loading
PCMCIA PLUG AND PLAY - PCMCIA PLUG AND PLAY SYSTEM ARCHITECTURE
PCMCIA
A description is not available for this item.
ASTM E911-98(2026) - Standard Specification for Glass Stopcocks with Polytetrafluoroethylene (PTFE) Plugs
June 1, 2026 - ASTM International

This specification covers dimensional interchangeability requirements of glass stopcocks with polytetrafluoroethylene (PTFE) plugs for use in ordinary laboratory and industrial applications. However, it does not cover the design characteristics of the stopcock-plug assembly nor the...

ASTM E1046-85(2026) - Standard Specification for Glass Westergren Tube, Disposable
June 1, 2026 - ASTM International

This specification covers a disposable glass Westergren tube used for measuring the erythrocyte sedimentation rate. Covered by this specification are Type I (standard Westergren tube used in conventional racks only) and Type II (self-zeroing tubes used with racks that have convenient disposable...

ASTM D6794-26 - Standard Test Method for Measuring the Effect on Filterability of Engine Oils After Treatment with Various Amounts of Water and a Long (6?h) Heating Time
June 1, 2026 - ASTM International

1.1 This test method covers the determination of the tendency of an oil to form a precipitate that can plug an oil filter. It simulates a problem that may be encountered in a new engine run for a short period of time, followed by a long period of storage with some water in the oil. 1.2 The...

ASTM D6795-26 - Standard Test Method for Measuring the Effect on Filterability of Engine Oils After Treatment with Water and Dry Ice and a Short (30?min) Heating Time
June 1, 2026 - ASTM International

1.1 This test method covers the determination of the tendency of an oil to form a precipitate that can plug an oil filter. It simulates a problem that may be encountered in a new engine run for a short period of time, followed by a long period of storage with some water in the oil. 1.2 The...

ASTM D4520-18(2026) - Standard Practice for Determining Water Injectivity Through the Use of On-Site Floods
May 1, 2026 - ASTM International

5.1 The injectivity of a water is best determined by measurements as near to the well as possible to minimize changes in water properties due to air contact and time. This practice describes how core flow tests are carried out near the well. 5.2 This practice permits the differentiation of...

ASTM D7319-26 - Standard Test Method for Determination of Existent and Potential Sulfate and Inorganic Chloride in Fuel Ethanol and Butanol by Direct Injection Suppressed Ion Chromatography
March 1, 2026 - ASTM International

5.1 Sulfates and chlorides can be found in filter plugging deposits and fuel injector deposits. The acceptability for use of the fuel components and the finished fuels depends on the sulfate and chloride content. 5.2 Existent and potential inorganic sulfate and total chloride content, as...

ASTM A74-26 - Standard Specification for Cast Iron Soil Pipe and Fittings
April 1, 2026 - ASTM International

1.1 This specification covers cast iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. It establishes standards covering material, manufacture, mechanical and chemical properties, coating, test methods, inspection,...

ASTM D7155-20(2026) - Standard Practice for Evaluating Compatibility of Mixtures of Turbine Lubricating Oils
March 1, 2026 - ASTM International

5.1 The compatibility of oils can be important for users of oil-lubricated equipment. Mixing of two oils can produce a substance markedly inferior to either of its constituent materials. One or more of the following can occur: 5.1.1 A mixture of incompatible oils most often forms a precipitate. The...

ASTM D7752-26 - Standard Practice for Evaluating Compatibility of Mixtures of Hydraulic Fluids
March 1, 2026 - ASTM International

5.1 Hydraulic fluid compatibility is important to hydraulic equipment users because a mixture of incompatible fluids may produce a substance that is markedly inferior to its constituents. Even in identical base stocks, the formation of a precipitate may occur as a result of additive interactions....

