1.1 This test method covers the determination of the annealing point and the strain point of a glass by measuring the viscous elongation rate of a fiber of the glass under prescribed condition. 1.2 The annealing and strain points shall be obtained by following the specified procedure after...
1.1 This specification covers machine-made fiberglass pipe intended for use in gravity-flow systems for conveying sanitary sewage, storm water, and some industrial wastes. Both glass-fiber-reinforced thermosetting-resin pipe (RTRP) and glass-fiber-reinforced polymer mortar pipe (RPMP)...
5.1 This is intended to outline O&M issues that require discussion and mutual agreement by both the optical fiber cable owner and sewer pipeline operator. The purpose is developing sufficient written procedures and practices to allow optical fiber systems to coexist as a secondary use...
1.1 This specification covers either untextured or surface textured fiber-cement flat sheets intended for exterior applications such as wall claddings, facades, curtain walls, soffits, trim, and so forth. 1.2 This specification is not applicable to asbestos-cement flat sheets (Specification...
1.1 This test method covers the determination of transthickness tensile strength under monotonic uniaxial tensile loading of continuous fiber-reinforced ceramics (CFCC) at ambient temperature. This test method addresses, but is not restricted to, various suggested test specimen geometries,...
5.1 Continuous fiber-reinforced ceramic composites are candidate materials for structural applications requiring high degrees of wear, erosion, corrosion resistance, and damage tolerance at high temperatures. 5.2 The 1D and 2D CFCCs are highly anisotropic and their transthickness tensile and...
5.1 Glass-fiber roving chopping rates, determined by this test method, are useful for quality control of GFRC products to ensure that manufacturing equipment has been set up to deliver the correct proportions of concrete and glass fiber reinforcement for producing a GFRC composite....
5.1 Slurry Flow Rates, determined by this test method, are useful for quality control of GFRC products to ensure that manufacturing equipment has been set up to deliver the correct proportions of concrete and glass fiber reinforcement for producing a GFRC composite. This test method is...
1.1 This specification establishes minimum characteristics for those factors that determine particle size, consistency, purity, and ability to drain. 1.2 Engineered wood fiber that meets the requirements of this specification must comply with Specification F1292, if the surface is in the use...
5.1 Cotton fiber that is on average finer and more mature is more desirable than coarse or immature fiber, although distinction between these qualities cannot be made quickly and accurately using current test methods. Immature fibers break more easily during processing and have...
4.1 This practice details a fiber training program that identifies the information and guidelines necessary for preparing a trainee to become a qualified FSP. The trainee is under the direct supervision of a qualified FSP throughout their training. Upon successful completion of the program,...
1.1 This standard is the compilation of all terminology developed by Subcommittee D13.11 on Cotton Fibers. 1.2 This terminology is unique to the Cotton Fibers industry. Meanings of the same terms used outside the industry can be found in other compilations or in dictionaries of...
1.1 This guide addresses only primary safety concerns, easements, constructability, liability of the various parties, and risk management related to constructing, installing, maintaining, or changing an optical fiber network in an existing sewer. 1.2 The text of this standard references...
1.1 This practice covers acoustic emission (AE) examination or monitoring of panel and plate-like composite structures made entirely of fiber/polymer composites. 1.2 The AE examination detects emission sources and locates the region(s) within the composite structure where the emission...
5.1 Properties determined by this test method are useful in the evaluation of new fibers at the research and development levels. Fibers with diameters up to 250 × 10-6 m are covered by this test method. Very short fibers (including whiskers) call for specialized test techniques...
4.1 The presence of 4-CBA and p-TOL in PTA used for the production of polyester is undesirable because they can affect the PET quality (such as contribute to fiber breaks), the polymerization process, and 4-CBA imparts coloration to the polymer due to thermal instability. 4.2 Determining the...
1.1 This practice provides recommended procedures for sampling synthetic turf fiber and finished fabric in a manufacturing location for further testing to identify and quantify per- and polyfluoroalkyl substances (collectively hereafter referred to as PFAS) in synthetic turf fiber and...
1.1 This standard is a compilation of terminology developed by Committee D13.18 on Glass Fiber and its Products. 1.2 This terminology is unique to glass fibers, strands, yarns, fabrics, etc. in the glass textile industry. Terms that are generally understood or adequately defined in...
Narrow Your Results