1.1 This test method covers the procedure for a finite flash point test, within the range of -25?°C to 90?°C, of liquid wastes using an MCCCFP tester. This test method is used in the determination of flash point of liquid wastes. Note 1: The connection of tap water or a cooling device...
1.1 This practice covers procedures to evaluate the compatibility of coatings with additives used to prevent flash rusting of steel before application of coatings. 1.2 The additives are used with vapor blast, wet abrasive blast (WAB), low or high pressure water cleaning (LPWC, HPWC), and...
This specification covers seven grades of diesel fuel oils suitable for various types of diesel engines. These grades are: Grade No. 1-D S15; Grade No. 1-D S500; Grade No. 1-D S5000; Grade No. 2-D S15; Grade No. 2-D S500; Grade No. 2-D S5000; and Grade No. 4-D. The requirements specified for diesel...
1.1 These practices describe laboratory procedures for preparing an oil-based ink resin solution in a high-boiling solvent using four pieces of lab equipment: (1) A hot oil bath (Sections 4 to 11), (2) A stirrer/hot plate (Sections 12 to 16), (3) An industrial blender (Sections 17 to 22), and (4) A...
5.1 The loss of volatile materials from greases and oils can adversely affect the original performance characteristics of a lubricant and, therefore, could be a significant factor in evaluating a lubricant for a specific use. Such volatiles can also be considered contaminants in the environment in...
1.1 The visual surface preparation guides and standards consist of a series of color prints available as separate publications. Five different sets of photographs are described in this practice, designated as Method A (ISO/Swedish Standard) and Methods B through E (SSPC Guides and Reference...
This specification covers the properties, sampling, and testing of asphalt suitable for undersealing Portland cement concrete and overlaid concrete pavements by pumping hot asphalt under the slabs. The asphalt shall be homogeneous and free of water and shall conform to the following requirements...
This specification covers a high fire point natural vegetable oil ester insulating fluid for use as a dielectric and cooling medium in new and existing power and distribution electrical apparatus such as transformers and attendant equipment. The physical property requirement including color, fire...
1.1 This guide presents background and guidelines for establishing an appropriate sequence of tests and data analysis procedures for determining the ionizing radiation (total dose) hardness of microelectronic devices for dose rates below 300 rad(SiO2)/s. These tests and analysis will be appropriate...
1.1 This practice is intended to provide accepted installation procedures for thin brick units in adhered veneer systems in residential and commercial construction. This information is meant to complement the specific installation instructions provided by manufacturers of clay and shale thin brick...
1.1 These test methods cover the determination of the flash point of petroleum products in the temperature range from 40?°C to 370?°C by a manual Pensky-Martens closed-cup apparatus or an automated Pensky-Martens closed-cup apparatus, and the determination of the flash point of...
This test method covers the determination of non-volatile matter, that is, residue on evaporation, in solvent extract from aerospace components, using a rotary flash evaporator. The summary of the test method, the apparatus for testing, reagents and materials for testing, and procedure for...
This specification covers cylindrical corrosion-resistant tanks made of commercial-grade glass-fiber-reinforc
This specification covers seven grades of diesel fuel oils suitable for various types of diesel engines. These grades are: Grade No. 1-D S15; Grade No. 1-D S500; Grade No. 1-D S5000; Grade No. 2-D S15; Grade No. 2-D S500; Grade No. 2-D S5000; and Grade No. 4-D. The requirements specified for diesel...
This specification covers grades of fuel oil intended for use in various types of fuel-oil-burning equipment under various climatic and operating conditions. These grades include the following: Grades No. 1 S5000, No. 1 S500, No. 2 S5000, and No. 2 S500 for use in domestic and small industrial...
This guide covers the selection and use of procedures for testing solvent-borne architectural coatings to be used on exterior, interior, or both types of surfaces. The properties that can be examined by the test methods listed herein are as follows: liquid paint properties (skinning, condition in...
This specification covers grades of fuel oil intended for use in various types of fuel-oil-burning equipment under various climatic and operating conditions. These grades include the following: Grades No. 1 S5000, No. 1 S500, No. 2 S5000, and No. 2 S500 for use in domestic and small industrial...
This specification covers two grades of burner fuel consisting of triglycerides and naturally occurring constituents of triglycerides including monoglycerides, diglycerides, and free fatty acids and distinguished by the pour point. The triglyceride burner fuels, Grade TBF5 and Grade TBF6, are...
This specification covers nominal wall cylindrical steel pipe piles in which the steel cylinder acts as a permanent load-carrying member or as a shell to form cast-in-place concrete piles. Each welded pile shall be made by seamless, electric resistance welding, flash welding or fusion...
4.1 When choosing a thermal insulation product or combination of products, physical, chemical and mechanical properties and the significance of those properties should be considered. ASTM test methods are usually performed under laboratory conditions and may not accurately represent field...
Narrow Your Results