loading
ASTM D8646-26 - Standard Test Method for Calculating and Reporting the Estimated Biodegradation Time of Non-Persistent Plastics Designed for Use in Aquatic Environments
May 15, 2026 - ASTM International

1.1 This test method applies to non-floating biodegradable plastics intended for use in aerobic aquatic environments, specifically in marine, brackish, or fresh water ecosystems. The plastics covered under this test method are designed to not persist in the environment by converting into carbon...

ASTM F3497-26 - Standard Test Method for Evaluating the Oxidative Resistance of Polypropylene (PP) Piping Systems to Hot Chlorinated Water
February 1, 2026 - ASTM International

1.1 This test method describes the general requirements for evaluating the long-term, chlorinated water, oxidative resistance of polypropylene (PP) piping produced in accordance with Specification F2389 used in hot-and-cold water distribution systems by exposure to hot, chlorinated water....

ASTM D2412-26 - Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
April 1, 2026 - ASTM International

1.1 This test method covers the determination of load-deflection characteristics of plastic pipe under parallel-plate loading. 1.2 This test method covers thermoplastic resin pipe, reinforced thermosetting resin pipe (RTRP), and reinforced polymer mortar pipe (RPMP). 1.3 The characteristics...

ASTM D8265-26 - Standard Practices for Electrical Methods for Mapping Leaks in Installed Geomembranes
April 1, 2026 - ASTM International

1.1 These practices describe standard procedures for using electrical methods to locate leaks in geomembranes covered with liquid or earthen materials, or both. 1.2 These practices are intended to ensure that leak location surveys are performed to the highest technical capability of electrical...

ASTM F3754-25 - Standard Specification for Polypropylene (PP) Crate Stormwater Storage System
December 1, 2025 - ASTM International

1.1 This specification covers requirements, test methods, materials, and marking for polypropylene (PP) buried crate systems used for collection, detention, and retention of stormwater runoff. Applications include commercial, municipal, and residential drainage, including installation under...

ASTM D6693/D6693M-25 - Standard Test Method for Determining Tensile Properties of Nonreinforced Polyethylene and Nonreinforced Flexible Polypropylene Geomembranes
December 1, 2025 - ASTM International

4.1 This test method is designed to produce tensile property data for the control and specification of nonreinforced polyethylene and flexible nonreinforced polypropylene geomembranes. These data are also useful for qualitative characterization and for research and development. It may be...

ASTM D3420-21(2026) - Standard Test Method for Pendulum Impact Resistance of Plastic Film
February 1, 2026 - ASTM International

5.1 Like other techniques to measure toughness, this test method provides a means to determine parameters of a material at strain rates closer to some end-use applications than provided by low-speed uniaxial tensile tests. Dynamic tensile behavior of a film is important, particularly when the film...

ASTM F3058-16(2026) - Standard Practice for Preliminary Field Testing of Thermoplastic Pipe Joints for Gravity Flow (Non-Pressure) Sewer Lines
February 1, 2026 - ASTM International

1.1 This practice covers procedures for testing single joints of thermoplastic pipe for gravity flow (non-pressure) sewer lines, when using either air or water under low pressure to demonstrate the integrity of the joint. This practice is used for testing 27 in. (675 mm) and larger inside diameter...

ASTM D7240-25 - Standard Practice for Electrical Leak Location Using Geomembranes with an Insulating Layer in Intimate Contact with a Conductive Layer via Electrical Capacitance Technique (Conductive-Backed Geomembrane Spark Test)
December 1, 2025 - ASTM International

1.1 This practice is a performance-based standard for an electrical method for locating leaks in exposed conductive-backed geomembranes. For clarity, this practice uses the term "leak" to mean holes, punctures, tears, knife cuts, seam defects, cracks, and similar breaches in an installed...

ASTM D6434-25 - Standard Guide for the Selection of Test Methods for Flexible Polypropylene Geomembranes
April 1, 2025 - ASTM International

1.1 This guide covers recommendations for the selection of appropriate test methods for flexible polypropylene sheet used in geomembrane applications to provide consistency in data reporting. 1.2 This guide includes test methods for three types of flexible polypropylene geomembranes,...

