loading
ASTM MEMBRANE SWITCHES - ASTM STANDARDS RELATED TO MEMBRANE SWITCHES
ASTM
A description is not available for this item.
ASTM SWITCHES - ASTM STANDARDS RELATED TO MEMBRANE SWITCHES
ASTM
A description is not available for this item.
ASTM F2114 - Standard Guide for ASTM Standard Test Methods, Standard Practices, and Typical Values of a Membrane Switch
December 10, 2002 - ASTM

This guide contains a list of the current test methods and practices generated by Subcommittee F01.18 on Membrane Switches along with typical values for specifying certain performance characteristics of a membrane switch. As a minimum, for any particular membrane...

ASTM F2114-02 - Standard Guide for ASTM Standard Test Methods, Standard Practices, and Typical Values of a Membrane Switch (Withdrawn 2009)
December 10, 2002 - ASTM International

1.1 This guide contains a list of the current test methods and practices generated by Subcommittee F01.18 on Membrane Switches along with typical values for specifying certain performance characteristics of a membrane switch. 1.2 As a minimum, for any particular...

ASTM F1578-07(2014) - Standard Test Method for Contact Closure Cycling of a Membrane Switch (Withdrawn 2023)
June 1, 2014 - ASTM International

1.1 This test method covers the setup, procedure, and apparatus required to depress and release a membrane switch to a predetermined number of cycles. 1.2 This test method also covers the optional use of specified voltage and current during the cycling of the membrane...

ASTM F1578-07 - Standard Test Method for Contact Closure Cycling of a Membrane Switch
December 1, 2007 - ASTM International

1.1 This test method covers the setup, procedure, and apparatus required to depress and release a membrane switch to a predetermined number of cycles. 1.2 This test method also covers the optional use of specified voltage and current during the cycling of the membrane...

ASTM F2865-11 - Standard Guide for Classifying the Degrees of Ingression Protection Provided by a Membrane Switch
July 1, 2011 - ASTM International

1.1 This guide establishes a classification system and references test methods for verifying the degrees of protection provided by a membrane switch against the following: 1.1.1 The ingress of dust into a membrane switch. 1.1.2 Ingress of water into a membrane...

ASTM F1578 - Standard Test Method for Contact Closure Cycling of a Membrane Switch
December 1, 2007 - ASTM

1.1 This test method covers the setup, procedure, and apparatus required to depress and release a membrane switch to a predetermined number of cycles. 1.2 This test method also covers the optional use of specified voltage and current during the cycling of the membrane...

GMKOREA EDS-T-5217 - SIGNAL SWITCH
October 21, 2008 - GMKOREA

PURPOSE In these technical terms of delivery, the function-, bearing- and fatigue-tests for signal-and wiper-switches are determined. The switches are distinguished into two types separated from each other which are constructed as follows : Type A = Signal switch with...

MIL-DTL-12211 - SWITCH, PRESSURE
July 7, 2017 - NPFC

This specification covers two types of automotive pressure switches (see 6.1). Type I switches operate when fluid pressures drop below predetermined values and type II switches operate when fluid pressures exceed predetermined values.

GMKOREA EDS-T-5225 - ELECTRIC SWITCH
October 21, 2008 - GMKOREA

PURPOSE Purpose of this specification is to determine the function test and endurance test condition of switches to be installed in the car (pull-, rotary-, tumbler- and rocker type-switches) except the switches concentrated in the signal scanner: to here apply the tech....

J253_198912 - HEADLAMP SWITCH
December 1, 1989 - SAE International

This document defines the test conditions, procedures, and performance specifications for 6-, 12-, and 24-V manually actuated headlamp switches (circuit breaker(s) may be incorporated for circuit overload protection).

QPL-12211 - Switch, Pressure
February 11, 2021 - NPFC

QUALIFIED PRODUCT LIST OF PRODUCTS QUALIFIED UNDER PERFORMANCE SPECIFICATION MIL-DTL-12211 Switch, Pressure This list has been prepared for use by or for the Government in the acquisition of products covered by the subject specification and such listing of a product is not intended to and...

UL 1008 - Transfer Switch Equipment
July 13, 2022 - ULSE

1.1 This standard applies to the following types of transfer switches that have a maximum rating of 1000 volts for use in non-hazardous locations, in accordance with Annex A1, Item 1: a) Automatic transfer switches; b) Manual or non-automatic transfer switches; c) Closed...

J2456_199805 - Mercury Switch Removal Process
May 1, 1998 - SAE International

Mercury capsules have been used in the automotive industry in various switching applications. The basic design and performance characteristics of mercury switches (or capsules) make these components particularly suited to underhood light and trunk light applications. The processes...

J112_197710 - ELECTRIC WINDSHIELD WIPER SWITCH
October 1, 1977 - SAE International

This SAE Recommended Practice covers temperature test, endurance test setup, and endurance requirements for an electric windshield wiper switch. It also covers the combination windshield wiper and washer switch.

CSA C22.2 NO 178.1 - Transfer switch equipment
January 1, 2014 - CSA

This standard applies to the following types of transfer switches that have a maximum rating of 1000 volts for use in non-hazardous locations, in accordance with Annex A1, Item 1: a) Automatic transfer switches; b) Manual or non-automatic transfer switches; c) Closed transition...

J1167_202109 - Motorcycle Stop Lamp Switch
September 15, 2021 - SAE International

This SAE Standard defines the test conditions, procedures, and performance specifications for 6 V and 12 V stop lamp switches intended for use on motorcycles.

NR NB 170 - Clamp-Lock Switch Assemblies
March 8, 2019 - NR

The affected micro-switch assemblies can be found in MPSs, on pallets of equipment at manufacturers yards and in complete new and replacement lock body mechanisms or as replacement switch assemblies. Purpose This notice board highlights non-standard nuts fitted to Clamp-Lock...

J1076_199003 - BACKUP LAMP SWITCH
March 16, 1990 - SAE International

This standard defines the test conditions, procedures and performance specification for 6, 12, and 24 V backup lamp switches which are intended for use in motor vehicles.

Advertisement