loading
SEMI MATERIALS - MATERIALS
SEMI
A description is not available for this item.
J3281_202305 - Desorption of Brake Friction Materials
May 10, 2023 - SAE International

This SAE Recommended Practice specifies a method to reduce and stabilize the moisture of products containing brake friction material (disc brake pads, drum brake shoes, friction blocks) so the parts are conditioned and maintained in a stable low moisture state.

J2725_202304 - Road Vehicles - Friction Materials - Elastic Properties Measurements
April 21, 2023 - SAE International

This SAE Standard specifies a method for testing and measuring elastic constants in friction materials by precise ultrasonic velocity measurements. Measurement methods are also described for measurement of the out-of-plane modulus as a function of pre-load as well as the measurement...

J2968/1_202209 - Measurement of Material Properties for Wet Friction Materials
September 30, 2022 - SAE International

This SAE Recommended Practice is intended as the definition of a standard test, which may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering its use. The specific purpose of this SAE Recommended Practice is to define a...

J3231_202206 - Deflection Measurement for Friction Materials Using Segment Applicator
June 13, 2022 - SAE International

This SAE Recommend Practice specifies a method for measuring the deflection of friction materials and disc brake pad assemblies in a manner more consistent with classical material compressive strain testing. This SAE test method differs from SAE J2468 in the preload and maximum...

J3079/1_202101 - Validation of Compressibility Test Systems for Friction Materials
January 13, 2021 - SAE International

This SAE Recommended Practice (RP) applies to the validation process for test systems used to measure deflection (compressibility, creep, or swell and growth) of friction materials and friction material assemblies. The materials or assemblies can fit passenger...

J380_201702 - Specific Gravity of Friction Material
February 2, 2017 - SAE International

Specific gravity is a nondestructive test used as a quality control check of the consistency of formulation and processing of brake lining. The specific gravity and the range of specific gravity are peculiar to each formulation and, therefore, the acceptable values or range must be established for...

J2975_202007 - Measurement of Copper and Other Elements in Brake Friction Materials
July 23, 2020 - SAE International

This procedure describes a method for generating, preparing and analyzing samples of new and unused brake friction materials for their chemical constituents.

GMW18060 - Torque Converter Clutch Friction Material Performance Converter on Electric Dynamometer
October 1, 2018 - GMW

Purpose. This procedure was developed to evaluate the performance of the bonded friction material on a Torque Converter Clutch (TCC) under standard conditions of temperature and pressure. This assessment describes procedures for Torque Converter (TC) only testing. The TC is directly...

J3013_201911 - Friction Material Elastic Constants Determination through FRF Measurements and Optimization
November 20, 2019 - SAE International

This SAE Standard specifies necessary procedures and control parameters in estimating anisotropic elastic constants of friction material based on pad assembly FRF measurements and optimization. It is intended to provide a set of elastic constants as inputs to brake NVH simulation,...

J3175_201911 - Road Vehicles - Friction Materials - Finished Brake Pad Normalized Elastic Constant of Friction Material
November 20, 2019 - SAE International

This SAE standard specifies a method for testing and measuring a normalized elastic constant of brake pad assemblies using ultrasound. This document applies to disc brake pad assemblies and its coupons or segments used in road vehicles.

J2707_202106 - Wear Test Procedure on Inertia Dynamometer for Brake Friction Materials
June 10, 2021 - SAE International

This SAE Recommended Practice (RP) specifies a dynamometer test procedure to characterize wear rates of automotive service brake linings (brake shoes) and disc brake pads.

J2468_201811 - High-Preload Deflection and Compressibility Test Procedures for Friction Materials
November 12, 2018 - SAE International

This standard specifies a method for testing and measuring the deflection of friction materials assemblies and compressibility of friction materials. This standard applies to disc brake pad assemblies and its coupons or segments, brake shoe lining and its coupons or...

J2724_201605 - Measurement of Disc Brake Friction Material Underlayer Distribution
May 24, 2016 - SAE International

This procedure describes a method for measuring the fraction of underlayer (also referred to as backing layer) existing at any given height above the a disc brake friction materials shoe plate. Measuring underlayer distribution is useful for computing useable lining thickness and for...

FORD SQ-M11P9000-AA - BONDING FRICTION MATERIAL TO METAL
December 19, 1994 - FORD

1. SCOPE This specification covers the requirements and processes for bonding friction material to metal for operating in oil.

ASTM D6932/D6932M-26 - Standard Guide for Materials and Construction of Open-Graded Friction Course Plant Asphalt Mixtures
May 1, 2026 - ASTM International

4.1 This guide provides information to assist engineers with the design requirements and construction guidelines for paving an open-graded friction course (OGFC) surface layer. An OGFC is primarily used to improve the skid resistance and wear resistance of an asphalt pavement by providing an...

ASTM D3702-24 - Standard Test Method for Wear Rate and Coefficient of Friction of Materials in Self-Lubricated Rubbing Contact Using a Thrust Washer Testing Machine
November 1, 2024 - ASTM International

5.1 This test method is used to determine the equilibrium rate of wear and coefficient of friction of materials in rubbing contact under useful operating conditions, that is, combinations of pressure and velocity that fall below the PV (pressure?×?velocity) limit of the test...

ASTM G203-10(2026) - Standard Guide for Determining Friction Energy Dissipation in Reciprocating Tribosystems
June 1, 2026 - ASTM International

5.1 Many sliding systems exhibit intermittent high friction force excursions compared to competing tribosystems. However, where friction forces or friction coefficients are averaged, the test data may show that the two systems have the same friction characteristics, when...

Advertisement