ASTM D7877-25 - Standard Guide for Electronic Methods for Detecting and Locating Leaks in Roofing and Waterproofing Membranes
August 15, 2025 - ASTM International

1.1 This guide describes standard procedures for using electrical conductance measurement methods to locate leaks in exposed or covered roofing and waterproofing membranes. 1.2 This guide addresses the need for a general technical description of the current methods and procedures that are used to...

ASTM F2418-25 - Standard Specification for Polypropylene (PP) Corrugated Wall Stormwater Collection Chambers
March 1, 2025 - ASTM International

This specification covers requirements, test methods, materials, and marking for polypropylene (PP), open bottom, buried chambers of corrugated wall construction used for collection, detention, and retention of stormwater runoff. Applications include commercial, residential, agricultural,...

ASTM F2787-13(2025) - Standard Practice for Structural Design of Thermoplastic Corrugated Wall Stormwater Collection Chambers
August 1, 2025 - ASTM International

1.1 This practice standardizes structural design of thermoplastic corrugated wall arch-shaped chambers used for collection, detention, and retention of stormwater runoff. The practice is for chambers installed in a trench or bed and subjected to earth and live loads. Structural design includes the...

ASTM F3430-25 - Standard Specification for Closed-Cell Cellular Polypropylene (PP) Corrugated Wall Stormwater Collection Chambers
May 1, 2025 - ASTM International

1.1 This specification covers requirements, test methods, materials, and marking for closed-cell cellular polypropylene (PP), open bottom, buried chambers of corrugated wall construction used for collection, detention, and retention of stormwater runoff. Applications include commercial,...

ASTM D8484-25 - Standard Specification for Plastic Lumber Materials and Wood-Plastic Composite Materials Used as Exterior Wall Coverings
June 1, 2025 - ASTM International

1.1 This specification is applicable to the use of plastic lumber materials and of wood-plastic composite materials, and no other plastic composite materials, used as exterior wall coverings, as part of an exterior wall assembly. 1.2 This specification is not applicable to the use of plastic lumber...

ASTM D6693/D6693M-20(2024) - Standard Test Method for Determining Tensile Properties of Nonreinforced Polyethylene and Nonreinforced Flexible Polypropylene Geomembranes
November 1, 2024 - ASTM International

4.1 This test method is designed to produce tensile property data for the control and specification of nonreinforced polyethylene and flexible nonreinforced polypropylene geomembranes. These data are also useful for qualitative characterization and for research and development. It may be...

ASTM F3722-24 - Standard Practice for Heat Fusion Joining of Polypropylene (PP) Pipe and Fittings
October 1, 2024 - ASTM International

1.1 This practice describes procedures for making joints with pressure-rated polypropylene (PP) pipe and fittings by means of heat fusion joining in, but not limited to, a field environment. This standard does not purport to address all possible heat fusion joining procedures or to preclude...

ASTM D6392-25 - Standard Test Method for Determining the Integrity of Nonreinforced Geomembrane Seams Produced Using Thermo-Fusion Methods
March 1, 2025 - ASTM International

1.1 This test method describes destructive quality control and quality assurance tests used to determine the integrity of geomembrane seams produced by thermo-fusion methods. This test method presents the procedures used for determining the quality of nonbituminous bonded seams subjected to both...

ASTM F2263-25 - Standard Test Method for Evaluating the Oxidative Resistance of Polyethylene (PE) Pipe to Chlorinated Water
March 1, 2025 - ASTM International

1.1 This test method describes the general requirements for evaluating the long-term, chlorinated water, oxidative resistance of polyethylene (PE), used in cold water supply or service systems by exposure to chlorinated water. This test method outlines the requirements of a pressurized flow-through...

ASTM F3219-24 - Standard Specification for 3?in. to 30 in. (75?mm to 750 mm) Polypropylene (PP) Corrugated Single Wall Pipe and Fittings
November 15, 2024 - ASTM International

1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, elongation, brittleness, pipe stiffness, and markings for single wall corrugated polypropylene (PP) pipe and fittings. It covers nominal sizes 3 in. through 30 in. (75 mm through 750 mm). 1.2...

Advertisement