This specification covers aggregates used for masonry grout. Aggregates should consist of either natural or manufactured sand, used alone or in combination with course aggregates. The course aggregates should be made up of crushed stone, gravel, or processed air-cooled iron blast-furnace...
3.1 Grout used in masonry is a fluid mixture of cementitious materials and aggregate with a high water content for ease of placement. 3.1.1 During construction, grout is placed within or between absorptive masonry units. Excess water must be removed from grout specimens in...
1.1 These test methods are intended to evaluate the chemical resistance of resin, silica, silicate, sulfur, and hydraulic materials, grouts, monolithic surfacings, and polymer concretes under anticipated service conditions. These test methods provide for the determination of changes in the...
1.1 This guide provides information regarding masonry elements constructed at locations other than in-place. Prefabrication may occur on the jobsite or offsite and transported to the jobsite. This guide covers lintels, arches, sloped sills, spandrels, soffits, wall panels, and other masonry...
5.1 Due to hydraulic pressure that may be present on some applications, engineers need to understand the capability of these products to resist this pressure. This test allows engineers to compare products and verify pullout strength. 5.2 Hydraulic pullout resistance is a function of locking...
4.1 This guide is intended to be used in the selection and installation of chemical grout to seal leaks in concrete walls, floors, and ceilings. The procedure described in this guide focuses on the injection of through-wall cracks, but may be adapted to cold joints, control joints, voids...
This specification covers filled epoxy-coated seven-wire prestressing steel strands with protective fusion-bonded epoxy coating applied by the electrostatic deposition method. This specification also covers relaxation loss limits for filled epoxy coated strands. Prestressing steel strands shall be...
3.1 Grout used in masonry is a fluid mixture of cementitious materials and aggregate with a high water content for ease of placement. 3.1.1 During construction, grout is placed within or between absorptive masonry units. Excess water must be removed from grout specimens in...
1.1 This test method covers procedures for the preparation, curing, transporting and testing of cylindrical test specimens of controlled low strength material (CLSM) for the determination of compressive strength. 1.2 This test method covers CLSM materials that have a higher strength than the soil...
1.1 This standard incorporates terms and definitions of terms used in standards under the jurisdiction of Committee C15 on Masonry - Manufactured Masonry Units, Mortars, and Grouts. 1.2 This standard incorporates terms and definitions of terms associated with the standards specific to clay...
1.1 These test methods cover procedures for static tensile and shear testing of post-installed and cast-in-place anchorage systems in members made of concrete or members made of solid, hollow, or grout-filled masonry and related materials. Tests may be made to determine the ultimate load or...
5.1 This test method provides a procedure to determine the total water content in a sample of a fresh hydraulic cementitious mixture by determining the change in mass of the sample after rapid evaporation using a furnace capable of maintaining an air temperature between 790 °C and 815 °C [1450 °F...
3.1 Grout used in masonry is a fluid mixture of cementitious materials and aggregate with a high water content for ease of placement. 3.1.1 During construction, grout is placed within or between absorptive masonry units. Excess water must be removed from grout specimens in...
1.1 This standard incorporates terms and definitions of terms used in standards under the jurisdiction of Committee C15 on Masonry - Manufactured Masonry Units, Mortars, and Grouts. 1.2 This standard incorporates terms and definitions of terms associated with the standards specific to clay...
1.1 This specification covers slag cement for use as a cementitious material in concrete and mortar. Note 1: The material described in this specification may be used to produce a blended cement meeting the requirements of Specification C595/C595M or as a separate ingredient in concrete or mortar...
1.1 These test methods provide procedures for measuring the temperature profile within a deep foundation element constructed using cast-in-place concrete, such as bored piles, drilled shafts, augered piles, diaphragm walls, barrettes, and alike. The thermal profile induced by the curing concrete...
3.1 Grout used in masonry is a fluid mixture of cementitious materials and aggregate with a high water content for ease of placement. 3.1.1 During construction, grout is placed within or between absorptive masonry units. Excess water must be removed from grout specimens in...
1.1 This practice describes the laboratory procedure for selecting proportions for grout mixtures required in the production of preplaced-aggregate (PA) concrete. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for...
4.1 A correctly designed, installed, and developed groundwater monitoring well, constructed in accordance with Practice D5092/D5092M should provide the following: representative samples of groundwater that can be analyzed to determine physical properties and water quality parameters of the sample...
This practice outlines the standard procedures for performing petrographic examination of hardened concrete samples. The samples examined may be taken from concrete constructions, that is, all sorts of objects, units, or structures that have been built of hydraulic cement concrete. They may also be...
Narrow Your Results