1.1 This specification covers technically important, commercially available, magnetically hard sintered ferrite permanent magnets. 1.2 Ferrite permanent magnets have residual induction Br from 0.2 T (2000 G) up to about 0.5 T (5000 G) and intrinsic coercive field...
The purpose of this Standard is to define the method of measurement of the magnetic flux density, magnetic polarization and the magnetic field strength and also to determine the demagnetization curve and recoil line of permanent magnet materials, the properties of which are presumed...
1.1 This specification covers technically important, commercially available, magnetically hard, cast and sintered permanent magnets known commonly as Alnico. 1.2 Alnico magnets have approximate magnetic properties of residual magnetic induction, Br, from 0.52 T (5200 G) to 1.35...
This specification covers one type of loudspeaker, designated loudspeaker, permanent magnet, LS-211/AIC-13. This loudspeaker is a horn type unit with a frequency response of 200-7,000 Hz, nominal 16 ohms voice coil impedance, and a 20 watt peak power output (see 6.1).
1.1 This test method covers the equipment, procedures, and measurement of the resistance of permanent magnet alloys against corrosion in high temperature, high pressure water vapor environments. This test is also known as the Bulk Corrosion Test (BCT). 1.2 The values and equations...
1.1 This specification covers technically important, commercially available, magnetically hard sintered and fully dense neodymium iron boron (Nd2Fe14B, NdFeB, or "Neo") permanent magnets. These materials are available in a wide range of compositions with a commensurately large range...
This specification covers permanent magnet loudspeakers, with enclosure, for use in 70-volt and 95-volt distribution systems on Naval ships as components of shipboard announcing systems.
1.1 This specification covers technically important, commercially available, magnetically hard sintered ferrite permanent magnets. 1.2 Ferrite permanent magnets have residual induction Br from 0.2 T (2000 G) up to about 0.5 T (5000 G) and intrinsic coercive field...
This specification covers technically important, commercially available, magnetically hard sintered ferrite permanent magnets Ferrite permanent magnets have residual induction Br from 0.2 T (2000 G) up to about 0.5 T (5000 G) and intrinsic coercive field strength HcJ...
This specification applies to technically important, commercially available, magnetically hard sintered (fully dense) permanent magnets commonly known as samarium cobalt (SmCo). SmCo permanent magnets are available in two general composition families abbreviated "SmCo...
Scope. This specification covers the general requirements for 2-watt, 4-inch diameter, permanent magnet loudspeakers encased in metal cabinets. These loudspeakers are fungus-, gunblast-, and immersion-resistant.
This specification covers technically important, commercially available, magnetically hard sintered (fully dense) permanent magnets commonly known as samarium cobalt. These materials are available in two general composition families abbreviated "SmCo 1:5" and "SmCo 2:17." The numbers...
Work Instruction for the calibration of electromagnets and permanent magnets for materials testing. To be used in the absence of a manufacturers calibration instruction.
This specification applies to technically important, commercially available, magnetically hard sintered (fully dense) permanent magnets commonly known as samarium cobalt (SmCo). SmCo permanent magnets are available in two general composition families abbreviated 'SmCo...
4.1 This test method is suitable for magnet specification, acceptance, service evaluation, quality control in magnet production, research and development, and design. 4.2 When a test specimen is cut or fabricated from a larger magnet, the magnetic properties measured on it are...
This specification covers technically important, commercially available, magnetically hard, cast and sintered permanent magnets known commonly as Alnico. Alnico magnets have approximate magnetic properties of residual magnetic induction, Br, from 0.52 T (5200 G) to 1.35 T...
1.1 This specification covers technically important, commercially available, magnetically hard, cast and sintered permanent magnets known commonly as Alnico. 1.2 Alnico magnets have approximate magnetic properties of residual magnetic induction, Br, from 0.52 T (5200 G) to 1.35...
1.1 This specification covers technically important, commercially available, magnetically hard sintered ceramic ferrite permanent magnets. 1.2 Ceramic ferrite magnets have residual magnetic induction Br from 2000 G (0.2 T) up to about 5000 G (0.5 T) and intrinsic coercive field...
Narrow Your Results