loading
ASTM E2964-26 - Standard Test Method for Measurement of the Normalized Insertion Loss of Doors
May 15, 2026 - ASTM International

5.1 This standard provides a method for testing the apparent sound insulating properties of doors in the field originally proposed by Morin (1). This allows doors to be evaluated with a result that has been found to be similar to the transmission loss. 5.2 The results of this measurement are the...

ASTM C1959/C1959M-26 - Standard Test Method for Non-Contact Measurement of Resonant Frequencies of Concrete Cylinders
March 1, 2026 - ASTM International

1.1 This is a test method for measuring resonant frequencies of a concrete cylinder by recording the airborne sound emitted by the cylinder after being struck by an impactor. The sound is recorded through the microphone of a smartphone or tablet computer. The recorded sound signal is...

ASTM E3492-25 - Standard Practice for Commonly Referenced Acoustical Calculation Procedures
October 1, 2025 - ASTM International

5.1 The general approach to adjusting measurements for the presence of background noise is to subtract the background noise from the average level measurement, leaving only the adjusted average level. The procedure is to make two otherwise identical measurements in any order, and then calculate the...

ASTM E1007-25 - Standard Test Method for Field Measurement of Tapping Machine Impact Sound Transmission Through Floor-Ceiling Assemblies and Associated Support Structures
August 1, 2025 - ASTM International

1.1 This test method covers the measurement of the transmission of impact sound generated by a standard tapping machine through floor-ceiling assemblies and associated supporting structures in field situations. 1.2 Results are measurable for all types of floor-ceiling assemblies, including those...

ASTM D6820-25 - Standard Guide for Use of the Time Domain Electromagnetic Method for Geophysical Subsurface Site Investigation
July 1, 2025 - ASTM International

5.1 Concepts: 5.1.1 All TDEM/TEM instruments are based on the concept that a time-varying magnetic field generated by a change in the current flowing in a large loop on the ground will cause current to flow in the earth below it (Fig. 3). In the typical TDEM/TEM system, these earth-induced currents...

ASTM E3091-17(2024) - Standard Specification for Systems to Measure Sound Levels
May 1, 2024 - ASTM International

This specification covers measurement systems used in making sound pressure level measurements in buildings in accordance with ASTM standards and guides. The measurement system includes all the components necessary to indicate measured sound pressure levels, such as microphones,...

ASTM E2611-24 - Standard Test Method for Normal Incidence Determination of Porous Material Acoustical Properties Based on the Transfer Matrix Method
May 1, 2024 - ASTM International

1.1 This test method covers the use of a tube, four microphones, and a digital frequency analysis system for the measurement of normal incident transmission loss and other important acoustic properties of materials by determination of the acoustic transfer matrix. 1.2 The values stated in SI...

ASTM E1050-24 - Standard Test Method for Impedance and Absorption of Acoustical Materials Using a Tube, Two Microphones and a Digital Frequency Analysis System
May 1, 2024 - ASTM International

1.1 This test method covers the use of an impedance tube, two microphone locations, and a digital frequency analysis system for the determination of normal incidence sound absorption coefficients and normal specific acoustic impedance ratios of materials. 1.2 Laboratory Accreditation-A...

ASTM C747-23 - Standard Test Method for Moduli of Elasticity and Fundamental Frequencies of Carbon and Graphite Materials by Sonic Resonance
October 1, 2023 - ASTM International

1.1 This test method covers determination of the dynamic elastic properties of isotropic and near isotropic carbon and graphite materials at ambient temperatures. Specimens of these materials possess specific mechanical resonant frequencies that are determined by the elastic modulus, mass, and...

ASTM E3397-23 - Standard Practice for Resonance Testing Using the Impulse Excitation Method
July 1, 2023 - ASTM International

4.1 IEM Applications and Capabilities-IEM has been successfully applied to a wide range of NDT applications in the manufacture, maintenance, and repair of metallic and non-metallic parts. Examples of anomalies detected are discussed in 1.1 and 6.2. IEM has been proven to provide fast,...

