles with various shapes and sizes. This test method is used to separate particles into size ranges and to determine quantitatively the mass of particles in each range. These data are combined to determine the particle-size distribution (gradation). This test method uses a...

ASTM D7382-25 - Standard Test Methods for Determination of Maximum Dry Unit Weight of Granular Soils Using a Vibrating Hammer
October 15, 2025 - ASTM International

1.1 These test methods cover the determination of the maximum dry unit weight of granular soils. A vibrating hammer is used to impart a surcharge and compactive effort to the soil specimen. Further, an optional calculation is presented to determine the approximate water content range for effective...

ASTM E3502-25 - Standard Practice for Enterprise Risk Management (ERM)
September 15, 2025 - ASTM International

4.1 This practice provides organizations with a structured, systematic, and integrated approach to identifying, assessing, mitigating, monitoring, and reporting risks across all organizational functions. This practice is essential for ensuring that risk management contributes meaningfully to value...

Advertisement