loading
ASTM D3902-90(2026) - Standard Test Method for Rubber Hose for Gas Diffusion of Liquefied Petroleum Gas
June 1, 2026 - ASTM International

2.1 Rubber hose has an inherent characteristic of permitting diffusion of a gas through the hose structure. This test method quantitatively measures the loss of liquefied petroleum gas.

ASTM E814-26 - Standard Test Method for Fire Tests of Penetration Firestop Systems
June 1, 2026 - ASTM International

5.1 This test method is used to determine the performance of a firestop system with respect to exposure to a standard time-temperature fire test and a hose stream test. The performance of a firestop system is dependent upon the specific assembly of materials tested including the number,...

ASTM E1419/E1419M-26 - Standard Practice for Examination of Seamless, Gas-Filled, Pressure Vessels Using Acoustic Emission
May 1, 2026 - ASTM International

5.1 Because of safety considerations, regulatory agencies (for example, U.S. Department of Transportation) require periodic examinations of vessels used in transportation of industrial gases (see Section 49, Code of Federal Regulations). The AE examination has become accepted as an alternative to...

ASTM D6513-26 - Standard Practice for Calculating the Superimposed Load on Wood-frame Walls for Standard Fire-Resistance Tests
April 1, 2026 - ASTM International

4.1 Test Methods E119 and E1529, and other standard fire resistance test methods specify that throughout exposures to fire and the hose stream, a constant superimposed axial load be applied to a load-bearing test specimen to simulate a maximum load condition. These test methods specify that...

ASTM E119-26 - Standard Test Methods for Fire Tests of Building Construction and Materials
January 1, 2026 - ASTM International

4.1 These test methods are intended to evaluate the duration for which the types of building elements noted in 1.1 contain a fire, retain their structural integrity, or exhibit both properties during a predetermined test exposure. 4.2 The test exposes a test specimen to a standard fire controlled...

ASTM E2226-25 - Standard Practice for Application of Hose Stream
April 1, 2025 - ASTM International

1.1 This practice is applicable to building elements required to be subjected to the impact, erosion, and cooling effects of a hose stream as part of a fire-test-response standard. Building elements include, but are not limited to, wall and partition assemblies, fire-resistive joint systems,...

ASTM E1198-25 - Standard Practice for Sampling Zooplankton with Pumps
September 1, 2025 - ASTM International

5.1 The advantages of collecting zooplankton with pumps are as follows: 5.1.1 Sample size is more accurately controlled than with nets. 5.1.2 Discrete samples can be more easily obtained both vertically and horizontally. 5.1.3 Multiple or replicate samples can be more easily obtained. 5.1.4 The...

ASTM D413-98(2025) - Standard Test Methods for Rubber Property—Adhesion to Flexible Substrate
September 1, 2025 - ASTM International

1.1 These test methods cover the determination of the adhesion strength between plies of fabric bonded with rubber or the adhesion of the rubber layer in articles made from rubber attached to other material. They are applicable only when the adhered surfaces are approximately plane or uniformly...

ASTM F2709-19(2025) - Standard Test Method for Determining a Measured Nameplate Recovery Rate of Stationary Oil Skimmer Systems
September 1, 2025 - ASTM International

4.1 It has been industry practice to claim the capacity of a skimmer based on the rate of the discharge pump (which are typically rated using water as a test fluid) or other arbitrary methods. 4.2 End users need a test methodology that evaluates optimum performance data for planning and selection...

ASTM E1930/E1930M-25 - Standard Practice for Examination of Liquid-Filled Atmospheric and Low-Pressure Metal Storage Tanks Using Acoustic Emission
September 1, 2025 - ASTM International

5.1 General-This procedure is used for evaluation of the structural integrity of atmospheric storage tanks. The AE method can detect flaws which are in locations that are stressed during pressurization. Such locations include the tank wall, welds attaching pads to the tank, nozzle attachments, and...

