loading
ASTM E1570-19(2026) - Standard Practice for Fan Beam Computed Tomographic (CT) Examination
May 1, 2026 - ASTM International

5.1 This practice establishes the basic parameters for the application and control of fan-beam CT examinations. This practice is written so it can be specified on the engineering drawing, specification, or contract. It will require a detailed procedure delineating the technique or procedure...

ASTM E477-26 - Standard Test Method for Laboratory Measurements of Acoustical and Airflow Performance of Duct Liner Materials and Prefabricated Silencers
February 1, 2026 - ASTM International

5.1 Specimens tested using this standard, for example, duct silencers, are used to control sound propagation through ventilation ducts. The results gathered from testing specimens to this standard can be used to estimate the reduction in fan sound levels in ducted airflow systems caused by...

ASTM E641-25 - Standard Methods for Testing Hydraulic Spray Nozzles Used in Agriculture
October 1, 2025 - ASTM International

1.1 These methods cover procedures for testing hydraulic spray nozzles used in agriculture. The methods herein cover the following performance parameters: nozzle flow rate, nozzle spray angle, liquid distribution, spray droplet size, and nozzle wearability. 1.2 These methods are applicable to...

ASTM F2519-05(2025) - Standard Test Method for Grease Particle Capture Efficiency of Commercial Kitchen Filters and Extractors
August 1, 2025 - ASTM International

5.1 The pressure drop results can be added to the pressure drops of other components in an exhaust system to determine the total exhaust fan pressure requirement. 5.2 The particulate capture efficiency can be used with known particulate size emission data for a cooking appliance-food product...

ASTM E3474-25 - Standard Test Method for Measuring the Air Leakage Rate of the Building Envelope of an Individual Test Zone within a Multizone Building
August 1, 2025 - ASTM International

1.1 This test method provides a quantitative ?eld test procedure and calculation method for assessing an air leakage rate using fan-induced pressure differentials across the test envelope and the surrounding building, generated by multiple blower doors or equivalent equipment. 1.2 Building...

ASTM E1814-25 - Standard Practice for Computed Tomographic (CT) Examination of Castings
June 1, 2025 - ASTM International

1.1 This practice covers a uniform procedure for the examination of castings by the computed tomography (CT) technique including both cone and fan beam. The requirements expressed in this practice are intended to control the quality of the nondestructive examination by CT and are not...

ASTM D3161/D3161M-20(2025) - Standard Test Method for Wind Resistance of Steep Slope Roofing Products (Fan-Induced Method)
January 1, 2025 - ASTM International

1.1 This test method covers the procedure for evaluating the wind resistance of many discontinuous, air permeable, steep slope roofing products that results from the product's rigidity, with or without contribution from sealant to help hold down the leading edge of the tabs, or mechanical...

ASTM E1998-25 - Standard Guide for Assessing Depressurization-Induced Backdrafting and Spillage from Vented Combustion Appliances
February 1, 2025 - ASTM International

1.1 This guide describes and compares different methods for assessing the potential for, or existence of, depressurization-induced backdrafting and spillage from vented residential combustion appliances. 1.2 Assessment of depressurization-induced backdrafting and spillage is conducted under either...

ASTM F3734-24 - Standard Test Method for Performance of Commercial Range Ovens
November 1, 2024 - ASTM International

1.1 This test method covers the energy consumption and cooking performance evaluation of range ovens. The results of applying it can be used by the food service operator to select a range oven and to understand its energy consumption and performance. 1.2 This test method applies to general purpose,...

ASTM E2459-24 - Standard Guide for Measurement of In-Duct Sound Pressure Levels from Large Industrial Gas Turbines and Fans
October 1, 2024 - ASTM International

5.1 All noise control features associated with the inlet or exhaust of large industrial fans and gas turbines are, or should be, based upon inlet or exhaust sound power levels in octave bands of frequency. Sound power levels are not directly measurable, however, so they must be calculated...

ASTM F3338-24 - Standard Specification for Design of Electric Engines for General Aviation Aircraft
September 15, 2024 - ASTM International

1.1 This specification covers minimum requirements for the design of electric engines. 1.2 Distributed propulsion is not excluded; however, additional requirements will be needed to address the additional issues that distributed propulsion can create. Some of those issues may include: use of a...

ASTM D8101/D8101M-24 - Standard Test Method for Measuring the Penetration Resistance of Composite Materials to Impact by a Blunt Projectile
November 1, 2024 - ASTM International

1.1 This test method measures the resistance of flat composite panels in one specific clamping configuration to penetration by a blunt projectile in free flight. In this test method, the term "penetration" is defined as the case in which the projectile travels completely through the composite panel...

ASTM E741-24 - Standard Test Method for Determining Air Change in a Single Zone by Means of a Tracer Gas Dilution
July 1, 2024 - ASTM International

5.1 Effects of Air Change-Air change often accounts for a significant portion of the heating or air-conditioning load of a building. It also affects the moisture and contaminant balances in the building. Moisture-laden air passing through the building envelope can permit condensation and cause...

ASTM E3158-24 - Standard Test Method for Measuring the Air Leakage Rate of a Large or Multizone Building
July 1, 2024 - ASTM International

1.1 This standard test method covers a quantitative field-test procedure and calculation method for assessing an air leakage rate using a fan-induced pressure differential(s) across the building envelope, generated by blower doors or equivalent equipment. 1.2 Building setup conditions in...

ASTM F2361-18(2024) - Standard Guide for Ordering Low Voltage (1000 VAC or Less) Alternating Current Electric Motors for Shipboard Service—Up to and Including Motors of 500 Horsepower
May 1, 2024 - ASTM International

This guide provides the required basic ordering information for low voltage (1000 VAC or less, and up to and including motors of 500 hp) general-purpose (GP), commercial, universal, small and medium sized alternating current electric motors intended to drive common shipboard mechanical machinery...

ASTM E1258-23 - Standard Test Method for Airflow Calibration of Fan Pressurization Devices
July 1, 2023 - ASTM International

5.1 The fan pressurization procedure provides a relatively fast evaluation of the airtightness of building envelopes. In order for the accuracy of the test results to be known, the airflow rate measurement technique of the fan pressurization system must be calibrated. 5.2 This test...

ASTM F1075-97(2023) - Standard Specification for Dehumidifier, Shipboard, Mechanically Refrigerated, Self-Contained
December 1, 2023 - ASTM International

This specification covers the performance requirements and corresponding test procedures for self-contained shipboard dehumidifiers that use hermetic refrigerant motor-compressors. The components of the dehumidifier, including the motor-compressor, condensing unit, dehumidifying coil,...

ASTM F2976-13(2023) - Standard Practice for Determining the Field Performance of Commercial Kitchen Demand Control Ventilation Systems
August 1, 2023 - ASTM International

5.1 Fan Energy-This standard practice determines the fan energy requirements for a constant speed and demand controlled kitchen ventilation system and estimates the savings. It can be used to compare systems' fan savings potential. 5.2 Heating and Cooling Energy-This standard...

ASTM E1554/E1554M-13(2023) - Standard Test Methods for Determining Air Leakage of Air Distribution Systems by Fan Pressurization
October 1, 2023 - ASTM International

5.1 Air leakage between an air distribution system and unconditioned spaces affects the energy losses from the distribution system, the ventilation rate of the building, and the entry rate of air pollutants. 5.2 The determination of infiltration energy loads and ventilation rates of residences and...

Advertisement