Note 1: Throughout the practice, "gear" means gear or pinion unless the gear is specifically identified. 1.1 This practice describes a two-part procedure for examination of gear teeth on mill and kiln gear drives and pinions using eddy current array (ECA) methods....
1.1 This specification covers minimum requirements for the design and testing of landing gear systems for light sport category aircraft. The landing gear system is considered to include all energy absorption elements and the primary supporting structures that carry the landing loads...
1.1 This specification covers minimum requirements for the design and testing of landing gear systems for light sport category thrust-borne aircraft. The landing gear system is considered to include all energy absorption elements and the primary supporting structures that carry the...
1.1 This specification covers a group of common requirements that, unless otherwise specified in the individual product specification, shall apply to steel forgings under any of the following specifications issued by ASTM: ASTM Designation Title A266/A266M Carbon Steel Forgings for Pressure Vessel...
5.1 Many petroleum products, as well as non-petroleum materials, are used as lubricants for bearings, gears, compressor cylinders, hydraulic equipment, etc. Proper operation of this equipment depends upon the viscosity of these liquids. 5.2 Oscillating piston viscometers allow viscosity...
1.1 This test method, the Forschungstelle für Záhnräder und Getriebebau (Research Site for Gears and Transmissions) Visual Method, commonly referred to as the FZG Visual Method, is intended to measure the scuffing load capacity of oils used to lubricate hardened steel gears. Scoring,...
5.1 Agitation of lubricating oil with air in equipment, such as bearings, couplings, gears, pumps, and oil return lines, may produce a dispersion of finely divided air bubbles in the oil. If the residence time in the reservoir is too short to allow the air bubbles to rise to the oil surface,...
1.1 This specification covers a group of common requirements that, unless otherwise specified in the individual product specification, shall apply to steel forgings under any of the following specifications issued by ASTM: ASTM Designation Title A266/A266M Carbon Steel Forgings for Pressure Vessel...
This specification covers normalized and tempered carbon steel, and liquid quenched and tempered alloy steel forgings for pinions, gears, and shafts for reduction gears. Prior to heat treatment for mechanical properties testing , steel materials may undergo machining and boring, after...
This specification covers the minimum requirement for designing, testing, and labeling of weight-shift-control
1.1 This guide provides recommendations for the care and maintenance of clothing that is flame resistant or arc rated. 1.2 These recommendations address the industrial laundering process. Industrial laundering is an effective cleaning process for flame resistant or arc rated clothing; follow all...
1.1 This guide provides recommendations for home laundering of clothing that is flame resistant or arc rated. These recommendations address the home laundering process. Home laundering is an effective cleaning process for flame resistant or arc rated garments; follow all label care instructions. 1...
1.1 This specification covers normalized and tempered, and quenched and tempered, carbon and alloy steel forged or rolled rings for reduction gears. 1.2 Several grades and classes of steel are covered as follows: 1.2.1 Grade 1, Classes A and B, and Grade 2, Classes C and D, are carbon steel....
4.1 The hardness of a material is a defined quantity having many scales and being dependent on the way the test is performed. In order to avoid the creation of a new method involving a new hardness scale, the UCI method converts into common hardness values, for example, HV, HRC, etc. 4.2 The UCI...
1.1 This test method covers the determination of wear metals and contaminants in used industrial oils by sweeping flat electrode atomic emission spectroscopy (SFE-AES). 1.2 Industrial oil includes lubricant oil, gear box oil, hydraulic fluid, compressor oil, turbine oil, synthetic oils, and...
1.1 This test method, the Forschungstelle für Záhnräder und Getriebebau (Research Site for Gears and Transmissions) Visual Method, commonly referred to as the FZG Visual Method, is intended to measure the scuffing load capacity of oils used to lubricate hardened steel gears. Scoring,...
5.1 Viscosity of drive line lubricants at low temperature is critical for both gear lubrication and the circulation of the fluid in automatic transmissions. For gear oils (GOs), the issue is whether the fluid characteristics are such that the oil will flow into the channel dug out by...
4.1 This guide is intended for non-law enforcement first responders facing increased exposure to scenes of violence where firearms or stabbing weapons may be used. 4.2 The use and wear conditions are different than for law enforcement, requiring specialized guidance on types of body armor and their...
Narrow Your Results