1.1 These test methods determine the time of setting of hydraulic cement by means of the Vicat needle. Two test methods are given; Test Method A is the Reference Test Method using the manually operated standard Vicat apparatus, while Test Method B permits the use of an automatic Vicat...
4.1 This guide is designed to assist medical device manufacturers as they develop new devices or qualify existing devices (e.g., catheters, needles) for delivering clinical cell therapies (ISO 23033). Cytocompatibility considers the impact of the delivery device on the cells passing through...
1.1 These test methods cover procedures for mixing and testing alkali-activated cementitious material (AACM). 1.2 These test methods and procedures appear in the following order: Sections Mechanical Mixing of Pastes and Mortars of Plastic Consistency 4 - 10 Time of Setting of Pastes by Vicat...
1.1 This test method covers the evaluation and comparison of the resistance of solid organic dielectric materials to the initiation or growth, or both, of tubular tree-like channels resulting from partial discharge (corona) and molecular decomposition that occur in the region of very high,...
4.1 This guide is designed to assist medical device manufacturers as they develop new devices or qualify existing devices (e.g., catheters, needles) for delivering clinical cell therapies (ISO 23033). Cytocompatibility considers the impact of the delivery device on the cells passing through...
1.1 This test method covers the empirical estimation of the consistency of waxes derived from petroleum by measurement of the extent of penetration of a standard needle. This test method is applicable to waxes having a penetration of not greater than 250. Note 1: This test method is similar...
This specification covers the requirements for standard-type needle roller bearings with drawn outer rings, full complement, without inner rings, and with either open (Type B) or closed ends (Type M). Materials covered by this specification are needle rollers which shall be...
1.1 This test method is used to determine the force required to cause a sharp-edged hypodermic needle to penetrate through protective clothing material. The standard describes three needles that may be used: 21, 25, or 28 gauge needles. 1.2 The values stated in SI units are to...
This specification covers three types of masonry cement for use where mortar for masonry is required. Masonry cement shall conform to the applicable physical property requirements prescribed. The masonry cement shall be sampled in accordance with practice C 183. The temperature and relative...
1.1 This specification covers inner rings for needle roller bearings with drawn outer rings. 1.2 The inner rings specified in this specification are intended for use on unhardened shafts in conjunction with open end needle roller bearings shown on Specification F2162 and MS52141. 1.3...
1.1 This specification covers austenitic, stainless steel, needle tubing in hard-drawn tempers for industrial applications. 1.2 In general, needle tubing describes small-diameter tubing with outside diameters (ODs) in the range of 0.008 to 0.203 in. (0.2 to 5.2 mm) with nominal wall...
This specification covers glass fiber unsupported needled felt binder-free thermal insulations. This material is used as the thermal insulation component in the fabrication of insulation systems for use on machinery and equipment, such as steam turbines, boilers, boiler feed pumps, and...
1.1 These test methods cover three approaches for determining yield stress values of paints, inks and related liquid materials using rotational viscometers. The first method uses a rotational viscometer with coaxial cylinder, cone/plate, or plate/plate geometry. The second method uses a rheometer...
1.1 This test method covers the evaluation of the flammability of textile fabrics as they reach the consumer for apparel. This test method sets forth a classification system for apparel textiles and identifies textiles which have burning characteristics that make them unsuitable for use in...
1.1 This test method covers determination of the temperature at which a specified needle penetration occurs when specimens are subjected to specified controlled test conditions. 1.2 This test method is not recommended for ethyl cellulose, nonrigid poly(vinyl chloride), poly(vinylidene...
1.1 This test method covers the empirical estimation of the consistency of waxes derived from petroleum by measurement of the extent of penetration of a standard needle. This test method is applicable to waxes having a penetration of not greater than 250. Note 1: This test method is similar...
This guide is intended to provide a better understanding of the care of stainless steel surgical instruments intended for reuse. This guide is not intended for use with electrical, pneumatic, or other powered surgical instruments. The stainless steels most used are martensitic and austenitic types....
1.1 This test method covers the determination of total nitrogen (TN) and total dissolved nitrogen (TDN) in surface water, seawater, groundwater, wastewater, and wastewater effluents in the range from 0.2?mg/L N to 10?mg/L N. Concentrations from 10?mg/L to 500?mg/L are possible when used in...
1.1 This test method covers the determination of the trace total nitrogen naturally found in liquid hydrocarbons boiling in the range from approximately 50?°C to 400?°C, with viscosities between approximately 0.2?cSt and 10?cSt (mm2/s) at room temperature. This test method is applicable to...
1.1 This test method covers the empirical estimation of the consistency of waxes derived from petroleum by measurement of the extent of penetration of a standard needle. This test method is applicable to waxes having a penetration of not greater than 250. Note 1: This test method is similar...
Narrow Your Results