loading
ASTM E998-19(2025) - Standard Test Method for Structural Performance of Architectural Glass Products Under the Influence of Uniform Static Loads
August 1, 2025 - ASTM International

5.1 This test method is a general procedure for testing architectural glass products under uniform static loads. 5.2 Loads on glass in windows, curtain walls, and doors may vary greatly in magnitude, direction, and duration. An understanding of wind loads on the building is...

NFGS 08371 - ALUMINUM SLIDING GLASS DOORS
NAVY
A description is not available for this item.
BS 5286 - Aluminium Framed Sliding Glass Doors
May 31, 1978 - BSI

Requirements for single and double glazed doors for general purposes. Excludes sliding folding doors, doors containing panels exceeding 1500 mm in length or 2400 mm in height, heavy duty doors for showrooms, etc.

ASTM F3427-25 - Standard Practice for Documenting Environmental Conditions for Utilization with Exoskeleton Test Methods
November 1, 2025 - ASTM International

4.1 This section provides a description of the environmental conditions listed in Section 1 and describes the sub-conditions within each condition. Examples provided for many of the conditions and sub-conditions are provided as guidance only. Each of the conditions described should be evaluated and...

ASTM F3218-25 - Standard Practice for Documenting Environmental Conditions for Utilization with Robotic, Automatic, or Autonomous System Test Methods
September 1, 2025 - ASTM International

4.1 This section provides a description of the environmental conditions listed in Section 1 and describes the sub-conditions within each condition. Examples provided for many of the conditions and sub-conditions are provided as guidance only. Each of the conditions described should be evaluated and...

ASTM F2912-25 - Standard Specification for Glazing and Glazing Systems Subject to Airblast Loadings
April 15, 2025 - ASTM International

1.1 This specification covers glazing, glazed windows, glazed curtain walls, glazing panels in doors, other glazed protective systems, and non-attached window retrofit systems used in buildings that may be subjected to intentional or accidental explosions. 1.2 This specification addresses...

ASTM E987-88(2024) - Standard Test Methods for Deglazing Force of Fenestration Products
October 1, 2024 - ASTM International

1.1 These test methods measure the resistance of elements of fenestration products such as operating (or removable) window sashes, storm sashes, and sliding glass door panels (hereafter referred to as sash members) to forces tending to deglaze the construction. 1.2 These test methods...

ASTM F1070-19(2024) - Standard Specification for Doors, Non-Tight, for Marine Use
May 1, 2024 - ASTM International

This specification covers the dimensional and mechanical requirements as well as the construction of steel, aluminum, and glass-reinforced plastic (GRP) non-tight, personnel doors and dutch doors for marine use. The door assembly shall be manufactured free of sharp and...

UL 907 - Fireplace Accessories
September 4, 2024 - ULSE

Fireplace Accessories UL 907 1.1 These requirements apply to fireplace accessories that are intended only for field installation into or attachment to existing masonry fireplaces. Fireplace accessories include items such as heat exchangers, glass door assemblies, and the like. For the...

GMW15663 - Door Window System Glass Wipe Area Determination
November 1, 2018 - GMW

Introduction Note: Nothing in this standard supercedes applicable laws and regulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence. Purpose. This test evaluates the glass wiping characteristics of door outer...

ASTM E547-00(2024) - Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Cyclic Static Air Pressure Difference
December 1, 2024 - ASTM International

1.1 This test method covers the determination of the resistance of exterior windows, curtain walls, skylights, and doors to water penetration when water is applied to the outdoor face and exposed edges simultaneously with a cyclic static air pressure at the outdoor face higher than the...

ASTM F1069-19(2024) - Standard Specification for Doors, Watertight, Gastight/Airtight and Weathertight, Individually Dogged, for Marine Use
May 1, 2024 - ASTM International

This specification covers the principal shapes and dimensions, and mechanical requirements for the manufacture of two types of individually dogged watertight, gastight/airtight, and weathertight doors of steel, aluminum, and glass-reinforced plastic construction. These doors,...

GMW15676 - Door Window System - Glass Scratch Durability
September 1, 2016 - GMW

Introduction Note: Nothing in this standard supercedes applicable laws and regulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence. Purpose. To determine the potential for the door glass to be scratched as a...

CSA A440.2 - ENERGY PERFORMANCE EVALUATION OF WINDOWS AND SLIDING GLASS DOORS
CSA
A description is not available for this item.
ASTM D4099-95 - Standard Specification for Poly(Vinyl Choride)(PVC) Prime Windows and Sliding Glass Doors (Withdrawn 1999)
January 1, 1995 - ASTM International

1.1 This specification establishes the requirements for material properties and performance characteristics for prime windows and sliding glass doors manufactured of rigid poly(vinyl chloride) (PVC). Windows and doors included in this specification shall be complete assemblies...

ASTM D4803-24 - Standard Test Method for Predicting Heat Buildup in PVC Building Products
February 1, 2024 - ASTM International

5.1 Heat buildup in PVC exterior building products due to absorption of the energy from the sun may lead to distortion problems. Heat buildup is affected by the color, emittance, absorptance, and reflectance of a product. Generally, the darker the color of the product, the more energy is absorbed...

IAPMO IGC 154 - Shower and Tub/Shower Enclosures, Bathtubs with Glass Pressure- Sealed Doors, and Shower/Steam Panels
January 1, 2019 - IAPMO

General This Standard covers shower/steam panels, enclosures for showers and tub/shower combinations, bathtubs and tub/shower combinations with glass pressure‐sealed doors, and floor‐mounted showers intended for new and retrofit applications and specifies requirements for materials,...

GMW15090 - Door Window System Glass Stability and Static Blowout Strength Test
February 1, 2017 - GMW

Introduction Note: Nothing in this standard supercedes applicable laws and regulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence. Purpose. To determine the dropping window system's glass stability and static blowout...

ASTM E331-00(2023) - Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference
February 1, 2023 - ASTM International

1.1 This test method covers the determination of the resistance of exterior windows, curtain walls, skylights, and doors to water penetration when water is applied to the outdoor face and exposed edges simultaneously with a uniform static air pressure at the outdoor face higher than the...

ASTM E2268-04(2023) - Standard Test Method for Water Penetration of Exterior Windows, Skylights, and Doors by Rapid Pulsed Air Pressure Difference
February 1, 2023 - ASTM International

1.1 This test method covers the determination of the resistance of exterior windows, skylights, and doors to water penetration when water is applied to the outdoor face and exposed edges simultaneously with a rapid pulsed air pressure at the outdoor face higher than the pressure at the...

Advertisement