1.1 This specification covers unalloyed and alloyed tantalum rod and wire. 1.2 The materials covered by this specification are: 1.2.1 R05200, unalloyed tantalum, electron-beam furnace or vacuum-arc melt, or both, 1.2.2 R05400, unalloyed tantalum, powder-metallurgy consolidation, 1.2.3...
This specification covers a group of common requirements that, unless covered by the individual product specification in another ASTM document, applies to steel forgings for general use. Materials shall be produced primarily by either electric-furnace, basic oxygen, vacuum-induction (VIM),...
1.1 This test method applies to the determination of hydrogen in nuclear-grade uranium oxide powders and pellets to determine compliance with specifications. Gadolinium oxide (Gd2O3) and gadolinium oxide-uranium oxide powders and pellets may also be analyzed using this test method. 1.2 This...
This specification covers a group of common requirements that, unless covered by the individual product specification in another ASTM document, applies to steel forgings for general use. Materials shall be produced primarily by either electric-furnace, basic oxygen, vacuum-induction (VIM),...
This specification covers hot-, cold-, or both hot- and cold-rolled hafnium rods and wires in either one of two grades. All grades should be in the recrystallization annealed condition unless specified otherwise. The materials should be made from ingots produced by vacuum melting in an electron...
5.1 The analysis of many types of water for metals using flame atomic absorption spectrophotometry, inductively coupled plasma emission spectrophotometry, direct current plasma emission spectrophotometry, or graphite furnace atomic absorption spectrophotometry necessitates the use of a...
5.1 Barium ranks about sixth in order of abundance in nature; however, it is normally found in only trace quantities in drinking water. Consumption, inhalation, or absorption of 500?mg to 600?mg is considered fatal to human beings. Lower levels may result in disorders of the heart, blood vessels,...
1.1 This test method covers the determination of copper in jet fuels in the range of 5?μg/kg to 100?μg/kg using graphite furnace atomic absorption spectrometry. Copper contents above 100?μg/kg may be determined by sample dilution with kerosine to bring the copper level into the...
This specification covers wrought carbon steel and alloy steel pipe fittings of seamless and welded construction for use in pressure piping and pressure vessel service at low temperatures. Materials shall consist of forgings, bars, plates, seamless or fusion welded tubular products with filler...
5.1 This test method is a comparative method intended primarily to test materials for compliance with compositional specifications or for monitoring. It is assumed that all who use these procedures will be trained analysts capable of performing common laboratory procedures skillfully and safely. It...
This specification covers aggregates used for masonry grout. Aggregates should consist of either natural or manufactured sand, used alone or in combination with course aggregates. The course aggregates should be made up of crushed stone, gravel, or processed air-cooled iron blast-furnace...
This specification covers aggregate for use in masonry mortar. Aggregate for use in masonry mortar shall consist of natural sand or manufactured sand. Manufactured sand is the product obtained by crushing stone, gravel, or air-cooled iron blast-furnace slag specially processed to ensure...
1.1 This test method covers the determination of the dynamic elastic properties of advanced ceramics. Specimens of these materials possess specific mechanical resonant frequencies that are determined by the elastic modulus, mass, and geometry of the test specimen. Therefore, the dynamic elastic...
1.1 This practice covers the optimization of graphite furnace atomic absorption spectrometers and the checking of spectrometer performance criteria. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns,...
1.1 This practice covers the optimization of graphite furnace atomic absorption spectrometers and evaluation of spectrometer performance criteria. 1.2 The values stated in SI units are regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any,...
1.1 This test method covers the determination of sulfur in samples of coal or coke by high-temperature tube furnace combustion. 1.1.1 Two analysis methods are described. 1.2 When automated equipment is used, either method can be classified as an instrumental method. 1.3 The values stated in...
This specification covers bare round copper-clad steel wire for electronic application. Four classes of copper-clad steel wire are covered as Class 30HS, 30A, 40HS, and 40A. The wire shall consist of a core of homogeneous open-hearth, electric-furnace, or basic-oxygen steel with a continuous...
1.1 This practice covers drying, homogenization, and ammonium bifluoride-nitric acid digestion of soil samples and associated quality control (QC) samples for the determination of metals and metalloids using laboratory atomic spectrometry analysis techniques such as inductively coupled plasma mass...
5.1 Results obtained from the test method are used to serve a number of interests, including the indication of possible boiler tube fouling and possible furnace corrosion problems.
1.1 This fire-test-response test method covers the determination under specified laboratory conditions of the combustibility of building materials. Materials passing this test are typically classified as noncombustible materials. 1.2 Limitations of this fire-test response test method are shown...
Narrow Your Results