loading
ASTM E2551-25 - Standard Test Methods for Humidity Calibration (or Conformation) of Humidity Generators for Use with Thermogravimetric Analyzers
December 1, 2025 - ASTM International

5.1 These test methods calibrate or demonstrate conformity of the humidity level in a purge gas generated by a humidity generator at a fixed temperature. Such calibration or demonstration of conformity may be required by quality initiatives. 5.2 Conformance demonstrates that the humidified...

ASTM C1355/C1355M-25 - Standard Specification for Glass Fiber Reinforced Gypsum Composites
April 1, 2025 - ASTM International

This specification covers glass fiber reinforced gypsum (GRG) composites suitable for producing GRG parts for non-loading bearings, thin sections, and ornamental shapes for architectural embellishment of interior building construction. Both the neat alpha gypsum cement and the resulting composite...

ASTM C1576-25 - Standard Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress Flexural Testing (Stress Rupture) at Ambient Temperature
February 1, 2025 - ASTM International

1.1 This test method covers the determination of slow crack growth (SCG) parameters of advanced ceramics by using a series of constant stress flexural tests in which the times-to-failure of four-point-1/4-point flexure test specimens (see Fig. 1) are determined as a function of different levels of...

ASTM C473-24 - Standard Test Methods for Physical Testing of Gypsum Panel Products
December 1, 2024 - ASTM International

These test methods cover the physical testing of gypsum panel products. The test methos appear in the following order: (1) flexural strength (Method A); (2) core, end, and edge hardness (Method A); (3) nail pull resistance (Method A); (4) humidified deflection; (5) end squareness; (6)...

ASTM C318/C318M-24 - Standard Specification for Gypsum Formboard
October 1, 2024 - ASTM International

This specification covers the minimum requirements for gypsum formboard designed for use as a permanent form for poured-in-place reinforced gypsum concrete roof decks. Gypsum formboard shall consist of a noncombustible core, essentially gypsum, either mineral or organic, synthetic or natural. The...

ASTM C1658/C1658M-19(2024) - Standard Specification for Glass Mat Gypsum Panels
October 15, 2024 - ASTM International

This specification covers the glass mat gypsum panels. Glass mat interior gypsum panel, designed for use on walls, ceilings, or partitions and that affords a surface suitable to receive decoration. Glass mat coreboard gypsum panel, and glass mat shaftliner gypsum panel, designed for use as a base...

ASTM F2140-24 - Standard Test Method for Performance of Hot Food Holding Cabinets
September 1, 2024 - ASTM International

5.1 The energy input rate and thermostat calibration tests are used to confirm that the hot food holding cabinet is operating properly prior to further testing. 5.2 Preheat energy and time can be useful to food service operators to manage energy demands and to know how quickly the hot food holding...

ASTM C1396/C1396M-24 - Standard Specification for Gypsum Board
October 1, 2024 - ASTM International

This specification covers gypsum boards which include the following: gypsum wallboard for use on walls, ceilings, or partitions and that affords a surface suitable to receive decoration; predecorated gypsum board for use as the finished surfacing for walls, ceilings, or partitions; gypsum backing...

ASTM C1177/C1177M-24 - Standard Specification for Glass Mat Gypsum Substrate for Use as Sheathing
April 1, 2024 - ASTM International

This specification covers the requirements for glass mat gypsum substrates designed to be used as exterior substrate or sheathing for weather barriers. The substrates shall consist of a noncombustible water-resistant gypsum core, surfaced with glass mat partially or completely embedded in the core....

ASTM C1178/C1178M-24 - Standard Specification for Coated Glass Mat Water-Resistant Gypsum Backing Panel
May 1, 2024 - ASTM International

This specification covers coated glass mat water-resistant gypsum backing panel designed for use on ceilings and walls in bath and shower areas as a base for the application of ceramic or plastic tile. Coated glass mat water-resistant gypsum backing panel shall consist of a noncombustible...

