loading
IIAR ARM PROGRAM - ARM-Ammonia Refrigeration Management Program
IIAR

As the leading authority on ammonia refrigeration, the International Institute of Ammonia Refrigeration developed the Ammonia Refrigeration Management (ARM) Program to help small facilities improve safety, enhance system reliability and assist with regulatory compliance. ARM is...

ASTM D256-26 - Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
April 1, 2026 - ASTM International

5.1 Before proceeding with these test methods, refer to the specification of the material being tested. Any test specimen preparation, conditioning, dimensions, and testing parameters covered in the materials specification shall take precedence over those mentioned in these test methods. If there...

ASTM F3756-26 - Standard Practice for Grasp-Type Robot End-Effectors: Split Force Measurement Apparatus
February 1, 2026 - ASTM International

1.1 This practice covers a split-force measurement apparatus (SFMA), a measurement system that uses split geometries and load cells to quantify the force of a grasp and external forces applied to an object under grasp. The SFMA supports a series of standard performance test methods for...

ASTM F3295-18(2026) - Standard Guide for Impingement Testing of Total Disc Prostheses
January 1, 2026 - ASTM International

5.1 This guide can be used to develop test parameters for evaluating fatigue and wear behavior of IVD prostheses under impingement loading. It must be recognized, however, that there are likely many possible impingement conditions for a given IVD prosthesis. 5.2 The user should attempt to...

ASTM F3218-25 - Standard Practice for Documenting Environmental Conditions for Utilization with Robotic, Automatic, or Autonomous System Test Methods
September 1, 2025 - ASTM International

1.1 This practice describes "System" as a robotic, automatic, or autonomous system (for example, robot arm; automatic machine; automatic, automated, or autonomous?-?uncrewed ground vehicle (A-UGV)). When conducting test methods, it is important to consider the role that the environmental...

ASTM F3023-18(2025) - Standard Test Methods for Evaluating Design and Performance Characteristics of Stationary Upright and Recumbent Exercise Bicycles and Upper and Total Body Ergometers
February 1, 2025 - ASTM International

1.1 These test methods specify procedures and equipment used for testing and evaluating stationary exercise upright and recumbent bicycles and ergometers for compliance to Specification F1250. Both design and operational parameters will be evaluated. Where possible and applicable, accepted test...

ASTM F3756-25 - Standard Practice for Grasp-Type Robot End-Effectors: Split Force Measurement Apparatus
March 15, 2025 - ASTM International

1.1 This practice covers a split-force measurement apparatus (SFMA), a measurement system that uses split geometries and load cells to quantify the force of a grasp and external forces applied to an object under grasp. The SFMA supports a series of standard performance test methods for...

ASTM D256-24 - Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
December 1, 2024 - ASTM International

5.1 Before proceeding with these test methods, reference should be made to the specification of the material being tested. Any test specimen preparation, conditioning, dimensions, and testing parameters covered in the materials specification shall take precedence over those mentioned in these test...

ASTM D785-23 - Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials
March 15, 2023 - ASTM International

4.1 A Rockwell hardness number is a number derived from the net increase in depth impression as the load on an indenter is increased from a fixed minor load to a major load and then returned to a minor load (Procedure A). A Rockwell alpha (a) hardness number represents...

ASTM D256-23 - Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
March 15, 2023 - ASTM International

5.1 Before proceeding with these test methods, reference should be made to the specification of the material being tested. Any test specimen preparation, conditioning, dimensions, and testing parameters covered in the materials specification shall take precedence over those mentioned in these test...

ASTM D256-23e1 - Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
March 15, 2023 - ASTM International

5.1 Before proceeding with these test methods, reference should be made to the specification of the material being tested. Any test specimen preparation, conditioning, dimensions, and testing parameters covered in the materials specification shall take precedence over those mentioned in these test...

ASTM F1202-22 - Standard Specification for Washing Machines, Heat Sanitizing, Commercial, Pot, Pan, and Utensil Vertically Oscillating Arm Type
April 1, 2022 - ASTM International

1.1 This specification covers manually fed, motor-driven vertically oscillating arm type, automatically controlled, commercial pot, pan, and utensil washing machines, hereinafter referred to as "the washer." 1.2 The values stated in inch-pound units are to be regarded as standard. The values...

ASTM F1166-23 - Standard Practice for Human Engineering Design for Marine Systems, Equipment, and Facilities
January 1, 2023 - ASTM International

1.1 This practice provides ergonomic design criteria from a human-machine perspective for the design and construction of maritime vessels and structures and for equipment, systems, and subsystems contained therein, including vendor-purchased hardware and software. 1.1.1 The focus of these design...

ASTM F1166-22 - Standard Practice for Human Engineering Design for Marine Systems, Equipment, and Facilities
September 1, 2022 - ASTM International

1.1 This practice provides ergonomic design criteria from a human-machine perspective for the design and construction of maritime vessels and structures and for equipment, systems, and subsystems contained therein, including vendor-purchased hardware and software. 1.1.1 The focus of these design...

ASTM F1717-21 - Standard Test Methods for Spinal Implant Constructs in a Vertebrectomy Model
April 1, 2021 - ASTM International

5.1 Spinal implants are generally composed of several components which, when connected together, form a spinal implant assembly. Spinal implant assemblies are designed to provide some stability to the spine while arthrodesis takes place. These test methods outline standard materials and methods for...

DS/ISO 21593 - Ship and marine technology – Technical requirements for liquefied natural gas bunkering dry-disconnect/connect coupling
September 9, 2019 - DS

This International Standard specifies the design, minimum safety and functional requirements, inspection and testing procedures for LNG dry-disconnect/connect coupling served for LNG hose bunkering system intended for use on LNG bunker ship, tank truck and shore-based facility etc. This standard is...

ISO 16417 - Earth-moving machinery — Hydraulic breakers — Terminology and commercial specifications
November 1, 2020 - ISO

This document establishes the terminology and content of commercial specifications for hydraulic breakers which are mounted as an attachment on a carrier, typically earth-moving machinery such as an excavator, backhoe loader, skid steer loader, and compact loader as defined in...

ASTM D1998-21 - Standard Specification for Polyethylene Upright Storage Tanks
July 15, 2021 - ASTM International

1.1 This specification covers flat-bottom, upright, cylindrical tanks molded in one-piece seamless construction by rotational molding. The tanks are molded from polyethylene for above ground, vertical installation and are capable of containing aggressive chemicals at atmospheric pressure. Included...

Advertisement