loading
ASTM F877-26 - Standard Specification for Crosslinked Polyethylene (PEX) Hot- and Cold-Water Distribution Systems
August 1, 2026 - ASTM International

This specification covers requirements, test methods, and methods of marking for crosslinked polyethylene plastic hot- and cold-water distribution systems components made in one standard dimension ratio. Components are comprised of tubing and fittings intended for use in residential and...

ASTM D2737-26 - Standard Specification for Polyethylene (PE) Plastic Tubing
April 1, 2026 - ASTM International

This specification covers polyethylene (PE) tubing pressure-rated for water. Included here are criteria for classifying PE plastic tubing materials and PE plastic tubing, and requirements and test methods for materials, workmanship, dimensions, bond strength, carbon black, density,.sustained...

ASTM F667/F667M-26 - Standard Specification for 3 through 24 in. Corrugated Polyethylene Pipe and Fittings
April 1, 2026 - ASTM International

1.1 This specification covers requirements and test methods for materials, workmanship, dimensions, perforations, pipe stiffness, elongation, joint separation resistance, quality of extruded polyethylene, brittleness, bond, and marking of corrugated polyethylene (PE) pipe and fittings...

ASTM E2425-21(2026) - Standard Test Method for Loss Modulus Conformance of Dynamic Mechanical Analyzers
July 1, 2026 - ASTM International

1.1 This test method describes the performance confirmation or measurement of conformance for the loss modulus scale of a commercial or custom-built dynamic mechanical analyzer (DMA) at 21 °C using ultra-high molecular weight polyethylene as a reference material. 1.2 The values stated in SI...

ASTM D6645-18(2026) - Standard Test Method for Methyl (Comonomer) Content in Polyethylene by Infrared Spectrophotometry
April 1, 2026 - ASTM International

1.1 This test method covers the determination of methyl groups (that is, comonomer content) in polyethylenes by infrared spectrophotometry. The test method is applicable to copolymers of ethylene with 1-butene, 1-hexene, or 1-octene having densities above 900 kg/m3. High-pressure low-density...

ASTM F1041-26 - Standard Guide for Squeeze-Off of Polyethylene Gas Pressure Pipe and Tubing
April 1, 2026 - ASTM International

1.1 This guide describes general procedures for squeeze-off of polyethylene gas pressure pipe and tubing as recommended in GRI-92/0147.1, GRI-92/0147.2, and OTD Project 2.14c / GTI Project 22245. Note 1: Operator squeeze-off procedures should be developed and qualified in accordance with...

ASTM D2513-26a - Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
April 1, 2026 - ASTM International

1.1 This specification covers requirements and test methods for material dimensions and tolerances, hydrostatic burst strength, chemical resistance, and rapid crack resistance of polyethylene pipe, tubing, and fittings for use in fuel gas pipelines for direct burial and reliner applications....

ASTM F876-26 - Standard Specification for Crosslinked Polyethylene (PEX) Tubing
February 1, 2026 - ASTM International

This specification covers crosslinked polyethylene (PEX) tubing that is outside diameter controlled, made in standard thermoplastic tubing dimension ratios, and pressure rated for water at three temperatures. This specification covers one PEX tubing material in one standard dimension ratio...

ASTM F3378/F3378M-26 - Standard Specification for Crosslinkable Polyethylene (CX-PE) Pipe
April 1, 2026 - ASTM International

1.1 This specification covers outside diameter controlled crosslinkable polyethylene (CX-PE) pipe produced in sizes DN 25 to 630 and NPS 1 to 24 in various dimension ratios. Included in this specification are requirements and test methods for the determination of the long-term hydrostatic...

ASTM F1281-26 - Standard Specification for Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Pressure Pipe
February 1, 2026 - ASTM International

1.1 This specification covers a coextruded crosslinked polyethylene composite pressure pipe with a welded aluminum tube reinforcement between the inner and outer layers. The inner and outer crosslinked polyethylene layers are bonded to the aluminum tube by a melt adhesive. Included is...

