loading
ANSI METRIC PKG - ANSI'S 7-VOLUME METRIC PACKAGE
ANSI
A description is not available for this item.
ASTM C1350M-25 - Standard Test Method for Measurement of Viscosity of Glass Between Softening Point and Annealing Range (Approximately 108 Pa·s to Approximately 1013 Pa·s) by Beam Bending (Metric)
July 1, 2025 - ASTM International

1.1 This test method covers the determination of glass viscosity from approximately 108?Pa·s to approximately 1013?Pa·s by measuring the rate of viscous bending of a simply loaded glass beam.2 Due to the thermal history of the glass, the viscosity may not represent conditions of thermal...

ASTM F606/F606M-26a - Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
May 15, 2026 - ASTM International

These test methods establishes the standard procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers and direct tension indicators, and rivets. For externally threaded fasteners, the mechanical tests describe the procedures for...

ASTM F606/F606M-26 - Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
May 1, 2026 - ASTM International

These test methods establishes the standard procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers and direct tension indicators, and rivets. For externally threaded fasteners, the mechanical tests describe the procedures for...

ASTM E2375-26a - Standard Practice for Ultrasonic Testing of Wrought Products
March 15, 2026 - ASTM International

1.1 Purpose-This practice covers the minimum requirements for ultrasonic examination of wrought products. Note 1: This practice was adopted to replace MIL-STD-2154, 30 Sept. 1982. This practice is intended to be used for the same applications as the document which it replaced. Users should...

ASTM E2375-26 - Standard Practice for Ultrasonic Testing of Wrought Products
January 1, 2026 - ASTM International

1.1 Purpose-This practice covers the minimum requirements for ultrasonic examination of wrought products. Note 1: This practice was adopted to replace MIL-STD-2154, 30 Sept. 1982. This practice is intended to be used for the same applications as the document which it replaced. Users should...

ASTM F606/F606M-25a - Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
November 13, 2025 - ASTM International

These test methods establishes the standard procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers and direct tension indicators, and rivets. For externally threaded fasteners, the mechanical tests describe the procedures for...

ASTM F2788/F2788M-25 - Standard Specification for Metric and Inch-sized Crosslinked Polyethylene (PEX) Pipe
August 1, 2025 - ASTM International

1.1 This specification covers crosslinked polyethylene (PEX) pipe that is outside diameter controlled in metric pipe sizes of DN 16 to DN 1000 (approximate outside diameters of 16 mm to 1005 mm) and inch pipe sizes NPS 3 to NPS 54 (approximate outside diameters of 3.5 in. to 54 in.), made in...

ASTM F606/F606M-25 - Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
May 1, 2025 - ASTM International

These test methods establishes the standard procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers and direct tension indicators, and rivets. For externally threaded fasteners, the mechanical tests describe the procedures for...

ASTM F436/F436M-24 - Standard Specification for Hardened Steel Washers Inch and Metric Dimensions
November 1, 2024 - ASTM International

1.1 This specification covers the chemical, mechanical, and dimensional requirements for hardened steel washers for use with fasteners having nominal thread diameters of 1/4 through 4 in. and M12 through M100. These washers are intended for general-purpose mechanical and structural use with bolts,...

Laser Beam Quality Metrics
January 1, 2013 - SPIE

Laser beam quality is more complicated and subtle than is usually assumed, a fact that has caused no end of frustration and misunderstanding between laser manufacturers, users, and acquirers. Laser Beam Quality Metrics guides the reader through the subtleties of laser...

ASTM C598-24 - Standard Test Method for Annealing Point and Strain Point of Glass by Beam Bending
August 1, 2024 - ASTM International

1.1 This test method covers the determination of the annealing point and the strain point of a glass by measuring the rate of midpoint viscous bending of a simply loaded glass beam.2 However, at temperatures corresponding to the annealing and strain points, the viscosity of glass is highly...

ASTM F2788/F2788M-24 - Standard Specification for Metric and Inch-sized Crosslinked Polyethylene (PEX) Pipe
September 1, 2024 - ASTM International

1.1 This specification covers crosslinked polyethylene (PEX) pipe that is outside diameter controlled in metric pipe sizes of DN 16 to DN 1000 (approximate outside diameters of 16 mm to 1005 mm) and inch pipe sizes NPS 3 to NPS 54 (approximate outside diameters of 3.5 in. to 54 in.), made in...

ASTM F606/F606M-24 - Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
November 1, 2024 - ASTM International

These test methods establishes the standard procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers and direct tension indicators, and rivets. For externally threaded fasteners, the mechanical tests describe the procedures for...

A-A-50503 - SCALE, BALANCE, BEAM INDICATING: METRIC, 2610 GRAM CAPACITY
April 30, 2019 - NPFC

This commercial item description (CID) establishes the government acquisition requirements for a 2610 gram capacity beam indicating balance scale.

MA2284 - FITTING, TEE, BEAM SEAL, METRIC
April 28, 2015 - SAE International
A description is not available for this item.
MA2303 - FITTING, UNION, BEAM SEAL, METRIC
April 28, 2015 - SAE International
A description is not available for this item.
ASTM D7726-11(2023) - Standard Guide for The Use of Various Turbidimeter Technologies for Measurement of Turbidity in Water
November 1, 2023 - ASTM International

5.1 Turbidity is a measure of scattered light that results from the interaction between a beam of light and particulate material in a liquid sample. Particulate material is typically undesirable in water from a health perspective and its removal is often required when the water is intended...

DS/EN 3275 - Aerospace series – Pipe coupling 8°30' up to 28 000 kPa Dynamic beam seal – Metric series – Technical specification
May 6, 2019 - DS

This European Standard specifies the required characteristics, inspection and test methods, quality assurance and procurement requirements for metric series 8°30' dynamic beam seal pipe couplings, for temperature ranges type II and III according to ISO 6771 and nominal pressure up to...

Advertisement