1.1 This practice is intended to cover the extraction, analysis, and information management pertaining to visible wear debris collected from oil system filters or debris retention screens. Further, it is intended that this practice be a practical reference for those involved in FDA. 1.2 The...
QUALIFIED PRODUCT LIST OF PRODUCTS QUALIFIED UNDER PERFORMANCE SPECIFICATION MIL-DTL-24402 Filters (Hydraulic), Filter Elements, and Filter Differential Pressure Indicators, General Specification for This list has been prepared for use by or for the Government in the...
This part of ISO 14085 specifies - a procedure to thermally condition a hydraulic filter element to presumed aerospace hydraulic system stresses, - a test procedure to complete cold soaks, hot soaks, and temperature variation in a combined manner, and - a test procedure to...
1.1 This guide pertains to removal and analysis techniques to extract debris captured by in-service lubricant and hydraulic filters and to analyze the debris removed. 1.2 This guide suggests techniques to remove, collect and analyze debris from filters in support of machinery...
1.1 This test method covers determination of the wet filterability of lubricants and hydraulic fluids based upon mass flow rate measurements through a 0.8?μm membrane after ageing of the fluid in the presence of water. The procedure applies to lubricants and hydraulic fluids...
1.1 This practice is intended to cover the extraction, analysis, and information management pertaining to visible wear debris collected from oil system filters or debris retention screens. Further, it is intended that this practice be a practical reference for those involved in FDA. 1.2 The...
5.1 Hydraulic fluid compatibility is important to hydraulic equipment users because a mixture of incompatible fluids may produce a substance that is markedly inferior to its constituents. Even in identical base stocks, the formation of a precipitate may occur as a result of additive...
5.1 Analyzing in-service lubricating oil and hydraulic fluid samples is crucial for assessing the condition of both the fluid and the equipment. The results of the fluid analysis guide the planning of any necessary corrective maintenance activities. 5.2 The objective of this guide is to...
This part of ISO 14085 defines a reference method for determining the level of cleanliness of new filter elements for use in aircraft hydraulic systems, after production prior to shipment, or prior to installation in the circuit. It applies to filter elements used on systems...
This part of ISO 14085 specifies a test sequence for evaluation of characteristics of the hydraulic fluid filter elements under standard conditions. This part of ISO 14085 is not intended to qualify a filter element under replicate conditions of service; this can only be done...
5.1 An articulating concrete block system is comprised of a matrix of individual concrete blocks placed together to form an erosion-resistant system with specific hydraulic performance characteristics. These systems in practice are commonly referred to as ACB revetment systems. The system...
1.1 These test methods cover determination of the fineness of hydraulic cement, using the Blaine air-permeability apparatus, in terms of the specific surface expressed as total surface area in square centimeters per gram, or square meters per kilogram, of cement. Two test methods are given:...
This International Standard specifies a test procedure to thermally condition a hydraulic filter element and simulate cold start, such as that which can be encountered in mobile machinery applications. It is intended to provide a procedure that yields reproducible results and can be...
This part of ISO 14085 describes a method for verifying the collapse/burst pressure rating of an aerospace hydraulic fluid power filter element. This represents the capability of a filter element to withstand a designated differential pressure in the normal (intended) direction...
This part of ISO 14085 describes two methods to measure in repeatable conditions the filtration efficiency of filter elements used in aviation and aerospace hydraulic fluid systems. It can be applied when evaluating the overall characteristics of a filter element per ISO...
4.1 The application of direct air-rotary drilling to geoenvironmental exploration may involve sampling, coring, in situ or pore-fluid testing, installation of casing for subsequent drilling activities in unconsolidated or consolidated materials, and for installation of subsurface water-quality...
This part of ISO 14085 specifies a method for determining the resistance of a filter element to flow fatigue caused by varying flow through the filter in various stages of the filter contaminant loading process. The filter is subjected to a uniform varying flow rate for...
5.1 The gradation of the soil is used for classification in accordance with Practice D2487. 5.2 The gradation (particle-size distribution) curve is used to calculate the coefficient of uniformity and the coefficient of curvature. 5.3 Selection and acceptance of fill materials are often based on...
Narrow Your Results