4.1 This test method enumerates yeast and mold. Yeast and mold have been known to cause damage to hides and skins.
4.1 This test method provides a technique for evaluating mold growth resistance characteristics of Wet Blue and Wet White, and should assist in the prediction of storage time before molding occurs. 4.2 The degree of correlation between this test and commercial quantities of Wet Blue and Wet...
4.1 This test method enumerates salt tolerant yeast and mold, and under the conditions of this test method those are equated as halophilic organisms. Salt tolerant yeast and mold have been known to cause damage to hides and skins in raceway brine.
6.1 The environmental chamber method is an accelerated test for determining the resistance of Wet Blue and Wet White to the growth of fungi, the causal agent of mold. See Test Method D3273., 6.2 The environmental chamber method is useful in estimating the performance of fungicides and should...
1.1 This specification covers the requirements and test methods for the material, dimensions, workmanship, and the properties of extruded sheet, rod and tubular bar manufactured from unfilled PVDF. 1.2 This specification covers the requirements and test methods for the material, dimensions,...
This specification covers melt-processible molding and extrusion materials of FEP-fluorocarbon resin, which is a copolymer of tetrafluoroethylene and hexafluoropropylene or a modified FEP-fluorocarbon resin containing not more than 2% by weight of other fluoromonomers. Four types of...
This specification covers melt processable unmodified poly(vinylidene fluoride) (PVDF) molding, extrusion and coating materials. This specification covers only virgin homopolymer prepared from vinylidene fluoride supplied in form of pellet or powder and shall be free of foreign matter. Two types...
1.1 This test method is used to determine the resistance of plastics to breakage by flexural shock as indicated by the energy extracted from standardized (see Note 1) pendulum-type hammers, mounted in standardized machines, in breaking standard specimens with one pendulum swing. This test method...
1.1 These test methods may be used to determine the water content of soils and the dry density of soils in place using Time Domain Reflectometry. 1.2 These test methods apply to soils that have 30?% or less by weight of their particles retained on the 19.0-mm [3/4-in.] sieve. 1.3 These test methods...
4.1 Defacement of paint and coating films by fungal growth (mold, mildew) is a common phenomenon, and defacement by algal growth as referenced in Test Method D5589 can also occur under certain conditions. It is generally known that differences in the environment, lighting, temperature,...
This specification covers aluminum-alloy permanent mold castings. The responsibility of furnishing castings that can be laid out and machined to the finished dimensions within the permissible variations specified shall rest with the producer, except where mold equipment is furnished...
5.1 SGCs are used to produce asphalt mixture specimens in the laboratory to assess volumetric properties and predict pavement performance. In the fabrication of an SGC specimen in accordance with Test Method D6925, loose asphalt mixture is placed inside a metal mold, which is then placed...
5.1 During preconstruction and construction evaluations, use of these test methods establishes specific and overall performance characteristics for the mortar system. 5.2 Preconstruction testing of mortars prebatched by weight provides information for the selection of the individual mortar system...
1.1 This test method is intended to differentiate, in a preliminary fashion, among materials with respect to their resistance to ignition because of their proximity to electrically-heated wires and other heat sources. 1.2 This test method applies to molded or sheet materials available in...
1.1 This test method covers the determination of total carbon in mold powders in the concentration range from 1?% to 25?%. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This test method has been evaluated in...
5.1 During the normal course of play, it is foreseeable that impacts between the athlete and walls or other fixed objects will occur. Such impacts pose a potential threat of injury to the athlete. Padding is one product used to "protect" and reduce the likelihood of both head and other physical...
1.1 This specification covers commercial zinc alloys in ingot form for remelting for the manufacture of dies and molds from the alloys as shown in Table 1. 1.2 This specification presents requirements for zinc alloys suitable for the production of sand cast or plaster cast forming dies for...
3.1 In accordance with Specification D2227, shipments of TSR10 and TSR20 must meet a minimum initial Wallace plasticity (Po) of 30 to be accepted. However, even with this minimum restriction, the uncured viscoelastic or "processability" properties are allowed to vary greatly. This variation in...
1.1 This specification covers requirements and test methods for materials, workmanship, dimensions, perforations, pipe stiffness, elongation, joint separation resistance, quality of extruded polyethylene, brittleness, bond, and marking of corrugated polyethylene (PE) pipe and fittings. It covers...
Narrow Your Results