4.1 Laser profiling assessment is a quality control tool for identifying and quantifying deformation, physical damage, and other pipe anomalies after installation, providing means and methods for determining the quality of workmanship and compliance with project specifications. Laser...
4.1 Laser profiling assessment is a quality control tool for identifying and quantifying deformation, physical damage, and other pipe anomalies after installation, providing means and methods for determining the quality of workmanship and compliance with project specifications. Laser...
5.1 It is important to recognize that the results obtained by this test method or any other method for particle size determination utilizing different physical principles may disagree. The results are strongly influenced by physical principles employed by each method of particle size analysis. The...
1.1 This test method covers the determination of particle size distribution of alumina or quartz using laser light-scattering instrumentation in the range from 0.1 μm to 500 μm. 1.2 The procedure described in this test method may be applied to other nonplastic ceramic powders. It is at the...
1.1 This test method describes a means for quantitative determination of wear debris found in in-service lubricants by laser-induced breakdown spectroscopy (LIBS). LIBS is an analytical technology that uses short laser pulses to create micro hot-plasma ablation of a material and then...
4.1 The safety margins provided in the design for a component or structure can be reduced throughout its service life by aging. Aging is the process by which the physical and mechanical characteristics of component or structure materials change with time or use; this process may proceed by a single...
This specification covers the detailed requirements for specified grades of flat-rolled, grain-oriented, fully processed low-carbon silicon-iron electrical steels, whose low core loss and high permeability in the direction of rolling have been achieved by appropriate metallurgical processing. These...
?This document specifies the features of laser-based powder bed fusion of polymers (LB-PBF-P) and provides detailed design recommendations. ?Some of the fundamental principles are also applicable to other additive manufacturing (AM) processes, provided that due consideration is given to...
5.1 The freezing point of an aviation fuel is the lowest temperature at which the fuel remains free of solid hydrocarbon crystals which, if present in the fuel system of the aircraft, can restrict the flow of fuel through filters. The temperature of the fuel in the aircraft tank normally decreases...
1.1 This guide: 1.1.1 Collates information from existing standardized and non-standardized techniques and explains how the selected test methods can be adopted for contamination detection. 1.1.2 Defines contamination types that may be present within metal powders used in Laser Beam Powder...
5.1 The freezing point of an aviation fuel is the lowest temperature at which the fuel remains free of solid hydrocarbon crystals which, if present in the fuel system of the aircraft, can restrict the flow of fuel through filters. The temperature of the fuel in the aircraft tank normally decreases...
1.1 Many contaminants (such as petroleum products and coal tar) are emplaced in sediment in the form of an immiscible liquid, known as a non-aqueous phase liquid (NAPL). NAPL can either be a light non-aqueous phase liquid (LNAPL) that is less dense than water or a dense non-aqueous phase liquid...
1.1 This test method covers the determination of the molar mass of chitosan and chitosan salts intended for use in biomedical and pharmaceutical applications as well as in tissue-engineered medical products (TEMPs) by size exclusion chromatography with multi-angle laser light scattering...
4.1 This section provides a description of the environmental conditions listed in Section 1 and describes the sub-conditions within each condition. Examples provided for many of the conditions and sub-conditions are provided as guidance only. Each of the conditions described should be evaluated and...
1.1 This specification covers additively manufactured cobalt-28 chromium-6 molybdenum alloy components with similar chemical composition to UNS R30075 by means of laser and electron beam-based full melt powder bed fusion processes. The components produced by these processes are used...
1.1 This guide covers the application of laser-based ceilometers to measure local mixing layer heights (MLH). 1.2 The MLH measurements are expressed in SI units. No other units of measurement are used in this guide. 1.3 The applicability of specific regulatory limitations and criteria is not...
1.1 This practice for the safe application of 3D imaging technology will focus primarily on the application of specific technology components common to 3D imaging systems. When appropriate, reference may be made to existing standards written for said technologies. 1.2 Safety standards relevant to...
Narrow Your Results