loading
ASTM D7853-13(2026) - Standard Test Method for Hydraulic Pullout Resistance of a Geomembrane with Locking Extensions Embedded in Concrete
June 1, 2026 - ASTM International

1.1 This test method covers the determination of the hydraulic pullout resistance of a geomembrane with locking extensions embedded in concrete by determining the pressure required for locking extensions of the embedded specimen to pullout of the concrete. 1.2 The values stated in SI...

ASTM D5482-26 - Standard Test Method for Vapor Pressure of Petroleum Products and Liquid Fuels (Mini Method—Atmospheric)
May 1, 2026 - ASTM International

5.1 Vapor pressure is an important physical property of volatile liquids. 5.2 Vapor pressure is critically important for both automotive and aviation gasolines, affecting starting, warm-up, and tendency to vapor lock with high operating temperatures or high altitudes. Maximum vapor pressure...

ASTM D4953-26 - Standard Test Method for Vapor Pressure of Gasoline and Gasoline-Oxygenate Blends (Dry Method)
May 1, 2026 - ASTM International

5.1 Vapor pressure is an important physical property of liquid spark-ignition engine fuels. It provides an indication of how a fuel will perform under different operating conditions. For example, vapor pressure is a factor in determining whether a fuel will cause vapor lock at high ambient...

ASTM D323-26 - Standard Test Method for Vapor Pressure of Petroleum Products (Reid Method)
May 1, 2026 - ASTM International

5.1 Vapor pressure is an important physical property of volatile liquids. This test method is used to determine the vapor pressure at 37.8?°C (100?°F) of petroleum products and crude oils with initial boiling point above 0?°C (32?°F). 5.2 Vapor pressure is critically important for both automotive...

ASTM C964-20(2025) - Standard Guide for Lock-Strip Gasket Glazing
October 1, 2025 - ASTM International

1.1 This guide covers the use of lock-strip gaskets in compliance with Specification C542 in walls of buildings not over 15° from a vertical plane. The prime performance considerations are weathertightness against air and water infiltration, and structural integrity under wind loads....

ASTM F2317/F2317M-26 - Standard Specification for Design of Weight-Shift-Control Aircraft
May 1, 2026 - ASTM International

This specification covers the minimum requirement for designing, testing, and labeling of weight-shift-control aircraft. This specification covers only weight-shift-control aircraft in which flight control systems do not use hinged surfaces controlled by the pilot. Flight requirements are specified...

ASTM D2838-18(2026) - Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting
April 1, 2026 - ASTM International

5.1 As a result of the manufacturing process, internal stresses are locked into the film and these can be released by heating. Note 3: For any given type of film or sheeting, the temperatures at which shrinkage will begin are related to processing techniques employed to manufacture the film...

ASTM F1505-16(2026) - Standard Specification for Insulated and Insulating Hand Tools
March 1, 2026 - ASTM International

This specification covers the testing and corresponding design and performance requirements for insulated and insulating hand tools used for working on, or in close proximity to, energized electrical apparatus or conductors operating at maximum voltage of 1000 V ac or 1500 V dc. The hand tools...

ASTM C716-06(2025) - Standard Specification for Installing Lock-Strip Gaskets and Infill Glazing Materials
October 1, 2025 - ASTM International

This specification covers installation procedures for lock-strip gaskets and for infill glazing materials in lock-strip gasket glazing applications used in building walls. The prime performance considerations are weathertightness against air and water infiltration, and structural...

ASTM F2098-26 - Standard Specification for Stainless Steel Clamps for Securing SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) to Metal Insert and Plastic Insert Fittings
February 1, 2026 - ASTM International

This specification covers stainless steel clamps for securing SDR9 cross-linked polyethylene (PEX) tubing to metal insert and plastic insert fittings. All performance tests shall be performed on assemblies of fittings, clamps and PEX tubing. Clamps shall meet the material and dimensional...

ASTM D2732-14(2025) - Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film and Sheeting
December 1, 2025 - ASTM International

4.1 As a result of the manufacturing process, internal stresses may be locked into the film which can be released by heating. The temperature at which shrinkage will occur is related to the processing techniques employed to manufacture the film and may also be related to a phase transition...

ASTM F2009-25 - Standard Test Method for Determining the Axial Disassembly Force of Taper Connections of Modular Prostheses
September 15, 2025 - ASTM International

4.1 This test method helps to assess the axial locking force of a modular taper. Some types of devices that can utilize this type of connection are the modular shoulder and modular hip prostheses. Additional means of evaluating the locking mechanisms of tapers can be appropriate,...

ASTM F3781-25 - Standard Test Method for Measurement of the Fracture Resistance of a Modular Resilient Flooring's Profiled Edge(s) to an Applied Vertical Force
November 1, 2025 - ASTM International

4.1 Modular flooring having profiled edges, installed as a floating floor can provide a quick and easy installation system. The product is held together by the interlocking profiled edges. If the profiled edges are too brittle, over flexed, etc. they can be susceptible to fracture, which can then...

ASTM D7344-17a(2025) - Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure (Mini Method)
November 1, 2025 - ASTM International

5.1 The distillation (volatility) characteristics of hydrocarbons and other liquids have an important effect on their safety and performance, especially in the case of fuels and solvents. The boiling range gives information on the composition, the properties, and the behavior of the fuel during...

ASTM D3462/D3462M-25 - Standard Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules
November 1, 2025 - ASTM International

1.1 This specification covers asphalt roofing in shingle form, composed of glass felt or felts impregnated and coated on both sides with asphalt, and surfaced on the weather side with mineral granules. This specification is designed for the evaluation of products as manufactured. The test methods,...

ASTM F1577-05(2025) - Standard Test Methods for Detention Locks for Swinging Doors
June 1, 2025 - ASTM International

4.1 A major concern for detention and correctional administrative officials is the reliable operation of locks used in their facilities. These test methods aid in assigning a level of physical security and performance to locks for swinging door assemblies. 4.2 These test methods evaluate the...

ASTM F2098-25 - Standard Specification for Stainless Steel Clamps for Securing SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) to Metal Insert and Plastic Insert Fittings
August 1, 2025 - ASTM International

This specification covers stainless steel clamps for securing SDR9 cross-linked polyethylene (PEX) tubing to metal insert and plastic insert fittings. All performance tests shall be performed on assemblies of fittings, clamps and PEX tubing. Clamps shall meet the material and dimensional...

ASTM D5973-97(2025) - Standard Specification for Elastomeric Strip Seals with Steel Locking Edge Rails Used in Expansion Joint Sealing
May 1, 2025 - ASTM International

1.1 This specification covers the material requirements for preformed elastomeric strip seals and the corresponding steel locking edge rail used in expansion joint sealing. The scope of this specification is limited to preformed non-reinforced strip seals that mechanically lock into...

ASTM C542-05(2024) - Standard Specification for Lock-Strip Gaskets
November 1, 2024 - ASTM International

This specification defines the required properties of lock-strip gaskets where resistance to sunlight, weathering, flame, oxidation, permanent deformation under load, and diminution of gripping pressure are prime essentials. Gaskets shall be manufactured from an ozone-resistant compound and...

Advertisement