UL 60335-2-40 - Household and Similar Electrical Appliances - Safety - Part 2-40: Particular Requirements for Electrical Heat Pumps, Air-Conditioners and Dehumidifiers
December 15, 2022 - ULSE

This clause of Part 1 is replaced by the following. This part of IEC 60335 deals with the safety of electric heat pumps , including sanitary hot water heat pumps , air conditioners , and dehumidifiers incorporating motor-compressors and hydronic fan coils units , their maximum rated voltages being...

ASTM D6646-03(2022) - Standard Test Method for Determination of the Accelerated Hydrogen Sulfide Breakthrough Capacity of Granular and Pelletized Activated Carbon
September 1, 2022 - ASTM International

1.1 This test method is intended to evaluate the performance of virgin, newly impregnated or in-service, granular or pelletized activated carbon for the removal of hydrogen sulfide from an air stream, under the laboratory test conditions described herein. A humidified air stream containing...

ASTM D6332-12(2021) - Standard Guide for Testing Systems for Measuring Dynamic Responses of Carbon Monoxide Detectors to Gases and Vapors
September 1, 2021 - ASTM International

5.1 This guide provides information on testing systems and their components used for measuring responses of CO alarms or detectors subjected to gases, vapors, and their mixtures. Components of a testing system include a chamber, clean air supply module, humidification module, gas and vapor...

ASTM D5466-21 - Standard Test Method for Determination of Volatile Organic Compounds in Atmospheres (Canister Sampling, Mass Spectrometry Analysis Methodology)
August 15, 2021 - ASTM International

5.1 VOCs are emitted into ambient, indoor, and workplace air from many different sources. These VOCs are of interest for a variety of reasons including participation in atmospheric chemistry and contributing to air toxics with their associated acute or chronic health impacts. 5.2 Canisters are...

IEC 60335-2-53 - Household and similar electrical appliances – Safety – Part 2-53: Particular requirements for sauna heating appliances and infrared cabins
March 1, 2021 - IEC

This International Standard deals with the safety of electric sauna heating appliances and infrared emitting units having a rated power input not exceeding 20 kW, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. The appliances covered by this...

AIR1609B - Aircraft Humidification
January 14, 2021 - SAE International

This SAE Aerospace Information Report (AIR) covers the design parameters for various methods of humidification applicable to aircraft, the physiological aspects of low humidities, the possible benefits of controlling cabin humidity, the penalties associated with humidification, and...

DS/ISO 80601-2-69 - Medical electrical equipment – Part 2-69: Particular requirements for the basic safety and essential performance of oxygen concentrator equipment
November 23, 2020 - DS

This document specifies requirements for the basic safety and essential performance of an oxygen concentrator in combination with its accessories, hereafter referred to as ME equipment, intended to increase the oxygen concentration of gas intended to be delivered to a single patient. Such oxygen...

CEI EN IEC 63086-1 - Household and similar electrical air cleaning appliances - Methods for measuring the performance Part 1: Genereal requirements
December 1, 2020 - CEI

This part of IEC 63086 applies to electrically powered household and similar air cleaners intended for use on rated single-phase AC input voltage circuits not exceeding 250 V and DC input voltage circuits not exceeding 48 V. NOTE 1 See Clause 4 for examples of different technologies and placements...

ISO 80601-2-69 - Medical electrical equipment — Part 2-69: Particular requirements for the basic safety and essential performance of oxygen concentrator equipment
November 1, 2020 - ISO

This document specifies requirements for the basic safety and essential performance of an oxygen concentrator in combination with its accessories, hereafter referred to as ME equipment, intended to increase the oxygen concentration of gas intended to be delivered to a single patient. Such oxygen...

UL 998 - Humidifiers
April 9, 2020 - ULSE

1.1 These requirements cover humidifiers rated 600 V or less, and intended to be used in accordance with the National Electrical Code (NEC), ANSI/NFPA 70, and the rules of CSA C22.1, Canadian Electrical Code (CEC), Part I. 1.2 These requirements cover humidifiers intended for...

Advertisement