INTRODUCTION MODEL PROJECT SPECIFICATION Fibrous glass duct shall be of type (475) (800) and shall be of 1 in. (25 mm) or 1½ in. (38 mm) thickness and conform to the SMACNA Fibrous Glass Duct Construction Standards, 7th Edition, 2003 or the NAIMA Fibrous Glass Duct Construction...
1.1 This test method covers procedures for testing the durability of preassembled, permanently sealed vacuum insulating glass (VIG) units. 1.2 This test method is applicable only to VIG units that are constructed with flat glass lites (glass panes). 1.3 This test method is...
1.1 This specification covers the aesthetic quality requirements for decorative enamels applied to flat glass for use in building glazing. 1.2 This specification covers the requirements for flat glass, with either organic or ceramic enamels applied. 1.2.1 Glass may be annealed,...
This specification covers the requirements for disposable glass culture tubes for use in culturing applications. Disposable glass culture tubes shall be made of type I (borosilicate) or type II (soda-lime) glass. Tube design shall be of one-piece construction. Other...
This specification covers disposable glass serological pipets, calibrated "to deliver," used in measuring volumes of liquids. Pipets shall be straight and have one-piece construction, fabricated from borosilicate glass, Type I, Class A or B; or soda-lime glass, Type II. Any...
This specification provides standard dimensional requirements for glass beakers suitable for general laboratory use. The glass beakers are classified into types and sizes and are presented in details. The glass beaker types are: type I - low form with spout; type II - low form,...
1.1 This specification covers standard dimensional requirements for obtaining, within practical limits, interchangeability in glass stopcocks (Note 1) with polytetrafluoroethyl
1.1 These test methods cover the chemical analysis of glass sands. They are useful for either high-silica sands (99?%+?silica (SiO2)) or for high-alumina sands containing as much as 12?% to 13?% alumina (Al2O3). Generally nonclassical, these test methods are rapid and accurate. They include...
This specification covers a disposable glass Westergren tube used for measuring the erythrocyte sedimentation rate. Covered by this specification are Type I (standard Westergren tube used in conventional racks only) and Type II (self-zeroing tubes used with racks that have convenient...
This specification describes the physical requirements and corresponding test methods for disposable glass blood sample capillary tubes for use in microhematocrit procedures. Covered here are two different types of capillary tubes, namely, Type I (coated with heparin), and Type II (uncoated)...
This specification covers reusable blood sedimentation tubes suitable for determining sedimentation rates and the volume of packed red blood cells. The tubes shall be fabricated from borosilicate glass, Type I, Class B, or sodalime glass, Type II. A resistance to centrifugal force...
This specification covers disposable blood sedimentation tubes suitable for determining sedimentation rates and the volume of packed red blood cells. This specification covers a tube intended for one-time use only. The tubes shall be fabricated borosilicate glass, Type I, Class B, or from...
1.1 This test method covers the determination of the annealing point and the strain point of a glass by measuring the viscous elongation rate of a fiber of the glass under prescribed condition. 1.2 The annealing and strain points shall be obtained by following the specified procedure...
1.1 This specification covers machine-made fiberglass pipe intended for use in gravity-flow systems for conveying sanitary sewage, storm water, and some industrial wastes. Both glass-fiber-reinforced thermosetting-resin pipe (RTRP) and glass-fiber-reinforced polymer mortar pipe (RPMP)...
5.1 Glass-fiber roving chopping rates, determined by this test method, are useful for quality control of GFRC products to ensure that manufacturing equipment has been set up to deliver the correct proportions of concrete and glass fiber reinforcement for producing a GFRC composite....
5.1 Slurry Flow Rates, determined by this test method, are useful for quality control of GFRC products to ensure that manufacturing equipment has been set up to deliver the correct proportions of concrete and glass fiber reinforcement for producing a GFRC composite. This test method is...
1.1 This specification covers the requirements for chemically strengthened glass products that are used in general building construction, transportation, solar energy, and other electronic applications, such as PC screens, notebooks, tablets, smart phones, and e-readers, as well as copy...
1.1 This specification covers prefabricated modified bituminous sheet materials reinforced with polyester fabric as the primary reinforcement, with or without granules, which use styrene butadiene styrene (SBS) thermoplastic elastomer as the primary modifier and are intended for use in the...
Narrow Your Results