ASTM D7522/D7522M-26 - Standard Test Method for Pull-Off Strength for FRP Laminate Systems Bonded to Concrete or Masonry Substrates
March 15, 2026 - ASTM International

1.1 This test method describes the apparatus and procedure for evaluating the pull-off strength of wet lay-up or pultruded (shop-fabricated) Fiber Reinforced Polymer (FRP) laminate systems adhesively bonded to a flat concrete substrate. The test determines the greatest perpendicular force (in...

ASTM B885-09(2026) - Standard Test Method for Presence of Foreign Matter on Printed Wiring Board Contacts
February 1, 2026 - ASTM International

5.1 This test method provides a way to detect contamination on printed wiring board fingers that affects the electrical performance of such fingers. Such contamination may arise during PWB manufacture, circuit assembly, or service life and may include solder mask, solder flux, hardened lubricants,...

ASTM F1550-26 - Standard Test Method for Determination of Fire-Test-Response Characteristics of Components or Composites of Mattresses or Furniture for Use in Correctional Facilities after Exposure to Vandalism, by Employing a Bench Scale Oxygen Consumption Calorimeter
January 1, 2026 - ASTM International

5.1 This test method provides a means to determine various fire-test-response characteristics, including the time to sustained flaming and the heat release rate, of composites exposed to a prescribed initial test heat flux in the cone calorimeter apparatus, after they have been vandalized in a...

ASTM D7591-25 - Standard Test Method for Determination of Free and Total Glycerin in Biodiesel Blends by Anion Exchange Chromatography
October 1, 2025 - ASTM International

5.1 Petroleum-based diesel may be blended with biodiesel. High levels of free glycerin in biodiesel can cause injector deposits ("gel effect"), as well as clogging fuel systems. High levels of unreacted glycerides can cause injector deposits and can adversely affect cold weather operation and...

ASTM D4570-02(2025) - Standard Test Method for Rubber Chemicals—Determination of Particle Size of Sulfur by Sieving (Dry)
November 1, 2025 - ASTM International

1.1 This test method covers the particle size measurement of the coarse fraction of ground sulfurs. It is limited to measurement of particles greater than 45 μm (No. 325 sieve). If the sulfur is very fine and the screens become plugged by the caking of the sulfur, it may be necessary to use...

ASTM F3287-17(2025) - Standard Test Method for Nondestructive Detection of Leaks in Packages by Mass Extraction Method
October 1, 2025 - ASTM International

5.1 Leaks in medical, pharmaceutical, or food product packages can affect product quality and consumer safety. Such leaks can arise from imperfections in package material or between mated components designed to seal the package. Defects can allow unwanted gas (for example, oxygen or water vapor),...

ASTM B62-17(2025) - Standard Specification for Composition Bronze or Ounce Metal Castings
October 1, 2025 - ASTM International

This specification establishes requirements for an alloy having a composition of copper, tin, lead, and zinc which is used for component castings of valves, flanges, and fittings. The specimen shall have the chemical composition of major elements: copper, tin, lead zinc, nickel including cobalt. It...

ASTM D6297-25 - Standard Specification for Asphaltic Plug Joints for Bridges
June 1, 2025 - ASTM International

1.1 This specification covers the material, testing, and application requirements for a field-molded asphaltic plug joint (APJ) used in expansion joint sealing on asphalt concrete overlay and portland cement concrete decks. The scope of this specification is limited to field-molded APJ. This...

ASTM F2030-21(2025) - Standard Specification for Paintball Cylinder Burst Disk Assemblies
September 1, 2025 - ASTM International

This specification covers cylinder burst disk assemblies for paintball marker propellant sources their application and installation requirements. The materials and processes used to manufacture the burst disk assembly shall result in items with mechanical strength sufficient to pass the applicable...

ASTM D6304-25 - Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fischer Titration
July 1, 2025 - ASTM International

5.1 A knowledge of the water content is important in the manufacturing, purchase, sale, or transfer of petroleum products to help in predicting their quality and performance characteristics. 5.2 The presence of moisture could lead to premature corrosion and wear, an increase in the debris load...

Advertisement