loading
FORD M5J29-A - SANDLEWOOD ENAMEL
October 1, 1990 - FORD

1. SCOPE: The material desired under this Standard is a durable high gloss alkyd resin air dry enamel.

AMS3122G - Enamel, Phenolic Black Baking
July 22, 2013 - SAE International

This specification covers a semigloss black baking enamel based on a phenolic resin.

AMS3122E - Enamel, Phenolic Black Baking
February 25, 2004 - SAE International

This specification covers a semigloss black baking enamel based on a phenolic resin.

AMS3122D - ENAMEL, PHENOLIC Black Baking
February 1, 1998 - SAE International

This specification covers a semigloss black baking enamel based on a phenolic resin.

AMS3122C - ENAMEL, PHENOLIC Black Baking
January 1, 1977 - SAE International

This specification covers a semigloss black baking enamel based on a phenolic resin.

A-A-2787 - Enamel, Aerosol (Low VOC)
November 27, 2009 - NPFC

This description covers two types of aerosol enamels meeting National Volatile Organic Compound Emission Standards for Aerosol coatings, 40 CFR 59, Subpart E. The aerosol enamel shall be furnished in nominal 475 mL (1-pint) commercial pressurized dispensers with cover caps protecting...

FORD SK-M32J9552-B - ENAMEL, ACRYLIC BAKING, EXTERIOR
December 19, 1994 - FORD

1. SCOPE The material defined by this specification is a thermosetting acrylic enamel.

FORD SK-M32J9552-C - ENAMEL, ACRYLIC BAKING, EXTERIOR
December 19, 1994 - FORD

1. SCOPE The material defined by this specification is a thermosetting acrylic enamel.

FORD SK-M32J9552-A - ENAMEL, ACRYLIC BAKING, EXTERIOR
December 19, 1994 - FORD

1. SCOPE The material defined by this specification is a thermosetting acrylic enamel.

FORD M5J92-A - DELTA PHOSPHORESCENT ORANGE ENAMEL
October 1, 1990 - FORD

1. SCOPE: The material desired under this standard is a durable phosphorescent air dry enamel.

GMSA EMS.TI.0215 - Synthetic enamel air drying
June 1, 2011 - GMSA

I. - SCOPE This spec. covers requirements for a synthetic air drying enamel, surtable for optional use on assembled bodies repainting.

FORD ESA-M64J17-A - ENAMEL, WATERBORNE ELECTROCOAT - ACRYLIC
January 10, 1979 - FORD

1. SCOPE The material defined by this specification is a heat curing electrocoating enamel.

FORD M5J23-A - PEACH FLAT ENAMEL
October 1, 1990 - FORD

1. SCOPE: The material desired under this Standard is a durable high gloss alkyd resin air dry enamel.

FORD M5J11-A - FLAT BLACK MAINTENANCE ENAMEL
October 1, 1990 - FORD

1. SCOPE: The material defined by this Standard is a high quality flat alkyd resin air dry enamel.

FORD M14J504-A - THINNER - EXEMPT ENAMEL
October 1, 1990 - FORD

1. SCOPE: This standard establishes the chemical, physical and functional properties of a blended thinner for synthetic enamels exempt from normal air pollution control requirements.

GMSA EMS 9310021 - Engine black enamel
June 1, 2011 - GMSA

1 Scope This specification covers requirements for an oven drying (epoxy, polyester) solvent borne enamel suitable to be applied over cast iron parts (eg. Engine blocks painting). Note: Material must be exempted of lead; chlorinated solvents and benzol.

GMSA EMS 9309727 - Synthetic surfacer for enamel
June 1, 2011 - GMSA

1. SCOPE: This specification covers the requirements for a themsetting, sandable, solvent borne synthetic surfacer that is applied by spraying and/or electrostactly, and topcoated with enamels. Specified herein are the painted product, process, labratory perfomce, and paint...

FORD SK-M21J9550-A - ENAMEL, SYNTHETIC BAKING, EXTERIOR
December 19, 1994 - FORD

1. SCOPE The material defined by this specification is a synthetic baking enamel, exterior quality, for wet on wet application over SK-M6J9556-A primer or equivalent. The material must be suitable for pneumatic as well as for electrostatic application.

GMW16711 - Emblem – Vitreous Enamel (Cloisonné)
July 1, 2017 - GMW

Material Description. These emblems are constructed of a Vitreous Enamel (Cloisonné) applied to a Gilders Bronze, Unified Numbering System (UNS) C21000 quarter hard per SAE J463, with chrome plate. Symbols. Not applicable. Applicability. This specification covers the performance requirements...

GMSA EMS.TI.0213 - Catalised Polyurethanic Enamel
April 1, 2002 - GMSA

1 Scope This specification defines requirements for a catalysed polyurethanic enamel solvent borne, suitable to be applied over primed plastic substrates, or on bodies and components paint repairs. 1 Descrição Esta especificação define os requisitos de um esmalte poliuretânico...

Advertisement