This comprehensive review of calibration provides an excellent foundation for understanding principles and applications of the most frequently performed tasks of a technician. Topics addressed include terminology, bench vs. field calibration, loop vs. individual instrument...
4.1 Standards such as ISO 11137-1 for radiation sterilization of healthcare products and ISO 14470 for irradiation of food state that dosimetry used in the process's development, validation, and routine control adhere to specific requirements. These requirements state that the dosimetry must be...
1.1 This test method covers the determination of the annealing point and the strain point of a glass by measuring the viscous elongation rate of a fiber of the glass under prescribed condition. 1.2 The annealing and strain points shall be obtained by following the specified procedure after...
5.1 The methods described represent the preferable means for calibration of field radiometers employing standard reference radiometers. Other methods involve the employment of an optical bench and essentially a point source of artificial light. While these methods are useful for cosine and...
1.1 This test method covers the procedure for the measurement of the Superpave Gyratory Compactor (SGC) internal angle of gyration using an instrument capable of simulating loading conditions similar to those created by an asphalt mixture specimen. 1.2 Units-The values stated in SI units are to be...
1.1 This test method covers the determination of the abrasion resistance of vulcanized (thermoset) rubbers, thermoplastic elastomers, and elastomeric and similar materials to a standardized reference system. A standardized set of reference compounds is used to calculate relative abrasion resistance...
1.1 This test method, commonly referred to as the Cummins ISB Viscosity Test, covers the utilization of a 5.9?L diesel engine equipped with exhaust gas recirculation and is used to evaluate oil performance with regard to soot induced viscosity increase. 1.2 The values stated in SI units are to be...
5.1 Need for Heat Flux Measurements: 5.1.1 Independent measurements of temperature and heat flux support the development and validation of engineering models of fires and other high environments, such as furnaces. For tests of fire protection materials and structural assemblies, temperature and...
1.1 This test method, commonly referred to as the Cummins ISB Test, covers the utilization of a modern, 5.9?L, diesel engine equipped with exhaust gas recirculation and is used to evaluate oil performance with regard to valve-train wear. 1.2 The values stated in SI units are to be regarded as...
1.1 This test method describes procedures for determining the mass concentration of particulate matter in gaseous streams using an automated, in-stack test procedure. This test method, which employs an in-situ, inertial microbalance, is based on inertial mass measurement using a hollow tube...
1.1 This guide describes the relationship of indoor carbon dioxide (CO2) concentrations to indoor air quality (IAQ) and building ventilation. 1.2 This guide contains background information on the health, comfort, and performance impacts of indoor CO2 exposure, as well as indoor CO2 limits contained...
1.1 This test method is commonly referred to as the Sequence VH test, and it has been correlated with the Sequence VG test. The Sequence VG test was previously correlated with vehicles used in stop-and-go service prior to 1996, particularly with regard to sludge and varnish formation.3 It is one of...
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a...
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856?kg or less. The tests are conducted using a specified spark-ignition engine with a...
1.1 This test method, commonly referred to as the Cummins ISB Viscosity Test, covers the utilization of a 5.9?L diesel engine equipped with exhaust gas recirculation and is used to evaluate oil performance with regard to soot induced viscosity increase. 1.2 The values stated in SI units are to be...
1.1 This test method, commonly referred to as the Cummins ISB Test, covers the utilization of a modern, 5.9?L, diesel engine equipped with exhaust gas recirculation and is used to evaluate oil performance with regard to valve-train wear. 1.2 The values stated in SI units are to be regarded as...
Narrow Your Results