ASTM D1000-26 - Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications
June 1, 2026 - ASTM International

1.1 These test methods cover procedures for testing pressure-sensitive adhesive-coated tapes to be used as electrical insulation. These tapes are classified as follows: 1.1.1 Class 1-Non-elastomeric backings made from materials such as: Paper, flat or creped, Fabric, uncoated or coated, Cellulose...

ASTM F2164-26 - Standard Practice for Field Leak Testing of Polyethylene (PE) and Crosslinked Polyethylene (PEX) Pressure Piping Systems Using Hydrostatic Pressure
February 1, 2026 - ASTM International

1.1 This practice provides information on apparatus, safety, pre-test preparation, and procedures for conducting field tests of polyethylene and crosslinked polyethylene pressure piping systems by filling with a liquid and applying pressure to determine if leaks exist in the system. 1...

ASTM D2683-26 - Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing
February 1, 2026 - ASTM International

This specification covers polyethylene socket-type fittings for use with outside diameter-controlled polyethylene pipe and tubing. Fittings covered by this specification are normally molded. In-line fittings such as couplings, unions, bushings, caps, nipples, etc., may be extruded or...

ASTM D8646-26 - Standard Test Method for Calculating and Reporting the Estimated Biodegradation Time of Non-Persistent Plastics Designed for Use in Aquatic Environments
May 15, 2026 - ASTM International

1.1 This test method applies to non-floating biodegradable plastics intended for use in aerobic aquatic environments, specifically in marine, brackish, or fresh water ecosystems. The plastics covered under this test method are designed to not persist in the environment by converting into carbon...

ASTM D8265-26 - Standard Practices for Electrical Methods for Mapping Leaks in Installed Geomembranes
April 1, 2026 - ASTM International

1.1 These practices describe standard procedures for using electrical methods to locate leaks in geomembranes covered with liquid or earthen materials, or both. 1.2 These practices are intended to ensure that leak location surveys are performed to the highest technical capability of electrical...

ASTM F2818-26 - Standard Specification for Specification for Crosslinked Polyethylene (PEX) Material Gas Pressure Pipe and Tubing
April 1, 2026 - ASTM International

1.1 This specification covers requirements and test methods for material dimensions and tolerances, hydrostatic burst strength, chemical resistance, and impact resistance of PEX pipe and tubing for use in fuel gas mains and services for direct burial applications. 1.2 The text of this specification...

ASTM D3350-25 - Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
December 1, 2025 - ASTM International

1.1 This specification covers the initial identification of polyethylene (PE) compound pipe and fittings materials in accordance with a cell classification system. It is not the function of this specification to provide specific engineering data for design purposes, to specify manufacturing...

ASTM F3373-26 - Standard Specification for Polyethylene (PE) Electrofusion Fittings for Outside Diameter Controlled Crosslinked Polyethylene (PEX) Pipe or Tubing
February 1, 2026 - ASTM International

1.1 This specification covers polyethylene (PE 4710) electrofusion fittings for use with outside diameter-controlled crosslinked polyethylene (PEX) pipe and tubing, covered by Specifications F876, F2788/F2788M, F2905/F2905M and F2968/F2968M. As stated in these PEX standards, the PEX...

ASTM D2513-26 - Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
January 1, 2026 - ASTM International

1.1 This specification covers requirements and test methods for material dimensions and tolerances, hydrostatic burst strength, chemical resistance, and rapid crack resistance of polyethylene pipe, tubing, and fittings for use in fuel gas pipelines for direct burial and reliner applications....

ASTM C910-16(2026) - Standard Test Method for Bond and Cohesion of One-Part Elastomeric Solvent Release-Type Sealants
April 1, 2026 - ASTM International

This test method details the standard procedures for the determination of the bond and cohesion of one-part elastomeric solvent release-type sealants after high- and low-temperature aging. The materials and apparatuses needed for this test procedure are an extension machine, a forced-draft type...

Advertisement