ASTM F2504-05(2022) - Standard Practice for Describing System Output of Implantable Middle Ear Hearing Devices
October 1, 2022 - ASTM International

5.1 IMEHDs are alternatives to air conduction hearing aids. They are similar to air conduction hearing aids in that they process incoming sound by applying frequency shaping and compression to create an analog, vibratory audio frequency output. IMEHDs differ from hearing aids in that they do not...

ASTM F1166-23 - Standard Practice for Human Engineering Design for Marine Systems, Equipment, and Facilities
January 1, 2023 - ASTM International

1.1 This practice provides ergonomic design criteria from a human-machine perspective for the design and construction of maritime vessels and structures and for equipment, systems, and subsystems contained therein, including vendor-purchased hardware and software. 1.1.1 The focus of these design...

J2521_202210 - Inertia Dynamometer Brake Squeal Noise Test Procedure for Vehicles without Regenerative Systems
October 7, 2022 - SAE International

The SAE J2521 procedure applies to high-frequency squeal noise occurrences for on-road passenger cars and light trucks below 4540 kg of GVWR. The procedure incorporates high-temperature and low-temperature test matrixes but does not fully account for the effects of the environment on brake squeal....

ASTM F1166-22 - Standard Practice for Human Engineering Design for Marine Systems, Equipment, and Facilities
September 1, 2022 - ASTM International

1.1 This practice provides ergonomic design criteria from a human-machine perspective for the design and construction of maritime vessels and structures and for equipment, systems, and subsystems contained therein, including vendor-purchased hardware and software. 1.1.1 The focus of these design...

ASTM E3353-22 - Standard Guide for In-Process Monitoring Using Optical and Thermal Methods for Laser Powder Bed Fusion
July 1, 2022 - ASTM International

4.1 Metal additive manufacturing has broadened design space, enabling production of more complex and customized products. Additive technology along with the broadened design space is pushing the limits of inspection capabilities and has led to challenges in process and product qualification,...

J1281_202204 - Operator Sound Pressure Level Exposure Measurement Procedure for Powered Recreational Craft
April 25, 2022 - SAE International

This SAE Standard establishes the procedure for determining the operator duty cycle sound pressure level L odc to which operators of powered recreational craft up to 24 m in length are exposed during typical operation as determined by marine engine duty cycle studies. This document describes the...

MIL-PRF-87819 - HEADSET-MICROPHONE, (HEARING PROTECTIVE TYPE, HIGH AND MODERATE AMBIENT NOISE LEVELS), GENERAL SPECIFICATION FOR
December 21, 2020 - NPFC

Scope. This specification covers the requirements for headset-microphones with rigid headband. These parts meet established requirements for communications equipment used to protect against hazardous noise exposure and are approved for use in certain high and moderate ambient noise level...

MIL-DTL-55535 - HEADSET-MICROPHONE KIT MK-1039/G
March 17, 2020 - NPFC

Scope. This specification covers Headset-Microphone Kit MK-1039/G. This Headset-Microphone Kit is designed to fit both the regular and large size Combat Vehicle Crewman's Helmet. The electrical characteristics of the kit are compatible with Tactical Radio Systems, such as the VRC-12....

ASTM E2964-21 - Standard Test Method for Measurement of the Normalized Insertion Loss of Doors
August 1, 2021 - ASTM International

5.1 This standard provides a method for testing the apparent sound insulating properties of doors in the field originally proposed by Morin (1).6 This allows doors to be evaluated with a result that has been found to be similar to the transmission loss. 5.2 The results of this measurement are the...

ITU-T P.382 - Technical requirements and test methods for multi-microphone wired headset or headphone interfaces of digital wireless terminals
October 1, 2020 - ITU-T

This Recommendation specifies electrical requirements and test methods for a multi-microphone headset or headphone (HP) interface used in digital mobile terminals. It is also applicable to terminals with a digital headset interface combined with an external adapter for an analogue...

Advertisement