loading
GMW17213 - Washer Reservoir Level Sensor Component Specification
April 1, 2020 - GMW

Purpose. The purpose of this test is to evaluate the performance of the washer reservoir level sensor on a component level.

GMW17491 - Fuel Pump Module Ultrasonic Fuel Level Sensor
August 1, 2019 - GMW
A description is not available for this item.
GMW15646 - Usable Fuel Volume vs. Level Sensor Resistance
August 1, 2019 - GMW
A description is not available for this item.
GME L/R-6G4-1 - OIL LEVEL SENSOR
GME
A description is not available for this item.
GMN6448 - FUEL TANK LEVEL SENSOR OUTPUT
GMNA
A description is not available for this item.
ASTM F3833-26 - Standard Guide for Computer Based Control Systems (CBCS)
May 1, 2026 - ASTM International

1.1 This guide defines the system-level behaviors for computer-based control of major, hazardous, and catastrophic failure conditions. The approaches identified provide behaviors intended to implement the necessary and sufficient controls for each specific failure condition being controlled....

ASTM F3827-26 - Standard Specification for Indirect Flight Controls
May 1, 2026 - ASTM International

1.1 This specification covers requirements for Indirect Flight Controls (IFC) equipment in light sport category aircraft. It recognizes there are three fundamental pilot functions of aviate, navigate, and communicate. This specification addresses the aviate function, which is the function of...

GME QT 126533 PART 5 - CHECK CONTROL PART 5: OIL LEVEL SENSOR
GME
A description is not available for this item.
ASTM E3057-26 - Standard Test Method for Measuring Heat Flux Using Directional Flame Thermometers with Advanced Data Analysis Techniques
January 1, 2026 - ASTM International

1.1 This test method describes the continuous measurement of the hemispherical heat flux to one or both surfaces of an uncooled sensor called a "Directional Flame Thermometer" (DFT). 1.2 DFTs consist of two heavily oxidized, Inconel 600 plates with mineral insulated, metal-sheathed (MIMS)...

ASTM D8084-26 - Standard Test Method for Photoelectrochemical Oxygen Demand of Freshwater Sources for Drinking Water Treatment Plants and Treated Drinking Water
January 1, 2026 - ASTM International

1.1 This test method covers a protocol for the determination of the photoelectrochemical oxygen demand of freshwater sources for drinking water treatment plants and treated drinking water in the range of 0.7 mg/L to 20 mg/L. Higher levels may be determined by sample dilution. 1.2...

ASTM F3427-25 - Standard Practice for Documenting Environmental Conditions for Utilization with Exoskeleton Test Methods
November 1, 2025 - ASTM International

4.1 This section provides a description of the environmental conditions listed in Section 1 and describes the sub-conditions within each condition. Examples provided for many of the conditions and sub-conditions are provided as guidance only. Each of the conditions described should be evaluated and...

ASTM E3132/E3132M-17(2025) - Standard Practice for Evaluating Response Robot Logistics: System Configuration
November 1, 2025 - ASTM International

5.1 These basic requirements for response robots that help enhance the safety and effectiveness of responders or soldiers include: the robots are designed to be remotely operated from safe standoff distances, deployable at operational tempos, capable of operating in complex environments,...

ASTM E1211/E1211M-17(2025) - Standard Practice for Leak Detection and Location Using Surface-Mounted Acoustic Emission Sensors
July 1, 2025 - ASTM International

1.1 This practice describes a passive method for detecting and locating the steady state source of gas and liquid leaking out of a pressurized system. The method employs surface-mounted acoustic emission sensors (for non-contact sensors see Practice E1002), or sensors attached...

ASTM F3705-25 - Standard Guide for Testing Detect and Avoid Systems for Unmanned Aircraft Systems
December 1, 2025 - ASTM International

1.1 This guide applies to unmanned aircraft (UA) with a maximum dimension (for example, wingspan, disk diameter) =?25?ft (=?7.68 m) operating at airspeeds below 100?kts and of any configuration or category. It is meant to be applied in a "lower risk" (low- and medium-risk airspace as described by...

ASTM F3287-17(2025) - Standard Test Method for Nondestructive Detection of Leaks in Packages by Mass Extraction Method
October 1, 2025 - ASTM International

1.1 This method provides a nondestructive means to detect holes (leaks) in a variety of non-porous rigid and semi-rigid packages. 1.2 This test method detects package leaks by measuring the mass flow extracted from a package while the package is enclosed inside an evacuated test chamber. The test...

ASTM E1930/E1930M-25 - Standard Practice for Examination of Liquid-Filled Atmospheric and Low-Pressure Metal Storage Tanks Using Acoustic Emission
September 1, 2025 - ASTM International

1.1 This practice covers guidelines for acoustic emission (AE) examinations of new and in-service aboveground storage tanks of the type used for storage of liquids. 1.2 This practice will detect acoustic emission in areas of sensor coverage that are stressed during the course of the...

ASTM D6245-25 - Standard Guide on the Relationship of Indoor Carbon Dioxide Concentrations to Indoor Air Quality and Ventilation
September 1, 2025 - ASTM International

5.1 Indoor CO2 concentrations have been used as indicators of IAQ for many years, involving both appropriate and inappropriate interpretations of indoor CO2 concentrations (1).5 Appropriate uses include estimating expected levels of occupant comfort in terms of human body odor perception,...

ASTM F3263-17(2025) - Standard Guide for Packaging Test Method Validation
October 1, 2025 - ASTM International

4.1 Addressing consensus standards with inter-laboratory studies (ILS) and methods specific to an organization. Test methods need to be validated in many cases, in order to be able to rely on the results. This has to be done at the organization performing the tests but is also performed in the...

ASTM E2863-25 - Standard Practice for Acoustic Emission Examination of Welded Steel Sphere Pressure Vessels Using Thermal Pressurization
September 1, 2025 - ASTM International

1.1 This practice is commonly used for periodic inspection and testing of welded steel gaseous spheres (bottles) with the acoustic emission (AE) method. AE is used in place of hydrostatic volumetric expansion testing. The periodic inspection and testing of bottles by AE testing is achieved without...

ASTM F3218-25 - Standard Practice for Documenting Environmental Conditions for Utilization with Robotic, Automatic, or Autonomous System Test Methods
September 1, 2025 - ASTM International

4.1 This section provides a description of the environmental conditions listed in Section 1 and describes the sub-conditions within each condition. Examples provided for many of the conditions and sub-conditions are provided as guidance only. Each of the conditions described should be evaluated and...

Advertisement