loading
AGMA PLASTIC GEAR SET - AGMA PLASTIC GEAR SET
AGMA
A description is not available for this item.
ASTM E2905/E2905M-26 - Standard Practice for Examination of Mill and Kiln Girth Gear Teeth—Electromagnetic Methods
July 1, 2026 - ASTM International

Note 1: Throughout the practice, "gear" means gear or pinion unless the gear is specifically identified. 1.1 This practice describes a two-part procedure for examination of gear teeth on mill and kiln gear drives and pinions using eddy current array (ECA) methods....

ASTM F3835-26 - Standard Specification for Light Sport Category Aircraft Landing Gear Systems
May 1, 2026 - ASTM International

1.1 This specification covers minimum requirements for the design and testing of landing gear systems for light sport category aircraft. The landing gear system is considered to include all energy absorption elements and the primary supporting structures that carry the landing loads...

ASTM F3838-26 - Standard Specification for Light Sport Category Thrust Borne Aircraft Landing Gear Systems
May 1, 2026 - ASTM International

1.1 This specification covers minimum requirements for the design and testing of landing gear systems for light sport category thrust-borne aircraft. The landing gear system is considered to include all energy absorption elements and the primary supporting structures that carry the...

ASTM A788/A788M-26a - Standard Specification for Steel Forgings, General Requirements
August 1, 2026 - ASTM International

1.1 This specification covers a group of common requirements that, unless otherwise specified in the individual product specification, shall apply to steel forgings under any of the following specifications issued by ASTM: ASTM Designation Title A266/A266M Carbon Steel Forgings for Pressure Vessel...

ASTM D7483-26 - Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Oscillating Piston Viscometer
July 1, 2026 - ASTM International

5.1 Many petroleum products, as well as non-petroleum materials, are used as lubricants for bearings, gears, compressor cylinders, hydraulic equipment, etc. Proper operation of this equipment depends upon the viscosity of these liquids. 5.2 Oscillating piston viscometers allow viscosity...

ASTM D5182-26 - Standard Test Method for Evaluating the Scuffing Load Capacity of Oils (FZG A/8.3/90 Method)
May 1, 2026 - ASTM International

1.1 This test method, the Forschungstelle für Záhnräder und Getriebebau (Research Site for Gears and Transmissions) Visual Method, commonly referred to as the FZG Visual Method, is intended to measure the scuffing load capacity of oils used to lubricate hardened steel gears. Scoring,...

ASTM D3427-26 - Standard Test Method for Air Release Properties of Hydrocarbon Based Oils
June 1, 2026 - ASTM International

5.1 Agitation of lubricating oil with air in equipment, such as bearings, couplings, gears, pumps, and oil return lines, may produce a dispersion of finely divided air bubbles in the oil. If the residence time in the reservoir is too short to allow the air bubbles to rise to the oil surface,...

ASTM A788/A788M-26 - Standard Specification for Steel Forgings, General Requirements
July 1, 2026 - ASTM International

1.1 This specification covers a group of common requirements that, unless otherwise specified in the individual product specification, shall apply to steel forgings under any of the following specifications issued by ASTM: ASTM Designation Title A266/A266M Carbon Steel Forgings for Pressure Vessel...

ASTM A291/A291M-26 - Standard Specification for Steel Forgings, Carbon and Alloy, for Pinions, Gears and Shafts for Reduction Gears
April 1, 2026 - ASTM International

This specification covers normalized and tempered carbon steel, and liquid quenched and tempered alloy steel forgings for pinions, gears, and shafts for reduction gears. Prior to heat treatment for mechanical properties testing , steel materials may undergo machining and boring, after...

ASTM F2317/F2317M-26 - Standard Specification for Design of Weight-Shift-Control Aircraft
May 1, 2026 - ASTM International

This specification covers the minimum requirement for designing, testing, and labeling of weight-shift-control aircraft. This specification covers only weight-shift-control aircraft in which flight control systems do not use hinged surfaces controlled by the pilot. Flight requirements are specified...

ASTM F1449-20(2026) - Standard Guide for Industrial Laundering Care and Maintenance of Flame Resistant or Arc Rated Clothing
May 1, 2026 - ASTM International

1.1 This guide provides recommendations for the care and maintenance of clothing that is flame resistant or arc rated. 1.2 These recommendations address the industrial laundering process. Industrial laundering is an effective cleaning process for flame resistant or arc rated clothing; follow all...

ASTM F2757-20(2026) - Standard Guide for Home Laundering Care and Maintenance of Flame Resistant or Arc Rated Clothing
May 1, 2026 - ASTM International

1.1 This guide provides recommendations for home laundering of clothing that is flame resistant or arc rated. These recommendations address the home laundering process. Home laundering is an effective cleaning process for flame resistant or arc rated garments; follow all label care instructions. 1...

ASTM A290/A290M-26 - Standard Specification for Carbon and Alloy Steel Forgings for Rings for Reduction Gears
April 1, 2026 - ASTM International

1.1 This specification covers normalized and tempered, and quenched and tempered, carbon and alloy steel forged or rolled rings for reduction gears. 1.2 Several grades and classes of steel are covered as follows: 1.2.1 Grade 1, Classes A and B, and Grade 2, Classes C and D, are carbon steel....

ASTM A1038-26 - Standard Test Method for Portable Hardness Testing by the Ultrasonic Contact Impedance Method
February 15, 2026 - ASTM International

4.1 The hardness of a material is a defined quantity having many scales and being dependent on the way the test is performed. In order to avoid the creation of a new method involving a new hardness scale, the UCI method converts into common hardness values, for example, HV, HRC, etc. 4.2 The UCI...

ASTM D8315-26 - Standard Test Method for Determination of Wear Metals and Contamination Elements in Used Industrial Oils by Sweeping Flat Electrode Atomic Emission Spectrometry
March 1, 2026 - ASTM International

1.1 This test method covers the determination of wear metals and contaminants in used industrial oils by sweeping flat electrode atomic emission spectroscopy (SFE-AES). 1.2 Industrial oil includes lubricant oil, gear box oil, hydraulic fluid, compressor oil, turbine oil, synthetic oils, and...

ASTM D5182-25a - Standard Test Method for Evaluating the Scuffing Load Capacity of Oils (FZG Visual Method)
December 1, 2025 - ASTM International

1.1 This test method, the Forschungstelle für Záhnräder und Getriebebau (Research Site for Gears and Transmissions) Visual Method, commonly referred to as the FZG Visual Method, is intended to measure the scuffing load capacity of oils used to lubricate hardened steel gears. Scoring,...

ASTM D6821-25 - Standard Test Method for Low Temperature Viscosity of Drive Line Lubricants in a Constant Shear Stress Viscometer
November 1, 2025 - ASTM International

5.1 Viscosity of drive line lubricants at low temperature is critical for both gear lubrication and the circulation of the fluid in automatic transmissions. For gear oils (GOs), the issue is whether the fluid characteristics are such that the oil will flow into the channel dug out by...

ASTM E3348/E3348M-25 - Standard Guide for Body Armor for Non-Law Enforcement First Responders
October 15, 2025 - ASTM International

4.1 This guide is intended for non-law enforcement first responders facing increased exposure to scenes of violence where firearms or stabbing weapons may be used. 4.2 The use and wear conditions are different than for law enforcement, requiring specialized guidance on types of body armor and their...

Advertisement