ASTM F1743-25 - Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP)
May 1, 2025 - ASTM International

4.1 This practice is for use by designers and specifiers, regulatory agencies, owners, and inspection organizations who are involved in the rehabilitation of conduits through the use of a resin-impregnated fabric tube pulled-in-place through an existing conduit and secondarily inflated through the...

ASTM E2226-24 - Standard Practice for Application of Hose Stream
November 1, 2024 - ASTM International

1.1 This practice is applicable to building elements required to be subjected to the impact, erosion, and cooling effects of a hose stream as part of a fire-test-response standard. Building elements include, but are not limited to, wall and partition assemblies, fire-resistive joint systems,...

ASTM E2336-25 - Standard Test Methods for Fire Resistive Grease Duct Enclosure Systems
April 1, 2025 - ASTM International

5.1 These test methods are intended to evaluate the ability of the grease duct enclosure system to do the following: 5.1.1 Resist the effects of a standardized fire exposure, 5.1.2 Retain its integrity, or 5.1.3 Exhibit both properties dependent upon the type of test assembly involved during a...

ASTM D4776/D4776M-25 - Standard Test Method for Adhesion of Tire Cords and Other Reinforcing Cords to Rubber Compounds by H-Test Procedure
February 1, 2025 - ASTM International

1.1 This test method covers the measurement of adhesion of reinforcing cords that are bonded to rubber compounds. This test method is applicable to textile cord structures from both natural and manmade fibers, other than steel. For adhesion testing of steel tire cords, refer to Test Method D2229. 1...

UL 2443 - Flexible Sprinkler Hose with Fittings for Fire Protection Service
August 26, 2024 - ULSE

1.1 This Standard covers flexible sprinkler hose with fittings intended for direct connection to fire sprinklers in installations requiring a flexible attachment to the sprinkler system piping such as clean rooms, suspended ceilings, and exhaust ducts. 1.2 The products covered by this...

ULC 2443 - Flexible Sprinkler Hose with Fittings for Fire Protection Service
August 26, 2024 - ULSE

1.1 This Standard covers flexible sprinkler hose with fittings intended for direct connection to fire sprinklers in installations requiring a flexible attachment to the sprinkler system piping such as clean rooms, suspended ceilings, and exhaust ducts. 1.2 The products covered by this...

ASTM F1743-24 - Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP)
November 1, 2024 - ASTM International

4.1 This practice is for use by designers and specifiers, regulatory agencies, owners, and inspection organizations who are involved in the rehabilitation of conduits through the use of a resin-impregnated fabric tube pulled-in-place through an existing conduit and secondarily inflated through the...

UL 330B - Hose and Hose Assemblies for Use With Dispensing Devices Dispensing Diesel Fuel, Biodiesel Fuel, Diesel/Biodiesel Blends With Nominal Biodiesel Concentrations Up To 20 Percent (B20), Kerosene, and Fuel Oil
May 31, 2024 - ULSE

1.1 These requirements cover hose and hose assemblies for use on dispensing devices for fuels. A flammable liquid hose assembly consists of flexible hose and fittings suitable for attachment to fuel dispensing equipment. Fuels, as defined by these requirements, include...

UL 2586B - Hose Nozzle Valves for Diesel Fuel, Biodiesel Fuel, Diesel/Biodiesel Blends with Nominal Biodiesel Concentrations up to 20 Percent (B20), Kerosene, and Fuel Oil
May 31, 2024 - ULSE

1.1 These requirements cover hose nozzle valves that are intended to be used for the control of motor fuels as indicated in 2. They are of the type used in motor fuel dispensing equipment. Hose nozzle valves covered by this standard are for use with motor fuels which are handled at...

ULC 2586B - Hose Nozzle Valves for Diesel Fuel, Biodiesel Fuel, Diesel/Biodiesel Blends with Nominal Biodiesel Concentrations up to 20 Percent (B20), Kerosene, and Fuel Oil
May 31, 2024 - ULSE

1.1 These requirements cover hose nozzle valves that are intended to be used for the control of motor fuels as indicated in 2. They are of the type used in motor fuel dispensing equipment. Hose nozzle valves covered by this standard are for use with motor fuels which are handled at...

Advertisement