loading
HYDRAULICS - HYDRAULICS OF PIPELINES: PUMPS, VALVES, CAVITATION, TRANSLENTS
HI/HYDRAUL
A description is not available for this item.
ASTM D7898-14(2025) - Standard Practice for Lubrication and Hydraulic Filter Debris Analysis (FDA) for Condition Monitoring of Machinery
December 1, 2025 - ASTM International

1.1 This practice is intended to cover the extraction, analysis, and information management pertaining to visible wear debris collected from oil system filters or debris retention screens. Further, it is intended that this practice be a practical reference for those involved in FDA. 1.2 The...

QPL-24402 - Filters (Hydraulic), Filter Elements, and Filter Differential Pressure Indicators, General Specification for
August 3, 2018 - NPFC

QUALIFIED PRODUCT LIST OF PRODUCTS QUALIFIED UNDER PERFORMANCE SPECIFICATION MIL-DTL-24402 Filters (Hydraulic), Filter Elements, and Filter Differential Pressure Indicators, General Specification for This list has been prepared for use by or for the Government in the...

ISO 14085-2 - Aerospace series - Hydraulic filter elements - Test methods - Part 2: Conditioning
March 1, 2015 - ISO

This part of ISO 14085 specifies - a procedure to thermally condition a hydraulic filter element to presumed aerospace hydraulic system stresses, - a test procedure to complete cold soaks, hot soaks, and temperature variation in a combined manner, and - a test procedure to...

ASTM D7919-26 - Standard Guide for Filter Debris Analysis (FDA) Using Manual or Automated Processes
June 1, 2026 - ASTM International

1.1 This guide pertains to removal and analysis techniques to extract debris captured by in-service lubricant and hydraulic filters and to analyze the debris removed. 1.2 This guide suggests techniques to remove, collect and analyze debris from filters in support of machinery...

ASTM D8277-25 - Standard Test Method for Wet Filterability of Lubricants and Hydraulic Fluids by Mass Flow Technique
April 1, 2025 - ASTM International

1.1 This test method covers determination of the wet filterability of lubricants and hydraulic fluids based upon mass flow rate measurements through a 0.8?μm membrane after ageing of the fluid in the presence of water. The procedure applies to lubricants and hydraulic fluids...

ASTM D7898-14(2020) - Standard Practice for Lubrication and Hydraulic Filter Debris Analysis (FDA) for Condition Monitoring of Machinery
November 1, 2020 - ASTM International

1.1 This practice is intended to cover the extraction, analysis, and information management pertaining to visible wear debris collected from oil system filters or debris retention screens. Further, it is intended that this practice be a practical reference for those involved in FDA. 1.2 The...

ASTM D7752-26 - Standard Practice for Evaluating Compatibility of Mixtures of Hydraulic Fluids
March 1, 2026 - ASTM International

5.1 Hydraulic fluid compatibility is important to hydraulic equipment users because a mixture of incompatible fluids may produce a substance that is markedly inferior to its constituents. Even in identical base stocks, the formation of a precipitate may occur as a result of additive...

ASTM D8112-26 - Standard Guide for Sampling, In-Service Lubricating Oils and Hydraulic Fluids in Industrial Applications
May 1, 2026 - ASTM International

5.1 Analyzing in-service lubricating oil and hydraulic fluid samples is crucial for assessing the condition of both the fluid and the equipment. The results of the fluid analysis guide the planning of any necessary corrective maintenance activities. 5.2 The objective of this guide is to...

ISO 14085-6 - Aerospace series - Hydraulic filter elements - Test methods - Part 6: Initial cleanliness level
March 1, 2015 - ISO

This part of ISO 14085 defines a reference method for determining the level of cleanliness of new filter elements for use in aircraft hydraulic systems, after production prior to shipment, or prior to installation in the circuit. It applies to filter elements used on systems...

ISO 14085-1 - Aerospace series - Hydraulic filter elements - Test methods - Part 1: Test sequence
March 1, 2015 - ISO

This part of ISO 14085 specifies a test sequence for evaluation of characteristics of the hydraulic fluid filter elements under standard conditions. This part of ISO 14085 is not intended to qualify a filter element under replicate conditions of service; this can only be done...

ASTM D6884-26 - Standard Practice for Installation of Articulating Concrete Block (ACB) Revetment Systems
March 15, 2026 - ASTM International

5.1 An articulating concrete block system is comprised of a matrix of individual concrete blocks placed together to form an erosion-resistant system with specific hydraulic performance characteristics. These systems in practice are commonly referred to as ACB revetment systems. The system...

ASTM C204-26 - Standard Test Methods for Fineness of Hydraulic Cement by Air-Permeability Apparatus
May 1, 2026 - ASTM International

1.1 These test methods cover determination of the fineness of hydraulic cement, using the Blaine air-permeability apparatus, in terms of the specific surface expressed as total surface area in square centimeters per gram, or square meters per kilogram, of cement. Two test methods are given:...

ISO 16908 - Hydraulic filter element test methods - Thermal conditioning and cold start-up simulation
September 1, 2014 - ISO

This International Standard specifies a test procedure to thermally condition a hydraulic filter element and simulate cold start, such as that which can be encountered in mobile machinery applications. It is intended to provide a procedure that yields reproducible results and can be...

ISO 14085-4 - Aerospace series - Hydraulic filter elements - Test methods - Part 4: Verification of collapse/burst pressure rating
March 1, 2015 - ISO

This part of ISO 14085 describes a method for verifying the collapse/burst pressure rating of an aerospace hydraulic fluid power filter element. This represents the capability of a filter element to withstand a designated differential pressure in the normal (intended) direction...

BS ISO 14085-2 - Aerospace series — Hydraulic filter elements — Test methods Part 2: Conditioning
March 31, 2015 - BSI
A description is not available for this item.
ISO 14085-3 - Aerospace series - Hydraulic filter elements - Test methods - Part 3: Filtration efficiency and retention capacity
March 1, 2015 - ISO

This part of ISO 14085 describes two methods to measure in repeatable conditions the filtration efficiency of filter elements used in aviation and aerospace hydraulic fluid systems. It can be applied when evaluating the overall characteristics of a filter element per ISO...

ASTM D5782-18(2026) - Standard Guide for Use of Direct Air-Rotary Drilling for Geoenvironmental Exploration and the Installation of Subsurface Water-Quality Monitoring Devices
March 1, 2026 - ASTM International

4.1 The application of direct air-rotary drilling to geoenvironmental exploration may involve sampling, coring, in situ or pore-fluid testing, installation of casing for subsequent drilling activities in unconsolidated or consolidated materials, and for installation of subsurface water-quality...

ISO 14085-5 - Aerospace series - Hydraulic filter elements - Test methods - Part 5: Resistance to flow fatigue
March 1, 2015 - ISO

This part of ISO 14085 specifies a method for determining the resistance of a filter element to flow fatigue caused by varying flow through the filter in various stages of the filter contaminant loading process. The filter is subjected to a uniform varying flow rate for...

ASTM D6913/D6913M-17(2025) - Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis
October 1, 2025 - ASTM International

5.1 The gradation of the soil is used for classification in accordance with Practice D2487. 5.2 The gradation (particle-size distribution) curve is used to calculate the coefficient of uniformity and the coefficient of curvature. 5.3 Selection and acceptance of fill materials are often based on...

Advertisement