1.1 This test method applies to non-floating biodegradable plastics intended for use in aerobic aquatic environments, specifically in marine, brackish, or fresh water ecosystems. The plastics covered under this test method are designed to not persist in the environment by converting into carbon...
1.1 This test method describes the general requirements for evaluating the long-term, chlorinated water, oxidative resistance of polypropylene (PP) piping produced in accordance with Specification F2389 used in hot-and-cold water distribution systems by exposure to hot, chlorinated water....
1.1 This test method covers the determination of load-deflection characteristics of plastic pipe under parallel-plate loading. 1.2 This test method covers thermoplastic resin pipe, reinforced thermosetting resin pipe (RTRP), and reinforced polymer mortar pipe (RPMP). 1.3 The characteristics...
1.1 These practices describe standard procedures for using electrical methods to locate leaks in geomembranes covered with liquid or earthen materials, or both. 1.2 These practices are intended to ensure that leak location surveys are performed to the highest technical capability of electrical...
1.1 This specification covers requirements, test methods, materials, and marking for polypropylene (PP) buried crate systems used for collection, detention, and retention of stormwater runoff. Applications include commercial, municipal, and residential drainage, including installation under...
4.1 This test method is designed to produce tensile property data for the control and specification of nonreinforced polyethylene and flexible nonreinforced polypropylene geomembranes. These data are also useful for qualitative characterization and for research and development. It may be...
5.1 Like other techniques to measure toughness, this test method provides a means to determine parameters of a material at strain rates closer to some end-use applications than provided by low-speed uniaxial tensile tests. Dynamic tensile behavior of a film is important, particularly when the film...
1.1 This practice covers procedures for testing single joints of thermoplastic pipe for gravity flow (non-pressure) sewer lines, when using either air or water under low pressure to demonstrate the integrity of the joint. This practice is used for testing 27 in. (675 mm) and larger inside diameter...
1.1 This practice is a performance-based standard for an electrical method for locating leaks in exposed conductive-backed geomembranes. For clarity, this practice uses the term "leak" to mean holes, punctures, tears, knife cuts, seam defects, cracks, and similar breaches in an installed...
1.1 This guide covers recommendations for the selection of appropriate test methods for flexible polypropylene sheet used in geomembrane applications to provide consistency in data reporting. 1.2 This guide includes test methods for three types of flexible polypropylene geomembranes,...
1.1 This guide describes standard procedures for using electrical conductance measurement methods to locate leaks in exposed or covered roofing and waterproofing membranes. 1.2 This guide addresses the need for a general technical description of the current methods and procedures that are used to...
This specification covers requirements, test methods, materials, and marking for polypropylene (PP), open bottom, buried chambers of corrugated wall construction used for collection, detention, and retention of stormwater runoff. Applications include commercial, residential, agricultural,...
1.1 This practice standardizes structural design of thermoplastic corrugated wall arch-shaped chambers used for collection, detention, and retention of stormwater runoff. The practice is for chambers installed in a trench or bed and subjected to earth and live loads. Structural design includes the...
1.1 This specification covers requirements, test methods, materials, and marking for closed-cell cellular polypropylene (PP), open bottom, buried chambers of corrugated wall construction used for collection, detention, and retention of stormwater runoff. Applications include commercial,...
1.1 This specification is applicable to the use of plastic lumber materials and of wood-plastic composite materials, and no other plastic composite materials, used as exterior wall coverings, as part of an exterior wall assembly. 1.2 This specification is not applicable to the use of plastic lumber...
4.1 This test method is designed to produce tensile property data for the control and specification of nonreinforced polyethylene and flexible nonreinforced polypropylene geomembranes. These data are also useful for qualitative characterization and for research and development. It may be...
1.1 This practice describes procedures for making joints with pressure-rated polypropylene (PP) pipe and fittings by means of heat fusion joining in, but not limited to, a field environment. This standard does not purport to address all possible heat fusion joining procedures or to preclude...
1.1 This test method describes destructive quality control and quality assurance tests used to determine the integrity of geomembrane seams produced by thermo-fusion methods. This test method presents the procedures used for determining the quality of nonbituminous bonded seams subjected to both...
1.1 This test method describes the general requirements for evaluating the long-term, chlorinated water, oxidative resistance of polyethylene (PE), used in cold water supply or service systems by exposure to chlorinated water. This test method outlines the requirements of a pressurized flow-through...
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, elongation, brittleness, pipe stiffness, and markings for single wall corrugated polypropylene (PP) pipe and fittings. It covers nominal sizes 3 in. through 30 in. (75 mm through 750 mm). 1.2...
Narrow Your Results