loading
AS90708C - RING, RETAINING, EXTERNAL, INTERLOCKING
March 20, 2023 - SAE International
A description is not available for this item.
ISUZU ISD-F01-500 - Retaining rings
July 1, 2018 - ISUZU

This standard covers the retaining rings (hereinafter referred to as "rings"), mainly for automotive uses.

NAS1930 - RING, RETAINING
September 19, 2014 - AIA/NAS
A description is not available for this item.
MIL-DTL-21248 - RING, RETAINING (TAPERED AND REDUCED SECTION TYPE)
June 20, 2019 - NPFC

Scope. This specification covers the procurement requirements for tapered and reduced section type retaining rings of rectangular and beveled cross - section.

MS 25086 - RING, RETAINING
NPFC
A description is not available for this item.
MIL-R-48006 - RING, RETAINING
NPFC
A description is not available for this item.
ASME B107.19 - Pliers, Retaining Ring
January 1, 2004 - ASME

This Standard provides performance and safety requirements for pliers suitable for inserting and removing internal and external retaining rings including those covered by ASME B18.27. Inclusion of dimensional data in this Standard does not mean that all pliers described herein are...

AS90708B - RING, RETAINING, EXTERNAL, INTERLOCKING
June 29, 2017 - SAE International
A description is not available for this item.
AS90708A - RING, RETAINING, EXTERNAL, INTERLOCKING
August 19, 2016 - SAE International
A description is not available for this item.
MS 9014 - RING-RETAINING, INTERNAL, STEEL
June 13, 1960 - NPFC

THIS STANDARD WAS DEVELOPED COOPERATIVELY WITH THE ENGINE AND PROPELLER UTILITY PARTS COMMITTEE OF THE SAE NOTICE: When Government drawings, specifications, or other data are used for any purpose other than in connection with a definitely related Government procurements operation, the United States...

ASTM C1372-24 - Standard Specification for Dry-Cast Segmental Retaining Wall Units
December 1, 2024 - ASTM International

1.1 This specification covers dry-cast segmental retaining wall units of concrete, machine-made from hydraulic cement, water, and suitable mineral aggregates with or without the inclusion of other materials. The units are intended for use in the construction of mortarless segmental...

GMW17568 - Procedure for Qualifying Liquid Fuel Quick Connect Fittings for Nylon Fuel Line, PTFE Hose, and Elastomeric Hose Usage
April 1, 2018 - GMW

Purpose. This specification covers quick connector fittings intended to be used with nylon fuel lines. The fuel system quick connector consists of a case, two O-rings, spacers, and a retaining clip. Applicability. Add content.

ASTM C1262/C1262M-26 - Standard Test Method for Evaluating the Freeze-Thaw Durability of Dry-Cast Segmental Retaining Wall Units and Related Concrete Units
June 1, 2026 - ASTM International

1.1 This test method covers the resistance to freezing and thawing of dry-cast segmental retaining wall (SRW) units (see Specification C1372) and related concrete units. Units are tested in a test solution that is either potable tap water or 3 % saline solution depending on the intended use...

ASTM D7132-19(2026) - Standard Test Method for Determination of Retained Blowing Agent in Extruded Polystyrene Foam
July 1, 2026 - ASTM International

This test method covers the determination of retained blowing agent in extruded polystyrene foam. The internal standard preparation procedures of the material are presented in details. The procedures for determination of retained blowing agent in extruded polyester foam are presented...

GMKOREA EDS-G-2107 - E Ring-Retaining
November 1, 2012 - GMKOREA
A description is not available for this item.
GMKOREA EDS-G-2105 - C Ring-Retaining
November 1, 2012 - GMKOREA
A description is not available for this item.
ASTM A788/A788M-26a - Standard Specification for Steel Forgings, General Requirements
August 1, 2026 - ASTM International

1.1 This specification covers a group of common requirements that, unless otherwise specified in the individual product specification, shall apply to steel forgings under any of the following specifications issued by ASTM: ASTM Designation Title A266/A266M Carbon Steel Forgings for Pressure Vessel...

A-A-55488 - PIN, RETAINING, SAFETY
August 19, 2019 - NPFC

This commercial item description (CID) depicts the requirements for a safety retaining pin.

ASTM F1807-26 - Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring, or Alternate Stainless Steel Clamps, for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
February 1, 2026 - ASTM International

This specification covers metal insert fittings and copper crimp rings for use with SDR9 cross-linked polyethylene (PEX) tubing. All performance tests shall be performed on assemblies of fittings, crimp rings, and PEX tubing. Fittings and crimp rings shall meet the material and...

ASTM A788/A788M-26 - Standard Specification for Steel Forgings, General Requirements
July 1, 2026 - ASTM International

1.1 This specification covers a group of common requirements that, unless otherwise specified in the individual product specification, shall apply to steel forgings under any of the following specifications issued by ASTM: ASTM Designation Title A266/A266M Carbon Steel Forgings for Pressure Vessel...

Advertisement